ignition Seat Ibiza 2020 Directive 2014/53/EU Bluetooth

Page 22 of 90 Report No. : 60404487 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
5.7.5 Earthed accessible conductive parts ..................... : N/A
5.7.6 Requirements when touch current exceeds ES2
limits N/A
Protective c onductor current (mA) ......................... : N/A
Instructional Safeguard ................................ .......... : N/A
5.7.7 Prospective touch voltage and touch current
associated with external circuits N/A
5.7.7.1 Touch current from coaxial cables N/A
5.7.7.2 Prospective touch voltage and touch current
ass ociated with paired conductor cables N/A
5.7.8 Summation of touch currents from external circuits N/A
a) Equipment connected to earthed external
circuits, current (mA) ................................ ............. : N/A
b) Equipment connected to unearthed external
circuits, current (mA) ................................ ............. : N/A
5.8 Backfeed safeguard in battery backed up supplies
N/ A
Mains terminal ES ................................ ..................... : No battery backed up supplies N/ A
Air gap (mm) ................................ .............................. : N/ A

6 ELECTRICALLY - CAUSED FIRE
P
6.2 Classification of PS and PIS
P
6.2.2 Power source circuit classifications .......................... : (See appended table 6.2.2) P
6.2.3 Classification of potential ignition sources P
6.2.3.1 Arcing PIS ................................ ................................ : Open circuit voltage does not
exceed 50 V N/A
6.2.3.2 Resistive PIS ................................ ............................ : (See appended table 6.2.3.2) P
6.3 Safeguards against fire under normal operatin g and abnormal operating
conditions P
6.3.1 No ignition and attainable temperature value less
than 90 % defined by ISO 871 or less than 300  C
for unknown materials ................................ ........... : No ignition and no such
temperature attained within
the equipment P
Combustible materi als outside fire enclosure .......... : Min. HB P
6.4 Safeguards against fire under single fault conditions
P
6.4.1 Safeguard method Control fire spread P
6.4.2 Reduction of the likelihood of ignition under single
fault conditions in PS1 circuits N/A

Page 23 of 90 Report No. : 60404487 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
6.4.3 Redu ction of the likelihood of ignition under single
fault conditions in PS2 and PS3 circuits N/A
6.4.3.1 Supplementary safeguards N/A
6.4.3.2 Single Fault Conditions ................................ .......... : N/A
Special conditions for temperature limited by fuse N/A
6.4.4 Control of fire spread in PS1 circuits P
6.4.5 Control of fire spread in PS2 circuits P
6.4.5.2 Supplementary safeguards For conductor and devices are
mounted on printed board
made of Min. V - 1.
Other components in PS2 are
mounted on printed board
made of Min. V - 1 and PVC
wire used .
Not ignite during single fault
condition . P
6.4.6 Control of fire spread in PS3 circuits Provided Metallic enclosure P
6.4.7 Separation of combustible materials from a PIS P
6.4.7.2 Separation by distance N/A
6.4.7.3 Separation by a f ire barrier P
6.4.8 Fire enclosures and fire barriers P
6.4.8.2 Fire enclosure and fire barrier material properties P
6.4.8.2.1 Requirements for a fire barrier V - 0 class material or metal,
Printed board made of V - 0 P
6.4.8.2.2 Requirem ents for a fire enclosure Metallic enclosure provided P
6.4.8.3 Constructional requirements for a fire enclosure
and a fire barrier P
6.4.8.3.1 Fire enclosure and fire barrier openings P
6.4.8.3.2 Fire barrier dimensions P
6.4.8.3.3 Top openings and properties E quipment for building - in ,
e valuation shall be considered
in the end product N/A
Openings dimensions (mm) ................................ ... : N/A
6.4.8.3.4 Bottom openings and properties E quipment for building - in ,
e valuation shall be considered
in the end product N/A
Open ings dimensions (mm) ................................ ... : N/A
Flammability tests for the bottom of a fire enclosure N/A

Page 41 of 90 Report No. : 60404487 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
M.6.1 External and internal faults N/A
M.6.2 Compliance N/A
M.7 Risk of explosion from lead acid and NiCd batteries
N/A
M.7.1 Ventilation preventing explosive gas concentration N/A
Calculated hydrogen generation rate .................... : N/A
M.7.2 Test method and compliance N/A
Minimum air flow rate, Q (m 3
/h) ............................. :
N/A
M.7.3 Ventilation tests N/A
M.7.3.1 General N/A
M.7.3.2 Ventilation test – alternative 1 N/A
Hydrogen gas concentration (%) ........................... : N/A
M.7.3.3 Ventilation test – a lternative 2 N/A
Obtained hydrogen generation rate ....................... : N/A
M.7.3.4 Ventilation test – alternative 3 N/A
Hydrogen gas concentration (%) ........................... : N/A
M.7.4 Marking ................................ ................................ .. : N/A
M.8 Protection against internal ignition from external spark sources of batteries
wit h aqueous electrolyte N/A
M.8.1 General N/A
M.8.2 Test method N/A
M.8.2.1 General N/A
M.8.2.2 Estimation of hypothetical volume V
Z (m 3
/s) ......... :


