transmission oil SKODA 120LE 1980 Workshop Manual

4.3-4.4
F
I
t
F
i
!
I
r
{.3-4.4
6. Remo
b) Crownwl Tools:
Settin
not le
1. Install
one of the
Glave Cylir
that the p
pendicular
2. Lock
between tl"
cover. 3. Using
back and
clearance I
teeth. This gauge, anc
wheel(see legible the
O.18mm bi
4. lnsuffi
wheel is tc
increase tl
from the nc
the equiva
This will p
increase th
Excess c
thickness
Selector Si
To worl
shims to n
(a) Bac
(b) Act
Refitting C Assembly
29. Instc
ond the rel it with nutr
-looded brc
To
(a) O.3i
(b) o.2r
lf
the shims
connot be set up exoctly to the
colculoted thickness, determine o thickness
which would result
in o prelood
due to on
overoll increose of 0.03 to 0.07 mnr of the di-
rnension of the shims.
27. Ploce the topered roller beoring on the
respective bore, bolt the other MP 5-107
iig on
the housing ond rotote
the centre bolt to press
the beoring into the housing os for os it will go.
Remove the iig, fit the shrunk-on
ring on the
stor pinion,
and lock the ring in position
using
o circlip. Lubricote the beoring with oil, f it the
respective shims on the beoring ond the gosket
on the cover, ond bolt down the cover.
Turn over the housing ond press-in
the other
beoring in the some monner (the press-fitting
iig is olreody in
position),
instoll the preporred
shims, ond bolt down the cover with its gosket.
28. Meosure how deep is tlre drive shoft
beoring below the level of tlre housing
surfoce
ond compensote the difference
with shims up
to o moximum protrrrsion
of 0. I mm -F0.05
rnnr.
Fig.4.3/4 -
Press-f itting of Differentiol Toperecl
Rollr:r Beorings
Using MP 5-107 Jig
Shims 0.1 nrm to 0.2 mm thick ore ovoiloble.
Fit the gosket
ond the ossembled cover on the
housing ond fosten it with nuts ond spring
woshers (for the cover refer
to Chopter 4.5).
Swing down the beoring
with the speedo-
meter drive geors
in the cover into engoge-
nrerrt with the pinion
drive geor
ond lock the
beoring in position
by tightening the nut of the
beoring clip.
Adjusting crownwheel Bearing
Alternative Method a) Crown Wheel Bearing Preload.
Tools Dial Test Gauge and Stand
MPs -
1OG lever Setting:
Preload O.Ob -
O.10 mm
1. Before assembling Transmission casing
remove outer crown wheel bearing races. Leave
the bearings on the
differential housing.
2. Assemble transmission. DO NOT carry out
operation 17
above.
3. Fit the outer races into casing pressing
into
place using coned cover. Do not forget to fit
gaskets. On the Selector Shaft side (side
B) of the
casing fit
approximately O.60 mm of shims
between the coned cover and outer races. Ensure
there is
backlash between crownwheel and
pinion, increase the
shim thickness if required.
4. Fit Dial test gauge
so that pointer
rests on
the differential as shown in fig. 4.3/1A.
5. Lift Crownwheel assembly to determine
clearance between bearings (a).
. . lf this exceeds
O.2O mm decrease the clearance to between O.O1
and 0.20 mm by f itting
shims to Non-selector side
of casing. (b)
. . . When the clearance is between
0.01 and0.20 mm take
a reading. Addtothis0.OS
to 0.10 mm. Make a shim pack
to this thickness
and fit to non-selector side (side
A) of transmission
casing. Check some
backlash still exists between
the Crownwheel and pinion.
Example 1st Dial reading 0.3O mm
0.20 mm
Shim fitted
on non-selector side.
2nd Dial reading 0.07mm
Shim pack
required between
0.07 +O.O5 =O.12mm
and0.O7mm *O.1Omm
= 0.17 mm
Shim sizes available.
0.08, O.14, O.2O and O.SOmm
Shim size selected O.14mm. This
will give
O.07mm preload
tension to crownwheel
beari ngs.
The Crownwheel should now
turn freely with
little drag. Fis.
4.3/1A
82