key Seat Ibiza SC 2013 BLUETOOTH SYSTEM

4Introduction to the Bluetooth systemIntroduction to the Bluetooth systemGeneral information
This system allows you to connect your mobile phone via
Bluetooth connection and to use the hands-free mode.
The hands-free device means that the telephone can be used inside the ve-hicle; the driver will not have to remove their hands from the steering wheelnor will be distracted from traffic.
Available functions include making calls in hands-free mode, access to themobile phone address book, access to the call list and control of the voicerecognition system.
Before using the Bluetooth system, the mobile phone should be connectedto the vehicle installation via Bluetooth ⇒ page 7.
Switching on/off
The Bluetooth system is activated when the ignition is turned on and it isdeactivated when the key is removed from the ignition.
With the system activated, if the “PTT” ( - Push to talk) button is pressedon the multifunction control, the voice control activates and if there is notelephone connected, Bluetooth visible is turned on and a search for a tele-phone is begun.
If there is a call in process when the system is deactivated, the active call isnot cancelled, but transferred to the mobile phone.
Bluetooth
Bluetooth technology permits the connection of a mobile phone to the vehi-cle hands free system. In order to use the system with a mobile phone withBluetooth technology, the process of pairing them must be performed in ad-vance.
Use compatible Bluetooth devices only. For more information about compat-ible Bluetooth products, consult your dealership or the SEAT website.
Some Bluetooth mobile phones are detected and connected automaticallywhen the ignition is switched on. For this to take place the telephone mustbe switched on and its Bluetooth function activated, and there must be noactive Bluetooth connection from other devices.
Bluetooth connections are free.
Bluetooth® is a registered trademark of Bluetooth® SIG, Inc.
Declaration of conformity
S1nn GmbH & Co. KG certifies that the UHV High unit complies with the ba-sic requirements and the rest of the relevant provisions of the Directive1999/5/CE. A copy of the declaration of conformity can be found at http://www.s1nn.de/certifications/uhv-high-manual .
Exchange of information between the mobile phone and the Bluetoothsystem
The mobile phone system sends the data and the requests via Bluetooth tothe mobile phone that is connected. If the connected mobile phone is tem-porarily “overloaded”, it may not respond to the requests from the Blue-tooth system.
In this case, wait for the mobile phone to react or make a new call.

7Getting started: LinkingGetting started: LinkingCreation of user profile
Each telephone must be paired to the Bluetooth system be-
fore using it for the first time.
When pairing a mobile phone for the first time, you will be asked to create auser profile. A user profile is necessary for you to connect the mobile phoneto the SEAT system. Once the user profile has been created, your telephonecan be connected automatically or manually. It is not necessary to repeatthe initial connection process each time.
A maximum of four user profiles can be created. If you try to create a fifthprofile, the profile which has been inactive for the most time will automati-cally be deleted.
The pairing process can take several minutes depending on the size of thephone book.
The procedure for pairing your mobile phone to the SEAT system for the firsttime is described below.

Pairing with the mobile phone
Follow the steps below to connect the mobile phone to the vehi-
cle's Bluetooth by searching for devices from the mobile phone:
–
Activate the Bluetooth in the mobile phone.
–Turn on the ignition with the key. The vehicle system will be visi-
ble to the mobile phone via Bluetooth for 3 minutes. If the 3 mi-
nutes have passed you can also switch on Bluetooth visible
again for 3 minutes by pressing the button “PTT” (Push To Talk
⇒ Fig. 2).
–
Search for Bluetooth devices using the mobile phone. Refer to
the mobile phone manual for instructions.
–
A list of devices found is displayed on the mobile phone. From
this list, select the device SEAT_BT.
–
Next, accept the connection instructions on the mobile phone.
–
When requested, follow the steps to confirm/enter the PIN. If
the mobile requests a PIN to be entered this is 1234, which is
the factory setting and can only be changed at the workshop.
Depending on the technology supported by your mobile the
process can vary given that some mobiles only request confir-
mation of a request to link to SEAT_BT, while others require the
PIN 1234 to be entered.
–
The contacts from the mobile phone's memory and/or SIM
card1) are transferred to the vehicle system. Some mobile
phones may display a message asking for confirmation of ac-
cess to the phone book or other options, these messages
should be accepted in order for the hands free system to access
the information contained on the mobile and in order to carry
out the complete functions of the system.
1)
Depending on the phone model and configuration.

8Getting started: Linking–The pairing is complete.
Note
The visibility of the Bluetooth system in the vehicle is activated for 3 mi-nutes when the ignition is turned on with the key. After 3 minutes, if youneed to activate the visibility again, you can do so with the voice control⇒ page 9 or turning the ignition off and on again.
Note
If for any reason you take more than 3 minutes to perform these steps ormore than 30 seconds to enter the PIN, you will have to start the processover again.

Automatic pairing
When the telephone has been connected and the corresponding user pro-file created, your telephone will automatically link up with the SEAT tele-phone system under the following conditions:
●
The mobile phone is switched on with the Bluetooth function activatedand the visibility activated. The mobile phone must be close to the vehicle.
●
The vehicle system has switched on Bluetooth visible (during the 3 mi-nutes following activation of the contact or after pressing the button “PTT”).
●
The automatic connection was accepted during the questions of the firstconnection.
●
The connection to the system has not been deleted in the mobile.
With the ignition switched on, the system searches in the memorised Blue-tooth devices (user profiles), and if one of these devices is found a connec-tion attempt is made to connect to the last linked profile that meets the pre-viously mentioned requirements. The system will continue connection at-tempts while there is no connected device.
When a Bluetooth device is connected or when the automatic connectionconditions are met, in order to connect another Bluetooth device, an exist-ing connection or one that is in the process being connected must be deac-tivated in advance. In order to do this, deactivate the Bluetooth on the un-wanted device.