M.8.2.3 Correction factors ................................ .................. :

M.8.2.4 Calculation of distance d (mm) ............................. :


M.9 Preventing electrolyte spillage
N/A
M.9.1 Protection from electrolyte spillage N/A
M.9.2 Tray for preventing electrolyte spillage N/A
M.10
Instructions to prevent reasonably foreseeable
misuse N/A
Instructional safeguard ................................ .......... : N/A
N ELECTROCHEMICAL POTENTIALS
N/A
Mater ial (s) used ................................ ..................... :


Page 21 of 89 Report No. : 60404488 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
5.7.5 Earthed accessible conductive parts ..................... : N/A
5.7.6 Requirements when touch current exceeds ES2
limits N/A
Protective conductor current (mA) ......................... : N/A
Instructional Safeg uard ................................ .......... : N/A
5.7.7 Prospective touch voltage and touch current
associated with external circuits N/A
5.7.7.1 Touch current from coaxial cables N/A
5.7.7.2 Prospective touch voltage and touch current
associated with paired conductor cables N/A
5.7.8 S ummation of touch currents from external circuits N/A
a) Equipment connected to earthed external
circuits, current (mA) ................................ ............. : N/A
b) Equipment connected to unearthed external
circuits, current (mA) ................................ ............. : N/A
5.8 Backfeed safeguard in battery backed up supp lies
N/ A
Mains terminal ES ................................ ..................... : No battery backed up supplies N/ A
Air gap (mm) ................................ .............................. : N/ A

6 ELECTRICALLY - CAUSED FIRE
P
6.2 Classification of PS and PIS
P
6.2.2 Power source circuit classifications .......................... : (See appended table 6.2.2) P
6.2.3 Classification of potential ignition sources P
6.2.3.1 Arcing PIS ................................ ................................ : Open circuit voltage does not
exceed 50 V N/A
6.2.3.2 Resistive PIS ................................ ............................ : (See appended table 6.2.3.2) P
6.3 Safeguards against fire under normal operating and abnormal operating
conditions P
6.3.1 No ig nition and attainable temperature value less
than 90 % defined by ISO 871 or less than 300  C
for unknown materials ................................ ........... : No ignition and no such
temperature attained within
the equipment P
Combustible materials outside fire enclosure .......... : Min. HB P
6.4 Safeg uards against fire under single fault conditions
P
6.4.1 Safeguard method Control fire spread P
6.4.2 Reduction of the likelihood of ignition under single
fault conditions in PS1 circuits N/A

Page 22 of 89 Report No. : 60404488 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
6.4.3 Reduction of the likelihood of ignition under single
f ault conditions in PS2 and PS3 circuits N/A
6.4.3.1 Supplementary safeguards N/A
6.4.3.2 Single Fault Conditions ................................ .......... : N/A
Special conditions for temperature limited by fuse N/A
6.4.4 Control of fire spread in PS1 circuits P
6.4.5 Control of fire s pread in PS2 circuits P
6.4.5.2 Supplementary safeguards For conductor and devices are
mounted on printed board
made of Min. V - 1.
Other components in PS2 are
mounted on printed board
made of Min. V - 1 and PVC
wire used .
Not ignite during single fault
cond ition . P
6.4.6 Control of fire spread in PS3 circuits Provided Metallic enclosure P
6.4.7 Separation of combustible materials from a PIS P
6.4.7.2 Separation by distance N/A
6.4.7.3 Separation by a fire barrier P
6.4.8 Fire enclosures and fire bar riers P
6.4.8.2 Fire enclosure and fire barrier material properties P
6.4.8.2.1 Requirements for a fire barrier V - 0 class material or metal,
Printed board made of V - 0 P
6.4.8.2.2 Requirements for a fire enclosure Metallic enclosure provi ded P
6.4.8.3 Constructional requirements for a fire enclosure
and a fire barrier P
6.4.8.3.1 Fire enclosure and fire barrier openings P
6.4.8.3.2 Fire barrier dimensions P
6.4.8.3.3 Top openings and properties E quipment for building - in ,
e valuation shall be considered
in the end product N/A
Openings dimensions (mm) ................................ ... : N/A
6.4.8.3.4 Bottom openings and properties E quipment for building - in ,
e valuation shall be considered
in the end product N/A
Openings dimensions (mm) ................................ ... : N/A
Flammability tests f or the bottom of a fire enclosure N/A

