ESP Seat Leon 5D 2008 COMMUNICATION SYSTEM

Communication25
Controls and equipment
Dialogue
The voice command system can be activated with the “press
to talk” button, located on the multi-function control.
In this manual, Dialogue is defined as the time in which the voice command
system may receive vocal commands and provide assistance for the comple-
tion of different functions where the user is hesitant and unsure how to
proceed. The system also responds with vocal messages. The dialogue starts
and is stopped by pressing the “press to talk” button Ÿpage 23, fig. 11
or on the radio display.
If a call is received, then the dialogue is immediately interrupted. The call may
be accepted by pressing the key “answer” on the multi-function control.
Assistance from voice control system when commands are not recognised.
If a command is not recognised by the system, it will answer with the cue
and the command can then be given once again clearly.
After a third failure the system will answer with and the dialogue will
be ended. Please note the following to ensure that you are properly understood:
•Speak in a normal tone and without pauses or exaggerated pronuncia-
tion.
•Avoid poor articulation of words.
•Keep the doors, windows and sun roof closed if possible to avoid back-
ground noises that might affect the system.
•Keep the air vents directed away from the microphone (located on the
interior light).
•At high speeds, you might need to speak louder to drown out background
noises.
•Avoid other noises in the vehicle during a dialogue (e.g. other passengers
speaking in the vehicle).
•Avoid speaking when the system is saying a cue.
•The hands-free microphone is directed towards the driver, therefore, only
the driver should try to operate the system.
•To make a call when there is heavy background noise we recommend
using the speech controlled telephone book instead of saying individual
digits. This will help avoid mistakes when specifying telephone numbers.
Micro off
If, at any time, we do not wish to be heard by the person on the other end of
the line during a call, the vehicle microphone can be temporarily discon-
nected. To do so, press the multi-function button on the radio (see Radio
manual) during the call.
To reactivate the micro, press the multi-function button on the radio again
(see Radio manual).Fig. 15 Current phone
call
ACok

AA
AA

Communication
28
system will repeat the digits. The system can only recognise single digits
(one, zero, two, five, etc.), and not combinations of digits (e.g. ten, twenty-
five). Notes on specifying telephone numbers:
•If the telephone number has more than 20 digits, the system will decline
and give the cue .
•A Plus (+) can also be placed ahead of the 20 digits.
Example of how to enter a telephone number:
A running dialogue can be cancelled at any time by pressing the talk button Ÿ page 22, fig. 9 .
CommandConditionMessageEffect
DIAL NUMBERPhone switched onDialogue
for example, ZERO, SEVEN, THREE,
ONEDialogue
If no command is specified, the system responds after about 5 seconds with the next cue.
No command back, or specify additional digits>Dialogue
THREE, NINE, TWODialogue
DIALDialogue -The telephone number
0731492 will be dialled
End of dialogue
AC

Communication
30
A running dialogue can be cancelled at any time by pressing the talk button
Ÿ page 23, fig. 10 .
Note
•If the telephone number has more than 20 digits, the system will decline
and give the cue .
•A Plus (+) can also be placed ahead of the 20 digits.
•Say the command delete or back to delete or correct the corresponding
block of digits.
•Say repeat to have all the digits that have been recognised up to that
point repeated.
•If two or more names sound alike, it is better to save the names including
the first name or some other distinguishing entry.
•A running dialogue can be cancelled at any time by pressing the talk
button .
•The phone book works only in conjunction with the hands-free voice
command system; the entries are not stored on the phone SIM card.
COMPANY XYZDialogue
ZERO, ONE, TWO, THREEDialogue
FOUR, FIVE, SIXDialogue
If no command is specified, the system responds after about 5 seconds with the next cue.
No command repeat, back, delete, or specify addi-
tional digits>Dialogue
STOREDialogue - The name COMPANY XYZ
with the telephone number 0123456
has been stored
End of dialogue
AC
AC

Communication31
Controls and equipment
Calling a name in the phone book
– Press the talk button .
– After the tone, say the command SELECT NAMEAfter the system has recognised this command, you may select a stored entry
from the telephone book to call the required number. The system best recog-
nises names spoken by the person who stored the name.
Example of how to select an entry from the phone book
A running dialogue can be cancelled at any time by pressing the talk button Ÿ page 23, fig. 10 .AC
CommandConditionMessageEffect
SELECT NAMEPhone is switched on, telephone book
contains entries.Dialogue
COMPANY XYZDialogue
If no command is specified, the system responds after about 5 seconds with the next cue.
No command repeat, back>Dialogue
DIALDialogue - The telephone number for
Company XYZ is being dialled
End of dialogue
AC

Communication33
Controls and equipmentExample of how to delete one entry from the phone book:
A running dialogue can be cancelled at any time by pressing the talk button
Ÿ page 22, fig. 9.
Note
•Say the command Repeat, if you would like to have the specified name
repeated by the system.
•If you then say No, the system will answer with and the dialogue
will be ended.
To delete the phone book
You can delete the entire phone book or single entries.
– Press the talk button Ÿpage 22, fig. 9 .
– After the tone, say the command DELETE PHONE BOOK.
After giving this command you can delete the entire internal phone book or
single entries as desired.
CommandConditionMessageEffect
DELETE NAMEThe telephone book contains entries.Dialogue
COMPANY XYZ pany XYZ?>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue
No command repeat, back>Dialogue
Ye sDialogue
End of dialogue
AC
AC

Communication
34
Example of how to delete the entire phone book:
Example of how to delete one entry from the phone book:
CommandConditionMessageEffect
DELETE PHONE BOOKThe telephone book contains entries. phone book?>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue
No commandDialogue
Ye sDialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue
No commandDialogue
Ye sDialogue - All entries in the phone
book will be deleted.
End of dialogue
CommandConditionMessageEffect
DELETE PHONE BOOKThe telephone book contains entries. phone book?>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue
No command repeat>Dialogue
NODialogue - The telephone book will
then be read out.
No commandTalk button pressed as the entry to
be deleted is read out. (name)?>Dialogue
If no command is specified, the system responds after about 5 seconds with the next cue.Dialogue
AC