wheel bolts SKODA 120 LSE 1980 Workshop Manual

il
tli
GEARBOX. FINAL
DRIVE
Connection DimensionsTightening
torque Nmt)
Nuts of cosing clomping bolts .
Nut of primory shoft
Plnlon nut .
Nut of pinion
beoring coP
Nut of releose sleeve
bol
Nut of front cover bolt
Nut of speedometer shoft clip bolt
Nut of speedometer drive beoring
bolt
Nut of reverse-geor pin
bolt
Bolt of reverse-geor pin
Bolt of shifter forks
Bolt of cop of lock-boll springs
Silentblock bolt
Bolt of differentiol cose
Bolt of crown geor
Droin ond inspection hole plugs
Switch or bolt of reversing lomps .
REAR AXLE
Connection M8
M 22x1.5
M 24x1.5
M8
M6 M8
M 22x1.5
M 14x1
Dimensions 40-50
14-17
6-8 19-25
7-9
7-9 17 -20
7 -9
14-17
7 -9
30-40 22-25
35-45
20-30
70-80
M6
M6
M8
M8
M6
M6
M10
M8
M 10x1 30-35
7 -9
Tightening torque Nmr)
Rood wheels nuts .
Nut of oxle-shoft boll
Nut of oxle shoft
.ioin;
boit M 12x1.5
M8 M 18x1.5
M8
M10
Dimension 60-70
20-25
17O *)
a
40-50
Bolt of broke
bocking plote
Bolt of wheel cylinder
FRONT AXIE
Connection Tightening
torque Nml)
Nut fostening lower wishbone fulcrum
brocket to bodywork
Nut of lower wishbone fulcrum
brocket
(next to rubber bush -
inner)
Ditto -
outer lock nut .
Nut of upper wishbone fulcrum
brocket
(next to rubber bush -
inner)
Ditto -
outer lock nut .
Nut of upper wishbone pin (connection
with steering
knuckle pivot)
Nut of lower wishbone pin (connection
with steering
knuckle socket)
Nut of wheel
hub beoring .
Nut of steering knuckle pivot
.
Nut of lower
wishbone brocket bolt .
Nut of bolt fostening shock obsorber to its onchor brocket
Nut fostening shock
obsorber to
bodywork
Wheel nuts
Bolt fostening
front oxle to bodywork .
Bolt of
onti-roll bor brocket see
Chopter 6.5, points
24 ond 25
see Chopter 6.5, point
21
M
,M M
M
M
M 12x1.5
12x1.5
12x1.5
12x1.5
12x1.5
12x1.5 6s-70
45-60
70-90
45-60
70-90
70*)
70 *l
40-50 50-55 12-14
60-70
40-45
12-16
M
12x1.5
M10
M 12x1.5
M10
M 12x1.5
M10
M7
*) Further tightening os
required for olignlng holes
for the cotter pin.
22

primory
feed to the distributor coincides with
the connecting line of the
distributor centre
line ond the first cylinder
heod
bolt os
per
Fig.2.3l10. Secure the distributor in this pos-
ition by lightly tightenning the tie-bolt ond
remove the timing geor
cover from the cylinder
block. The used type of distributor is described
in Chopter 13.5.
Fig.2.3l10 -
Position of Distributor on Engine
-l - screw of primory power
feed
2 -
cylinder heod bolt
3 -
index line rnorking the position
of the
distributor ornr when cvlinder No. 1 f ires
24. Coot with oil the moting
surfoces of the
timing geor cover ond the cylinder
block, locote
the cover gosket
on the block,
oil the timing
choin ond the comshott worm geor.
Remove the
f lywheel powl
ond rotote the
cronkshoft through
360o so
os to bring tlre pistons
of the cylinders
No. 1 ond 4 to their TDC position
ogoin. This
position corresponds opproximotely
to the volve
geor position
when the cylinder No. 1 f ires (the
tips of the coms of
cylinder No. 1 ore turned
downword, owoy from
the engine). Lock the
cronkshoft in position by refitting ond tight-
ening the flywheel powl.
25. Turn
the distributor orm in the direction
of the
screw (1) in occordonce with Fig. 2.3110,
hold it down with the
finger in this position,
ond ref it the timing geor
cover on the cylinder
block. By sliding the worm geor
of the distribu-
tor drive into the comshoft worm geor,
the orm
is turned to coincide with the timing
mork for
cylinder No. 1
on the distributor housing. lf
there is no coincidence of the orm ond timing
mork, od just
the position
of the orm by
slightly
rototing the distributor.
lf the
misolignment of the distributor
ornr
ond the timinq
mork of the
cvlinder
No'1 is so greot
thot it connot be corrected
by rototing
the distributor, remove
the timing geor
cover,
rotote the distributor slightly ond repeot
the
entire procedure
of refitting the timing geor
cover. 26. Smeor the protruding
end of the cronk-
shoft ond the outer shoft end (stem)
of the
belt
pulley with oil, f
it the belt pulley,
the nespective
wosher, ond tighten the bolt. Bolt the
PumP
suction stroiner tothe cronkshoft centre beoring
ond use o spring
wosher under the bolt heod.