Page 40 of 89 Report No. : 60404488 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
M.6.1 External a nd internal faults N/A
M.6.2 Compliance N/A
M.7 Risk of explosion from lead acid and NiCd batteries
N/A
M.7.1 Ventilation preventing explosive gas concentration N/A
Calculated hydrogen generation rate .................... : N/A
M.7.2 Test method and compliance N/A
Minimum air flow rate, Q (m 3
/h) ............................. :
N/A
M.7.3 Ventilation tests N/A
M.7.3.1 General N/A
M.7.3.2 Ventilation test – alternative 1 N/A
Hydrogen gas concentration (%) ........................... : N/A
M.7.3.3 Ventilation test – alternative 2 N/A
Obtained hydrogen generation rate ....................... : N/A
M.7.3.4 Ventilation test – alternative 3 N/A
Hydrogen gas concentration (%) ........................... : N/A
M.7.4 Marking ................................ ................................ .. : N/A
M.8 Protection against internal ignition from external spark sources of batteries
with aqueous electrolyte N/A
M.8.1 General N/A
M .8.2 Test method N/A
M.8.2.1 General N/A
M.8.2.2 Estimation of hypothetical volume V
Z (m 3
/s) ......... :


M.8.2.3 Correction factors ................................ .................. :

M.8.2.4 Calculation of distance d (mm) ............................. :


M.9 Preventing electrolyte spillage
N/A
M.9.1 Protection from electrolyte spillage N/A
M.9.2 Tray for preventing electrolyte spillage N/A
M.10
Instructions to prevent reasonably foreseeable
misuse N/A
Instructional safeguard ................................ .......... : N/A
N ELECTROCHEMICAL POTENTIALS
N/A
Material (s) used ................................ ..................... :


Page 20 of 88 Report No. : 60404489 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
5.7.5 Earthed accessible conductive parts ..................... : N/A
5.7.6 Requirements when touch current exceeds ES2
limits N/A
Protective conductor current (mA) ......................... : N/A
Instructional Safeguard ................................ .......... : N/A
5.7.7 Prospective touch voltage and touch current
associated with external circuits N/A
5.7.7.1 Touch current from coaxial cables N/A
5.7.7.2 Prospective touch voltage and touch current
associated with paired conductor cables N/A
5.7.8 Summation of touch currents from external circ uits N/A
a) Equipment connected to earthed external
circuits, current (mA) ................................ ............. : N/A
b) Equipment connected to unearthed external
circuits, current (mA) ................................ ............. : N/A
5.8 Backfeed safeguard in battery backed up supplies
N/ A
Mains terminal ES ................................ ..................... : No battery bac ked up supplies N/ A
Air gap (mm) ................................ .............................. : N/ A

6 ELECTRICALLY - CAUSED FIRE
P
6.2 Classification of PS and PIS
P
6.2.2 Power source circuit classifications .......................... : (See appended table 6.2.2) P
6.2.3 Classification of potential ignition sources P
6.2.3.1 Arcing PIS ................................ ................................ : Open circuit voltage does not
exceed 50 V N/A
6.2.3.2 Resistive PIS ................................ ............................ : (See appended table 6.2.3.2) P
6.3 Safeguards against fire under normal operating and abnormal operating
conditions P
6.3.1 No ignition and attainable temperature value less
than 90 % defined by ISO 871 or less than 300  C
for unknown materials ................................ ........... : No ignition and no such
temperature attained within
the equipment P
Combustible materials outside fire enclosure .......... : Min. HB P
6.4 Safeguards against fire under single fault conditi ons
P
6.4.1 Safeguard method Control fire spread P
6.4.2 Reduction of the likelihood of ignition under single
fault conditions in PS1 circuits N/A

Page 21 of 88 Report No. : 60404489 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
6.4.3 Reduction of the likelihood of ignition under single
fault conditions in PS2 and PS3 circuits N/A
6.4.3.1 Supplementary safeguards N/A
6.4.3.2 Single Fault Conditions ................................ .......... : N/A
Special conditions for temperature limited by fuse N/A
6.4.4 Control of fire spread in PS1 circuits P
6.4.5 Control of fire spread in PS2 circuits P
6.4.5.2 Supplementa ry safeguards For conductor and devices are
mounted on printed board
made of Min. V - 1.
Other components in PS2 are
mounted on printed board
made of Min. V - 1 and PVC
wire used .
Not ignite during single fault
condition . P
6.4.6 Control of fire spread in PS3 circuits Provided Metallic enclosure P
6.4.7 Separation of combustible materials from a PIS P
6.4.7.2 Separation by distance N/A
6.4.7.3 Separation by a fire barrier P
6.4.8 Fire enclosures and fire barriers P
6.4.8.2 Fire enclosure and fire bar rier material properties P
6.4.8.2.1 Requirements for a fire barrier V - 0 class material or metal,
Printed board made of V - 0 P
6.4.8.2.2 Requirements for a fire enclosure Metallic enclosure provided P
6.4.8.3 Constructional requirements fo r a fire enclosure
and a fire barrier P
6.4.8.3.1 Fire enclosure and fire barrier openings P
6.4.8.3.2 Fire barrier dimensions P
6.4.8.3.3 Top openings and properties E quipment for building - in ,
e valuation shall be considered
in the end product N/A
Openings dimensions (mm) ................................ ... : N/A
6.4.8.3.4 Bottom openings and properties E quipment for building - in ,
e valuation shall be considered
in the end product N/A
Openings dimensions (mm) ................................ ... : N/A
Flammability tests for the bottom of a fire enclosure N/A

