light Seat Tarraco 2018 Owner's Guide

Driver assistance systems
When the driver touches the accelerator
pedal or accel er
at
es slightly to continue driv-
ing, the Auto Hold function releases the brake.
The vehicle moves according to the slope of
the road.
If the vehicle is stationary and one of the con-
ditions required by the Auto Hold function is
impaired, it disconnects itself and the button

Driving
Note
Before entering a car wash, always switch
off the Auto Hol d function, because if the
el
ectronic parking brake is automatically
connected, it may cause damage. Cruise control system
(CCS)*
Control l amp %
It lights up green
The Cruise Control System (GRA) is switched on and
active .
OR:

The Adaptive Cruise Contr ol syst
em (CCS) is
switched on and active.
OR: the speed limiter is s wit
ched on and active.Several warning and control lamps light up
f
or a f
e

w seconds when the ignition is switch-
ed on, signalling that the function is being
verified. They will switch off after a few sec-
onds. WARNING
Observe the safety warnings

Driver assistance systems
After overtaking, the speed limiter can be
s wit
ched on with the pr
eviously set speed by
pressing button 3 on the turn signal lever in
the ar ea


 or by moving the third lever into
pressure point .
Switch the speed limiter off temporarily by
pressing down the accelerator (kick-
down)
If the accelerator is pressed right down (kick-
down) and the set speed is exceeded be-
cause driver wishes to do so, the limiter is
temporarily disabled.
To confirm it being switched off an acoustic
signal sound once. While the limiter is off, the
warning and control lamp  flashes. When the accelerator is no longer pressed
down and the speed is reduced below the set
value, the limiter switches on again. The con-
trol lamp  will light up and remain lit.
Automatic off
The speed limiter is automatically switched
off:

Driver assistance systems
light up on the instrument panel, and the pro-
gr ammed speed and ACC st
at
us will be dis-
played

Driver assistance systems
Overtaking
When the t urn signal lights up bef
or
e the ve-
hicle begins an overtaking manoeuvre, the
ACC accelerates the vehicle automatically
and thus reduces the distance from the vehi-
cle in front.
When the vehicle enters the overtaking lane,
if the ACC does not detect another vehicle in
front, it accelerates until it reaches the pro-
grammed speed and maintains it.
System acceleration can be interrupted at
any time by pressing the brake or moving the
third lever backwards

Driving
Trailer mode
When driving with tr ail
er the ACC contr
ols
less dynamically.
Overheated brakes
If the brakes overheat, for example after
abrupt braking or in long and steep slopes,
the ACC may be deactivated temporarily.
The relevant text message will appear in the
dash panel display. In this case, adaptive
cruise control cannot be activated.
Adaptive Cruise Control can be reactivated
once brake temperature has cooled suffi-
ciently. The message will disappear from the
instrument panel display. If the message ACC
not available remains on for quite a long
time it means that there is a fault. Contact a
specialised workshop. SEAT recommends vis-
iting a SEAT dealership. WARNING
If you do not heed the Press the brake
message, the v ehicl

e may initiate an invol-
untary movement and could crash into the
vehicle ahead. In any event, before driving
off, check that the road is clear. The radar
sensor may not detect obstacles on the
road. This could cause an accident and se-
rious injuries. If necessary, apply the brake. Lane Assist system*
Intr oduction Fig. 270
On the windscreen: field of vision of
the L ane Assist syst
em camer

a. Using the camera located in the windscreen,
the L
ane Assist syst
em det

ects the possible
lines dividing the lanes. When the vehicle in-
voluntarily approaches a dividing line it has
detected, the system notifies the driver with a
corrective steering movement. The purpose is
not only to warn the driver, but also to keep
the vehicle inside the lane. This movement
can be over-regulated at any time.
No warning is produced with the turn signals
activated, given that the Lane Assist system
understands that a lane change is required.
As soon as the ignition is switched on, the
lane departure function is automatically acti-
vated. Control lamp "
It lights up yellow
Lane Assist active but not available.
The system cannot accurat
ely recognise the lane.
Please see page 294, Lane Assist system is not avail-
able (the control lamp is lit up yellow). "
It lights up green
Lane Assist system active and available. Some control and warning lamps will light up
briefly when the ignition is s
wit
ched on t

o
check certain functions. They will switch off
after a few seconds. WARNING
Observe the safety warnings

Driving
Lane Assist with lane centring guide
The Lane Centring Guide function is inten-
ded t o k
eep the vehicle in the centre of the
lane.
If the driver has a tendency to veer slightly off
centre in the lane, the system adapts to driver
preferences.

Driver assistance systems
chapter, do not use it and contact a speci-
alised workshop
.Control lamps
Control lamp in external rear view mirrors:

It lights up
It lights up once briefly: the blind spot detector is ac-
tivat ed and r
eady to operate.
It lights up: blind spot detector has detected a vehi-
cle in the blind spot. 
Flashes
The blind spot detector has detected a vehicle in the
blind spot and the turn signal has been t urned on in
the dir

ection of the detected vehicle

Driver assistance systems
Using the blind spot detector (BSD)
with parking assist ant (RC
T
A)Activating and deactivating the blind spot
detect
or (BSD) with parking assist

ant
(RCTA)
The blind spot detector with parking assistant
can be switched on and off by accessing the
Assistance systems menu on the dash
panel display using the steering wheel con-
trols. If the vehicle is equipped with a multi-
function camera, it can also be accessed by
means of the driver assistance systems key
located on the main beam headlight lever.
Open the Assistants menu.

Driving
Key to the Fig. 298:
Pin Meaning
4 Right turn signal5 Rear light, right
6 Brake lights 7 Rear light, left
8 Reverse lights
9 Permanent live
10 Live charge cable 11 Earth for pin 10
12 Unassigned
13 Earth for pin 9 Trailer power socket
The v
ehicl
e is fitt
ed with a 13-pole power
socket for the electrical connection between
the trailer and the vehicle. With the engine
running, electrical devices on the trailer re-
ceive power from the electrical connection
(pin 9 and pin 10 of the trailer power socket).
If the system detects that a trailer has been
connected electrically, the electrical equip-
ment on the trailer will receive voltage
through this connection (pins 9 and 10). Pin 9
has a permanent live. This powers, for exam-
ple, the trailer