27. Bolt down the timing geor
cover using
spring woshers ond
cheese-heod bolts
(exclus-
ively) cnd f inolly fosten the timing geor
cover
in such o position
thot the contoct breoker
points open before the crronkshoft with
the con-
necting rod ond piston
hos ottoined the top
deod centre (TDC)
position (see
the lgnition
Timing Toble in Chopter 15.3).
For checking the ignition odvonce, on electric
power supply is required with o bulb connected
in o circuit with the distributor. this
circuit
being interrupted by the oction of the contoct
breoker. An odopted conventionol torch with o
metol
iocket con be
used with odvontoge for this
purpose. Remove the flywheel powl ond
set the re-
quired ignition odvonce by turning the cronk-
shoft with o screw'driver inserted into
the geor
ring ond propped ogoinst the cylinder block
f longe. Rotote the shof t onticlockwise o bit
more thon necessory ond
bock it off so os to
odiust the bocklosh of the timing geors
ond the
distributor drive geors.
oK 6ls
Fi9.2.3111- Lomp for Checking the Opening
of Contoct Breoker Points
-1 - torch complete with dry cell ond bulb
2 -
leod with olligotor clomp
3 -
botterv cell
4 -
torch coo
5 -
contoct spring
6 -
insuloting plote
7 -
electricol-contoct connection of the leod
with the
drv cell Con
using
torch.
the br
slowly
indico
A corr
is not
timing 28.L
beorin
Then f
while
oil sun
the thr
the tyl
see Cl.
shri n ks
of the
woter
move i
ively.
To Fit
Toppetr
25. r
remove
positior
sure thr
cylinder
cylinder nuts. F<
first bo
woteir p
oir clec
finol ti1
2.16.
Ploin
heod bo
which t
woshers
no wosl
heod bo
cy I i nder
the outs
hove to
of the rc
Tighte
broce or,
30. Sc
thermom
into the
cosing o
ofter ho
Use spri
thermost
cooted g
with the
with the
The th
should br
34

ilil
ll
I
Z,l
spring woshers under the pump
fostening nuts.
36. lnstoll the oil filter -
see Oil Filter in
Chopter 15.3.
37. Bolt the brocket ond the reloy lever
of the
occelerotor linkoge to the intoke monifold, Use
spring woshers to lock the bolts in position.
38. Locote the corburettor gosket, sheet
guord, onother gosket,
the insuloting wosher,
ond o third gosket (oltogether
three goskets
of
the some type) on the intoke monifold inlet
socket, instoll the corburettor,
ond tighten
it
down with nuts.
On 105 ond 120 l- engines, the sheet guord
must be fitted to the intoke monifold inlet
socket with o throttling spider, while 120 LS
engines must hove the possoge
unobstructed.
39. Smeor the boll pins
of the linkoge
ond
corburettor lever with greose
contoining molyb-
denum disulphide
ond mount on them the oc-
celerotor link (tie-rod).
Hold the link in pliers
ond slip securing clips over the heods.
Hook o spring on the shonk of the reloy
link-
oge boll pin
ond on the rib of the forehousing
on the corburettor.
40. Screw down the vocuum
control pipe
on
the corburettor (using
double-sided seoling
rings) ond slip on the rubber
hose connecting
the pipe
with the distributor vocuum control
unit. Secure the pipe
by bending the clip under
the nut of the intoke ond exhoust monifold.
To Refit Alternotor
41. Attoch the olternotor
brocket to the side
of the cylinder block while putting
ploin
woshers under
the nuts. Mount the olternotor
holder together with the engine mounting lug
on the bolt of the timing geor
cover ond the
front lug of the cylinder block.
Use self-locking
nuts for the bolts f ostening the olternotor
holder. Lock
the lower bolt of the lug by meons
of o spring wosher
ond nut. Using onother bolt,
bolt together the lug ond the brocket. lnsert
the tie-bolt from
the side
of the lug, slip on
o ploin
wosher ond tighten the nut. Fit the
short-circuit strip on the bolt ond lock it in
o position
porollel
with the olternotor brocket
by screwing
down the respective nut with
o ploin
wosher.