Page 39 of 88 Report No. : 60404489 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
M.6.1 External and interna l faults N/A
M.6.2 Compliance N/A
M.7 Risk of explosion from lead acid and NiCd batteries
N/A
M.7.1 Ventilation preventing explosive gas concentration N/A
Calculated hydrogen generation rate .................... : N/A
M.7.2 Test method and compliance N/A
Minimum a ir flow rate, Q (m 3
/h) ............................. :
N/A
M.7.3 Ventilation tests N/A
M.7.3.1 General N/A
M.7.3.2 Ventilation test – alternative 1 N/A
Hydrogen gas concentration (%) ........................... : N/A
M.7.3.3 Ventilation test – alternative 2 N/A
Obtained hydrogen generation rate ....................... : N /A
M.7.3.4 Ventilation test – alternative 3 N/A
Hydrogen gas concentration (%) ........................... : N/A
M.7.4 Marking ................................ ................................ .. : N/A
M.8 Protection against internal ignition from external spark sources of batteries
with aqueous electrolyte N/A
M.8.1 General N/A
M.8.2 Test method N/A
M.8.2.1 General N/A
M.8.2.2 Estimation of hypothetical volume V
Z (m 3
/s) ......... :


M.8.2.3 Correction factors ................................ .................. :

M.8.2.4 Calculation of distance d (mm) ............................. :


M.9 Preventing electrolyte spillage
N/A
M.9.1 Protection from electrolyte spillage N/A
M.9.2 Tray for preventing electrolyte spillage N/A
M.10
Instructions to prevent reasonably foreseeable
misuse N/A
Instructional safeguard ................................ .......... : N/A
N ELECTROCHEMICAL POTENTIALS
N/A
Material (s) used ................................ ..................... :


Page 20 of 88 Report No. : 60404490 001

IEC 62368 - 1
Clause Requirement + Test Result - Remark Verdict


TR F No. IEC62368_1 C
5.7.5 Earthed accessible conductive parts ..................... : N/A
5.7.6 Requirements when touch current exceeds ES2
limits N/A
Protective conductor current (mA) ......................... : N/A
Instructional Safeguard ................................ .......... : N/A
5.7.7 Prospective touch voltage and touch current
associated with external circuits N/A
5.7.7.1 Touch current from coaxial cables N/A
5.7.7.2 Prospective touch voltage and touch current
associated with paired conductor cables N/A
5.7.8 Summation of touch currents from external circ uits N/A
a) Equipment connected to earthed external
circuits, current (mA) ................................ ............. : N/A
b) Equipment connected to unearthed external
circuits, current (mA) ................................ ............. : N/A
5.8 Backfeed safeguard in battery backed up supplies
N/ A
Mains terminal ES ................................ ..................... : No battery bac ked up supplies N/ A
Air gap (mm) ................................ .............................. : N/ A

6 ELECTRICALLY - CAUSED FIRE
P
6.2 Classification of PS and PIS
P
6.2.2 Power source circuit classifications .......................... : (See appended table 6.2.2) P
6.2.3 Classification of potential ignition sources P
6.2.3.1 Arcing PIS ................................ ................................ : Open circuit voltage does not
exceed 50 V N/A
6.2.3.2 Resistive PIS ................................ ............................ : (See appended table 6.2.3.2) P
6.3 Safeguards against fire under normal operating and abnormal operating
conditions P
6.3.1 No ignition and attainable temperature value less
than 90 % defined by ISO 871 or less than 300  C
for unknown materials ................................ ........... : No ignition and no such
temperature attained within
the equipment P
Combustible materials outside fire enclosure .......... : Min. HB P
6.4 Safeguards against fire under single fault conditi ons
P
6.4.1 Safeguard method Control fire spread P
6.4.2 Reduction of the likelihood of ignition under single
fault conditions in PS1 circuits N/A