run flat Seat Tarraco 2020 Owner's manual

Self-help
Jump start: description Fig. 43
Diagram of connections for vehicles
without St art
-Stop system. Fig. 44
Diagram of connections for vehicles
with St art

-Stop system. Jump lead terminal connections
Swit

ch off the ignition of both vehicles
››› .
1. Connect one end of the r
ed

jump lead to
the positive + terminal of the vehicle
with the fl at batt
ery A
› ›
› Fig. 43
.
Connect the other end of the red jump
lead to the positive terminal + in the ve-
hicl e pr

oviding assistance B .
In v ehicl
es without a Start-Stop system:
connect one end of the black jump lead
to the negative terminal – of the vehicle
pr o

viding the current B
› ›
› Fig. 43
.
In vehicles with a Start-stop system:
connect one end of the black jump lead X to a suitable ground terminal, to a sol-
id piece of met al in the engine bl

ock, or
to the engine block itself ››› Fig. 44
.
Connect the other end of the black jump
lead X to a solid metal component bol-
t ed t

o the engine block or to the engine
block itself of the vehicle with the flat
battery. Do not connect it to a point near
the battery A .
P osition the l

eads in such a way that
they cannot come into contact with any
moving parts in the engine compart-
ment.
Starting Start the engine of the vehicle with the
boosting battery and let it run at idling
speed.
2.
3.
4a.
4b.
5.
6.
7.
Start the engine of the vehicle with the
flat batt

ery and wait for 2 or 3 minutes
until the engine is running.
Removing the jump leads Before you remove the jump leads,
switch off the dipped beam headlights if
they are switched on.
Turn on the heater blower and heated
rear window in the vehicle with the flat
battery. This helps minimise voltage
peaks which are generated when the
leads are disconnected.
When the engine is running, disconnect
the leads in reverse order to the details
given above.
Make sure the battery clamps have sufficient
metal-to-metal contact with the battery ter-
minals.
If the engine fails to start after about 10 sec-
onds, switch off the starter and try again after
about 1 minute. WARNING

Driving
for a minimum of about 5 seconds already
sav es mor
e than the amount of fuel necessa-
ry for restarting.
The engine takes a long time to warm up
when it is idling. Mechanical wear and pollu-
tant emissions are also especially high during
this initial warm-up phase. It is therefore best
to drive off immediately after starting the en-
gine. Avoid running the engine at high speed.
Regular maintenance
Regular servicing helps in saving fuel even
before the engine is started. A well-serviced
engine gives you the benefit of improved fuel
efficiency as well as maximum reliability and
an enhanced resale value. A badly serviced
engine can consume up to 10% more fuel
than necessary.
Avoid short journeys
The engine and catalytic converter need to
reach their optimal operating temperature
in order to minimise fuel consumption and
emissions.
A cold engine consumes a disproportionate
amount of fuel. The engine reaches its work-
ing temperature after about four kilometres
(2.5 miles), when fuel consumption will return
to a normal level. Check tyre pressure
Alw
ays make sure the tyres are inflated to the
correct pressures ››› page 356
to save fuel. If
the pressure is below half bar, fuel consump-
tion may increase by 5%. Due to the greater
rolling resistance, under-inflation also increa-
ses tyre wear and impairs handling.
Do not use winter tyres all year round as
they increase fuel consumption by up to 10%.
Avoid carrying unnecessary loads
Given that every kilo of extra weight will in-
crease the fuel consumption, it is advisable
make sure that no unnecessary loads are be-
ing transported.
Since the luggage rack increases the aero-
dynamic drag of the vehicle, you should re-
move it when not needed. At speeds of
100-120 km/h (62-75 mph), this will save 12%
of fuel.
Save electrical energy
The engine drives the alternator, thereby
generating electricity. This implies that any
increase in power consumption also increa-
ses fuel consumption! For this reason, switch
off any unneeded electrical devices. Devices
that use a lot of electricity includes the blow-
er at a high setting, the rear window heating
or the seat heating*. Plug-in hybrid drive: brak
e early and evenly
to take advantage of energy recovery. Note