42. Put the olternotor into the holder,
ttrreod
in the bolt, ond screw down the nut with o ploin
wosher without tightening. Without tightening
the self-locking
nut, bolt the strut into the
brocket on the cylinder heod. Swing the olter-
notor toword the engine, fit
the V-belt ond,
while tensioning it, connect the olternotor with
the strut using o bolt, spring wosher ond nut.
At the some time, tighten the nut of the bolt
holding down the olternotor
in the
holder ond
the nut of the bolt connecting the strut with
the holder. For the belt slock odiustment see
Chopter 15.3. 43.
Fosten the second
engine mounting lug
using nuts with spring woshers.
To Fit Cylinder Heod, Air
Cleoner,
ond Sporking Plugs
44. Fit the cylinder heod
with cemented.on
gosket on the cylinder block ofter hoving slip-
ped o seoling ring ond o wosher on eoch bolt,
the some os in the cose of the push-rod
cover.
In oddition, fit the fuel pipe
holder on the reor
bolt ond hold it down by slightly tightening the
nut.
45. Fit the oir cleoner in position
ond fosten
it to the corburettor with o bolt using o seoling
ring ond wosher. Put o spring wosher
under the
nut on the brocket
ond screw down the nut on
the bolt of the cover without ony wosher.
46. Threod the fuel hose through its holder
on the cylinder heod ond use clips to fosten it
to the corburettor ond pump.
Adiust the most
suitoble position of the hose by rototing
the
holder ond then tighten the nut.
47. Attoch hoses connecting the oir cleoner
with the corburettor ond the oil filler neck.
When preporing
the cc for driving in winter,
instoll the winter
oir-intoke tube (hose) -
for
detoiled instructions see Chopter 15.3 "Air
Cleoner -
Winter Operotion".
48. Screw in the sporking plugs
with seoling
iings ond fit the ignition cobles. For the re-
commended types of sporking plugs
see Chopter
13.7.
The outlet on the distributor cop morked with
o notch is intended for
the coble
to cylinder
No. 1. The
remoining outlets ore.to be counted
clockwise ond in direct
order from 1
to 4 ond
the cobles will be connected to sporking plugs
in the order of numbers cost on the cylinder
heod beside the recesses for sporking plugs.
Plug Screws ond Lubricotion
System
Accessories
49. Plug the oil sump with the conicol screw
plug with its
seoling ring. In the cose of on
engine without the oil cooler, plug
the oilwoy
on the timing geor
cover with o screw plug
with o seoling
ring, ond the oilwoy ot the reor
end of the cylinder block with o pressure
switch. lf the socket for screwing down the
pressure switch is missing, instoll o new socket
together with its respective seoling ring.
lf on oil cooler is provided,
hoses ond o press-
ure switch should be
connected to the oilwoys
occording to Chopter 11.9.
Put the oil dipstick
with the f itted rubber ring
in its ploce.
For the type of the dipstick see
Chopter 2.17.
50. Using spring
woshers with the bolts,
screw down the flywheel
guorcl
ofter removing
36

Turn
the flonge
on the centering
orbor so thot
the longer, cylindricol port
foces the clutch,
push it ogoinst the friction plote
hub, ond olign
the ends of the levers to touch the flonge.
A deviotion from the ploneness
of 0.1 mm
is
permissible. Use feeler gouges for checking
this deviotion.
lf it is not possible
to odiust the out-trovel of
the clutch releose levers to o volue given
by the
length of the flonge cylindricol port
due to
excessive weor
of the friction plote, odiust to
the next higher volue.
Clinch nuts on the
odiusting nuts bocked off up to the end of the
threod ore o worning of o weor limit which pre-
cludes ony further odiustment
of the clutch.
4. After hoving reossembled
the engine with
o new or odiusted clutch,
check ond, if necess-
ory, odiust the cleoronce between the releose
levers ond the throw-out beoring -
see Chop-
ter 15.4.
3.3 CLUTCH DISMANTLING
Owing to its simplicity,
it is not necessory
to
describe in detoil the dismontling
of the clutch,
but some speciol feotures
deserve ottention.
1. lf the friction plote
ond clutch cover ore
intended to be re-used, mork their relotive
positions using centre punch
morks to preserve
the originol bolonce of the ossembly.
2. To dismontle
the clutch, it is
necessory to
compress the clutch cover to relieve the stress
of the releose lever bolts. For this purpose
use
the MP 2-101
ossembly plote
shown in Fig.3.4/1.
After screwing off the releose lever nuts ond
compressing the clutch cover,
the clutch is
reody for dismontling.
3.4 CLUTCH REASSEMBLY
1. Locote
the clutch pressure
plote
on the
MP 2-101
ossembly plote
ond fit springs
on the
cylindricol bosses. Before fitting
the springs, it
is odvisoble to check them for
complionce with
the volues specified
in the following Toble.
Toble of Clutch Springs
Lood
Length of spring in mm
lin -rrr"ltp1
Mounted length
31.55'10+36
(s2t3.6)
Length of compressed spring 29.5
I 580 (59) 2.
Instoll retoining plotes
on the clutch
springs ond fit the clutch cover with releose
lever springs in position.
Assemble the clutch
cover with the pressure plote,
observing the
morks indicoting their relotive positions.
When
ossembling new pot'ts,
their positions
ore of no
consequence.
3. Slip o 4.5 mm high pod
over the ossembly
plote bolts (the
plote
con be used
for Skodo
1000 MB ond Skodo 100 cors os well,
ond by
using pods
of different heights, the plote
con be
odopted for different
types of clutches), fit the
yoke of the
iig on
the plote
bolt ond compress
it by screwing down the nut till the bottom port
rests on the pod.
When compressing the clutch
cover toke core thot the projections
of the
pressure plote
ore correctly centered in
the
cover slots to prevent
o distortion of the clutch
cover.
4. Slip the bottom ends of the releose levers
under the springs instolled in the cover ond fit
them with their longitudinol
slots on the sup-
ports. Slip odiusting woshers on the bolts of the
pressure plote ond screw down the nuts with
their cylindricol port
focing the woshers. Then
odjust the height of the releose levers with
these nuts so thot their ends touch the shoulder
of the yoke
bottom port.
The difference of the
lever height should not exceed 0.'l mm. This
odiustment olso sets the recommended
distonce
of the levers from the pressure
plote
beoring
surfoce.
Use clinch nuts for locking the odiusting nuts
in position,
put
supporting clips under the re-
leose f ever ends os shown in Fig.3.111 ond3.212,
ond slocken the nuts of the ossembly plote.
The
clips ore useful when fitting the clutch to the
f lywheel since it is not necessory to overcome
the tension of the clutch springs.
To Check Adiustment ond Bolance
The described od justment
of the releose levers
in the
iig is
the most occurote, the ossembly Fig.3
Dim
plote be
simulotin
For on<
porogropl
The cl
with the
friction ;
ports of '
clutch on
To bol
centering
pressure
the chips
lf thesr
boloncing ing holes
in o circk
4mmofr
between
fostening
3.5 FR|C
lf the f
it is odvi
8.5 mm th
When r
the frictio
ond only r
complicot
After hr
the plote
if necessc
recheckinl
quired.
70 Fig.3.4l1
-
IAP 2lol
Assembly Plote with Clutch

Proceed
in the some woy with the
3rd- ond
4th-speed geors.
lf the morked position
of the neutrol is not
midwoy between the side morks (check
visu-
olly), remove the pinion,
mork the positions
of
the striking forks on
their rods (preferobly
on
either side), slocken the forks ond 'rnove
them
toword the required centre by
the distonce of
the deviotion of the neutrol morking. Then lock
the striking forks in position
with screws.
For the striking fork tightening torgue see
Chopter 1.8. 13. Adiust the reverse geor position
so thot
there is o gop
of obout 2
mm between its teeth
ond the odioining teeth, ond swing the striking
fork of the first ond second speed
to moke sure
thot it connot foul
the teeth.
14. Reinstoll the pinion
with its respective
woshers ond lock it in position.
Shift the strik-
ing fork rods to moke sure thot, for exomple,
o movement opposite to the required one of the
striking forks did not toke ploce,
i. e. thot the
neutrol is midwoy betvr'een the engogement
positions of the synchronizing clutches. Correct
ony error ond remove
ogoin the pinion.
Fitting Drive Geors ond Clutch Shqft
15. lnstoll the ossembled drive shoft into the
housing ond slip the splined bush on it.
Top home the seol ring with its seoling lip
pointing outwords into the guide
of the clutch
thrrowout sleeve, ond smeor it with oil. Then
threod the clutch shoft through the ring to
instoll it into the splined bush ond put
it into
the housing together with the guide provided
with o cooting of seoling compound on its cyl-
indricol bedding surfoce. Secure both the shoft
ond the sleeve with circlips.
lnstoll the sleeve guide
with its droin hole
level with the porting plone
of the housing ond
focing the pinion.
For the speciol seoling compound see the
note in Chopter 10.1.
16. Put the pinion
with geors
into the housing
ond oil oll synchronizing rings. Fit the MP 5-104
iig for
setting the crown wheel bocklosh into
the bore of the differentiol beoning ond the
fitted cover, fit the ossembled differentiol in it,
ond close the housing with the other housing
holf ofter hoving cooted the seoling surfoces
with o seoling compound.
Fit o rubber ring in the recess of the boss
beside the stud
bolt ond put
o spring wosher
under the nut. Tighten the remoining nuts
without ony woshers (the
stress of the bolts
ofter the tightening of the nuts provides
for'
their suff icient securing). Tighten the nuts
moderotely for the time being.
For the speciol seoling
compound refer to the
note in Chooter 10.'1. 17.
Proceeding through
the bore of the differ-
entiol beoring in the upper holf of the housing,
fit another
iig, the MP
5-104,
on to the differen-
tiol with flonges clomped so os to fit
into the
topered roller beoring cover, locote the cover
pocking, ond fosten
the cover by meons
of three
nuts. lf the clomping or drowing close of the
flonges of this jig
proves inodequote, it is
necessory to drow close the flonges olso of
the
first, previously
inserted
iig.
18. Drive the guide
of the clutch throwout
sleeve into the housing using the MP 3-103 drift,
top home the drive shoft, ond insert
two od-
iusting woshers under the collor of the
pinion
shoft boll beoring on both holves of the housing
ofter hoving determined their thickness by
meosuring. Using o wire needle
inserted into
the holes of
the tobs of the woshers orronge the woshers so
thot they do not overlop the porting plone
of
the housing,
then instoll the cover ond spring
woshers, ond tighten the nuts (seeChopter
1.8).
19. Fosten the housing by tightening the nuts
(see Chopter 1.8) ond lock in position
the guide
of the clutch throwout sleeve with the respect-
ive clip using the spring wosher under the
clip
nuts.
4.3 ASSEMBLING
FINAL DRIVE
Ref itting Differentiol 20. Turn the housing into the horizontol pos-
ition. Rotote the ends of the knurled hondles
of the inserted iigs MP 5-104
to move the re-
instolled differentiol (see previous porogrophs
16 ond 17) until the crown wheel withdrows
Fig. 4.311- Adiusting
1 -
MP 5-104 iig,
3 -
MP 5-106
iig,Bevel
Geor Bocklosh
2 -
MP 5-101
iig,
4 -
Screwdriver from
the
Determir
swivellin
To rotr
iig with
tiol stor
21. Ins
on the b,
rotote th
the diol
ible to th
Retoin
ogoinst 1
cover. Tl'
teeth chc
losh on t
of the ho
wheel sic
fied volut
the hond
fully its c
( preferob
wheel). I
opened f1
respectivr
of the
iigr
Now tl"
iusted on
flonges o'
topered r
This situc
trot i o n.
Fig. a3fi
for tc
1
22. Rem
side (turn
withdrow
dimension hos to be
roller beori
Measuring 23. Unscr
the toperer
locote it o
q,
ry
80

Remove the clip of
the
clutch throwout beor-
ing guide,
insert the MP 3-102
iig into
the guide,
open its iows, ond withdrow the
guide.
After
hcving renewed the seol ring, drive home the
guide using the MP 3-103 drift. The droin hole
in the guide
must foce
downword.
The lotest desing of the extrocting
iig hos
the type dcsiqnotion MP 3-112. Screw the
iig
bolt into
the
iig nut
inserted into the mech-
onism through the hole cleored by the removol
of the clutch releose cylinder. Jerk the
iig to
drive the guide
out of the housing.
Dismontling the Power Pock
For complete dismontling of the power pock,
remove it from the cor -
see Chopter 4.-1,
"Rernovol of Power Pock from the Cor". Then
proceed os follows:
1. Remove the front cover ond the cover of
the pinion boll beoring, the clutch releose
mechonism, ond the clip of the guide
of the
clutch throwout sleeve, i. e., oll component
ports ottoched
to both holves of the housing.
2. Remove the connecting bolts of the flon-
ges. Force oport the f longes using o screwdriverr
inserted into the chombers of the flonge feet
(lugs). Lifting owoy oll component ports
one
by one is the usuol procedure
of dismontling.
Toking oport of lorger units (pinion,
etc.) is
described individuolly
in the following
chopters.
3. Press out the beoring cups which hove
remoined in the housing ofter its holves hove
been seporoted.
Use the MP 5-107
iig supported
by the MP 5-108
iig.
Fig.4.al2 -
Pressing Out the Cup of the Topered
Roller Beoring
Using MP 5-107 ond MP 5-108
Jigs
4.5 FRONT COVER
The front cover ossembly forms
o self-con-
toined unit fitted to the georbox.
For both the
reossembly ond dismontling ploce
it on o work
bench. Assembling
Front Cover
1. Slip the rubber seol ring on the speedo-
meter beoring ossembly (beoring
with geors)
ond push
corefully the beoring, preferobly
by
o steody rotory motion, into the cover
iust for
enough to be oble to instoll the key
without
domoging the seol ring by the shorp edge of
the keywoy. For the some reoson, chomfer the edge of the
beoring bore before
instolling the beoring in
o new cover.
2. Lock the beoring in the oxiol direction by
instolling the key
ond spring woshers, ond by
screwing down the nut.
Slip the clip on
the
protruding pcrt of the beoring ond lock it olso
in the oxiol direction with o bolt, spring
wosher,
ond nut. Do not
tighten the nuts fully.
3. Instoll the oiled geor
chonge lever in the
cover while pushing
it only os for os the groove
for the seol
ring.With the lever in this position,
insent the seol ring
in its groove
ond push
forther the lever through the ring. Slip the
dust
boot on the lever ond ottoch it to the cover
with o length
of locking wire.
4. Attoch the fostening (mounting)
lugs using
copscrews ond spring woshers. There
is o right-
-hond ond o left-hond lug, ond their slots must
be turned owov from the cover.
FK 1t't4
Fig.4.5l1- Front
Cove'r Assembly
Dismontling Front Cover
Lift owoy the speedometer
beoring ofter
hoving removed the sleeve
clomping bolt ond
the key (held
down by the nut). Then
withdrow
the geor
chonge lever by simply pulling
it out.
4.6 PINION WITH GEARS The pinion
with geors
forms o self-contoined
unit to be instolled in the georbox.
Use o work
bench ond o press
fon both its ossembly onddismor
wheel sure t
Only c
wheel
m itted
drive.
4.8.
Whe
olso tl
o new
one is
Assem 1.P
the pi
the or" thrust
toworc
3-104 p
ground
the be, must t
meosul
2.S
collor I
ring ir
the grr
The rir
3.5 to I
th ickes
ond pu
speed
3.H
it the '
selecte
toword
dismor (by tol
itinp
free to
Clon
MP 3.1
Note
inner b
toining
either r
-speed
ports.
4. Tr
groovir
pinion.
friction
groover
groove!
5. On
ond fit
the nex sizes 3
84

5.:
pr
stl
bc
5-t
bo
thr
u*,
on
dit
on arI
ioi
sPl
SW
I
gor
:
wo
bol
cyl
del
\
mo
th€ hot
WO
F
clo
POS +:
nec
wol
reo
toe
wit
T
o)
b)
Alil 1.
con
sloc
seo'
int
Fig.5.2l5
-
Pressing Boll Beoring
on Shoft
Using MP 5-112 Jig ond
lts Liner (smoller)
Fig.5.216 -
Connection of
Holf-oxles
with Rodius Arms
lorger ond one smoller, ond the forked plote),
screw down the
iig on the threod
of the shoft,
ond use
nuts to ottoch it
to the holf-oxle socketf
longe. The
iig of
the lotest design permits
its
simple fostening by engogement with
the holf-
oxle flonge (fit
the
iig ond
rotote
it to lock it
in position).
Instoll the lorger liner between the boll
beor-
irrg ond the
iig heod, ond
press
the boll
beorirrg
on the shoft by turning the iig wrench.
3. Reploce the lorger liner with the smoller
one (rest it ogoinst the
iig bolt heod), ond turn
the wrench in the opposite direction to press
the beoring into the holf-oxle socket.
Fitting Broke Mechonism ond Wheel Hub
4. Instoll the broke bocking plote
complete
with the broke
mechonism on the holf-oxle
socket, slip on the "O"
seoling ring ond the
cop with the seoling ring (with
the tightening
f in focing toword the holf-oxle), ond fosten
oll
the porrts
with bolts, spring woshers, ond
nuts.
The seoling ring should be driven or pressed
into the cop so thot the tightening lip foces the
beoring ond
iust so thot there
remoins
o gop
of
1 to 2 mm between the pocking
ond the cop
f longe.
5. lnsert the key in
the shoftwith its bevelled
end into the runout of the keywoy, smeor
the
hub neck with oil so
thot it does not
drog in
the seoling ring, ond fit the hub with the broke
drum in position.
Moke sure thot the key did
not move further olong the shoft (its
lifted end
in the keywoy would couse the hub to burst)
ond tighten
lightly the nut. Since o high
torque
is required
for finol tightening of the nut, put
off the tightening ond locking of the nut till
ofter instollotion in the cor. Then
tighten the
nut with full torque (see
Chopter 1.8),
top on
the hub to relieve
the possive
stress of the
toper, retighten to the specified torque, ond
lock the nut with o cotter pin.
Fitting Rodius Arms
6. Instoll
the spocer into the rodius
orm, fit
the knurled
woshers (with
the knurling toword
the orm)
to either side of the ellipticol holes of
the rodius
orm, ond fosten them with bolts ond
nuts not
forgetting the spring woshers. Do not
tighten the connection fully. Threod
the bolts
through the bolt holes so thot their nuts foce
into the cor ofter fitting the rodius orm to the
holf-oxle.
Fit the rodius
arm on the protruding
holf-oxle
pin ond threod
the bolt through the hole
of the
secrt. Slip
spocing tubes on the bolt ond pin
together with sheet shims with rubber liners
ond fosten
lightly (without tightening)
the
rodius orm to the holf-oxle using nuts
ond lock
woshers. Tighten
fully the connection
ofter fit-
ting the ossembly
in the cor when odiusting
the
reor wheel
olignment (geometry).
il
i
ii
I
I
I
I
lr
il
H, DK
?EI
98

5.5-5.7
the toe-in of the reor
wheels using olso the
MP 8-152 gouge or onother speciol gouge
ovoil-
oble in your
workshop. To
obtoin the required
shift of the holf-oxles (symmetricol
so os not
to
disturb the oxle olignment), strike ogoin the
holf-oxles with o rubber mollet
os per poro-
groph 2.
4" Retighten the slockened connections
(rodius orm bolts) ond, occording to the pro-
gress of the reossembly, olso the nuts of the
holf-oxle shoft (see
Chopter 5.2, porogroph
5).
Complete the operotion by locking the nuts.
Fig. 5.5/3 -
Checking Alignment of Reor Axle
with Cor Centre Line Using MP 8-158
Gouge 5.6 HALF.AXLE DUST BOOTS
To prevent
oil from leoking through the
ioint
gop between the dust boot ond the joint
guord
os well os ony twisting of the boot during
the oction of the rood spring, or its domoge by
contoct with other cor ports,
it is importont to
observe its correct position
on the holf-oxle. lt
should be locoted
with its
flonges focing
reor-
wqrd ond tilted upword ot on ongle of obout
45o. For better occess, ploce
the clips fostening
the dust boot to the holf-oxle ond cover with
their screws on top. With the right-hond
boot,
screw in the clip screws from the front,
with
the left-hond boot the screw on the holf-oxle
from the reor ond on the cover from the front.
Connect the dust boot flonges with hollow
rivets using suitoble pliers.
lf riveting pliers
ore
not ovoiloble, bolt the flonges togethen instol-
ling odequotely dimensioned ploin
woshers
under the bolt heods ond nuts.
5.7 HALF.AXLE SHAFT
The thrust ring of the beoring (behind
the
shoft toper) is pressed
on the shoft. lf it is ne-
cessory to renew this ring, for exomple ofter
repeoted replocements
of the beoring (see
Chopter 5.1, porogrroph
4), press
it on so
thot
it is removed 76 to 78 mm from the edge
of the
toper behind the shoft
threod.
100

wi
prl
tht
rer
oul MT
ott
rec
.a
Fig
Dis S
boll
6-1C
rubl
ovo
exomple
50,000 km ond
more, check the wheel
comber ond prepore
suitoble woshers for its
correction. 2. Jock up the cor ond support the body on
both sides to relieve the front wheels, ond
remove the wheels. 3. Proceeding from
inside the luggoge boot,
remove covers protecting
the threods of the
shock-obsorber piston
rods ond screw off the
nuts. Retoin the piston
rod by holding its flot-
tened end.
b) Operotions inside the cor
4. Remove the steering wheel, the steering
column cowling, ond detoch the steering
shoft
from the body -
see Chopter 7.8.
c) Operotions from under the cor
5. Remove the bolt of the connection of the
steering shoftwith the steering box ond releose
the shoft sleeve from the connection by pull-
ing the steering geor
inside the cor.
6. Slocken the nuts of the bottom wishbone
pins fostening the front oxle to the brocket on
the body until the woshers of the brockets ore
releosed. 7. Detoch the onti-roll bor brockets from
the
body ond disconnect the rubber broke hoses
from the front broke systems.
Before discon-
necting the hose, cleon thoroughly the hose
connector ond its surroundings to prevent
foreign motter from getting
into the broke
system. For the some reoson,
wrop the
hose
ends in o cleon rog. Toke
the some precoutions
with the disconnected broke piping.
8. Ploce o roll-o-cor
iock under the oxle ond
remove the bolts (two
on either side
of the tele-
scopic shock obsorber) fostening the oxle to
the body from obove. 9. Compress the telescopic shock obsorbers,
lower the
iock, ond
move it with the oxle from
under the cor.
6.3 REFITTING FRONT AXLE IN
CAR
1. To reinstoll the oxle in
the cor, reverse the
procedure of its removol, i.
e., begin with the
porogroph 9 ond proceed
to the porogroph
1.
Coot the rubber
cup with greose
ot the point
of its contoct with the steering shoft.
2. While reconnecting the broke hoses, ob-
serve the utmost cleonliness ond bleed the front
wheel brokes if no other ports
of the broke
system hos been dismontled. (lf
such o dis-
montling hos token ploce,
bleed the brokes of
oll wheels ofter hoving fully reclosed
the broke
circuit). 3. Turn the wheels in the stroight oheod di-
rection before connecting the steering shoft
with the steering box. Fit the steering wheel tentotively
ond odiust the direction indicotor
switch -
see Chopter 13.17.
4. Using the steering wheel, tunn the wheels
into full lock positions
to moke sure thot the
lock ongle is correctly limited by the king pin
socket stops -
see Chopter 6.5, porogroph
36.
5. Adiust the toe-in -
see Chopter 6.1.
6.4 DISMANTLING
FRONT AXLE
No speciol instructions ore required for
dis-
montling mony of the subossemblies. Accord-
ingly, only the bosic dismontling procedure
will be
deolth with ond porticulors
will be men-
tioned only os fon
os they ore necessory for the
sequence of operotions ond the use of iigs.
Ports which con be dismontled witlrout re-
moving them from the cor ore the wheel hubs
and beorings, the broke mechonisms, steering
orms, shock obsorbers, ond the
onti-roll bor.
lf ony odditionol ports
hove to be dismontled,
remove the oxle from the cor ond dismontle it
on the stond.
Dismontling Wheel Hubs
ond Beorings
1. Dismontle the broke mechonism os per
Chopter 9.1 ond remove
the wheel hub
cop
using the MP 6-124 drog. When using the MP
6-136 pull-off
cortridge, the hub cop hos to be
prised off with o
tyre lever or o similor tool.
Now remove the costelloted nutwith its wosher
ond pull
out the hub,
ossisting the removol
with
light blows of o mollet, if necessory.
2. Toke out the inner port
of the outer beor-
ing, then the seoling ring, ond, f
inolly, the inner
port of the reor beoring (cone
with topered
rollers). Prise out the seoling ring using o
scrrewdriver. Proceed corefully olong the ring
circumference to ovoid distorting the ring which
Fig. 6.4/1 -
Removing Hub Cop Using
MP 6-124 Drog
106

1
\
I
(
r
t
(
s I
I
(
S
lf
m
gr
lir
O1
sy
ro
po
th
th
th, tir
on
m€
tht
of
onl
I
by tr
Cl
A
6-
tl-
th
th
Fig.6.5/5
-
Pressing-in Beoring Cups Using
MP 6-130 Jig
Fig.6.5/5 -
Instolling Seoling Ring
Using
MP 6-131 Jig 23-
Fit the disk broke bock plote
on the
steering knuckle ond fosten it by bolting down
the broke brocket. Use spring woshers to lock
the bolts. Drive home the wheel hub
on the
steering knuckle with light tops ond use o tube
to top home the beoring cone.
24. Fit the greose-pocked
cone of the outer
beoring on the steering knuckie, locote
the
shim on the beoring, ond tighten the nut with
o torque of 1.5 kpnr (15
Nm) while rototing the
wheel hub.
25. Top
the wheel hub ond the broke disk
with o mollet ond rotote
the wheel hub to bed
in the beorings. Bock off the nut
through obout
-180o
ond retighten it with o torque of obout 5 Nm
(0.5 kpm) while rototing the hub. Then bock off
the nut to the neorest cotter pin
slot (ot
the
most through 30"), ond lock it in this position
by inserting the cotter pin.
26. Check whether the wheel hub rototes
freely br-rt without ony noticeoble
cleoronce in
the beorings, ond secure the nut with the cotter
pin.
Fittirrg Steering Knuckles ond Wheel Hub
into Wishbones
27. Hoving thus ossembled the wheel, instoll
ii into the lower
wishbone, fit
o shim between
tl-re wishbone reor eye ond the resilient bush in
the king pin socket,
threod in the eccentric pin,
cind screw down the nut without tightening it.
28. Press
the wheel ogoinst tlre
upper wish-
borre ond connect it with it
by topping home
the wishbone pin
from the reor side
of the
oxle,
i. e., from the side of the shorter port
of the
king pin
socket. Slip the MP 6-108 pilot
pin
on
the wishbone pin
threod to focilitote threoding
of the pin
through the hole in the wishbone.
Tighten slightly the connection with the costel-
loted nut.
DK ? 2r+
Fig. 6.517 -
MP 6--108 Pilot Pin for
Upper
Wishbone Pin lnstollotion
112