light SKODA CITIGO 2015 1.G User Guide

MemoryFig. 25
Multi-function display - Display
example of the memory
Read and observe on page 31 first.
The following data will be saved in two memory banks 1 and 2 .
▶ Average fuel consumption.
▶ Distance driven.
▶ Average speed.
▶ Driving time.
The selected memory is displayed at position
A
» Fig. 25 .
“1” - Single-trip memory
The memory collates the driving information from the moment the ignition is
switched on until it is switched off.
New data will also flow into the calculation of the current driving information if
the trip is continued within 2 hours after switching off the ignition.
If the trip is interrupted for more than 2 hours, the memory is automatically
erased.
“2” - Long-term memory
The memory gathers driving information from any number of individual jour-
neys up to a total of 19 hours and 59 minutes driving or 1999 kilometres driven.
The memory is deleted when either of these limits is reached and the calcula-
tion starts all over again.
Unlike the single-trip memory, the total-trip memory is not deleted after a pe-
riod of interruption of driving of 2 hours.
Select memory
Operation » page 31,
▶
Select the desired data to be displayed in the multi-function display.
▶ Confirm details again to select the desired memory.
Reset memory
Operation » page 31,
▶ Select the desired data to be displayed in the multi-function display.
▶ Select the desired memory.
▶ Reset the selected memory by pressing down on it for a long time.
Note
Disconnecting the vehicle battery will delete all memory data.Fig. 26
Buttons in the instrument clus-
ter - variant 1
Read and observe on page 31 first.
The time is set as follows.
›
Select the time display on the instrument cluster » page 31, Operation .
›
Press the button
A
» Fig. 26 and keep it pressed down until the hour display
starts flashing.
›
To change the value, press the button
B
. To change the value quickly, hold
down the button.
›
Press button
A
until it flashes to select the minute display.
›
To change the value, press the button
B
. To change the value quickly, hold
down the button.
›
Confirm the value entered by pressing the button
A
again, or wait for
around 5 seconds. The setting is saved automatically (the value stops flash-
ing).
33Instruments and control lights

Warning lights
Introduction
This chapter contains information on the following subjects:
 Handbrake
34
 Braking system
34
 Seat belt warning light
34
 Alternator
35
 Engine oil pressure too low
35
 Coolant
35

 Automated transmission
35



 
Power steering
36
 Stability Control (ESC) / traction control (ASR)
36
 Antilock brake system (ABS)
36
 Tyre pressure
36
 Rear fog light
37
 Exhaust inspection system
37
 Checking the engine electronics
37
 Airbag system
37

Handbrake - automatic transmission
38
 Brake pedal (automatic transmission)
38

 Turn signal system
38
 Cruise control system
38
 Main beam
38
/
 Rear seat belt warning light
38
 City Safe Drive
38
 /
 START-STOP
38
The warning lights indicate certain functions or faults.
The lighting up of some warning lights may be accompanied by acoustic sig-
nals.
After switching on the ignition, some warning lights light up briefly as a func-
tion test.
If the tested systems are OK, the corresponding warning lights extinguishes
for a few seconds after switching on the ignition or after starting the engine.
WARNING■ Ignoring light-up indicator lamps in the instrument cluster and the control
symbols in the display may cause serious injury or damage to the vehicle.■
If you have to stop for technical reasons, then park the vehicle at a safe
distance from the traffic, switch off the engine and activate the hazard
warning light system » page 49. Place the warning triangle at the prescri-
bed distance.
■
The engine compartment of your car is a hazardous area. The following
warning instructions must be followed at all times when working in the en-
gine compartment » page 106, Engine compartment .
 Handbrake
Read and observe
on page 34 first.
 lights up - the hand brake is engaged.
An audible warning is also given if you drive the vehicle for at least 3 seconds
at a speed of more than 6 km/h.
Braking system
Read and observe
on page 34 first.
 lights up - the brake fluid level in the brake system is too low or there is an
ABS fault.
›
Stop the vehicle, switch off the engine, and check the level of the brake fluid
» page 112 .
WARNING■
If the warning light  illuminates together with the warning light 
» page 36 ,  Antilock brake system (ABS) ,  stop driving! Seek help from
a specialist garage.■
A fault to the ABS system or the braking system can increase the vehi-
cle's braking distance – risk of accident!
 Seat belt warning light
Read and observe
on page 34 first.
 lights up - the driver or front passenger has not fastened their seat belt. 
34Using the system

At a speed of more than approximately 20 km/h the warning light  flashes
and an audible warning sounds at a time.
The warning signal is switched of and the 
indicator light is permanently lit if
the driver and front passenger have not fastened their seat belts within the
next 90 seconds.
 Alternator
Read and observe
on page 34 first.
 illuminates - the battery is not being charged whilst the engine is running.
Seek help from a specialist garage.
CAUTION
If in addition to the symbol  the symbol  » page 35 illuminates while driv-
ing,  stop driving - risk of engine damage! Switch off the engine and seek as-
sistance from a specialist garage.
 Engine oil pressure too low
Read and observe
on page 34 first.
 lights up or flashes - the engine oil pressure is too low.
An audible signal sounds as a warning.
›
Stop the vehicle, switch off the engine, and check the engine oil level
» page 109 , Checking the oil level .
If the warning light  illuminates or flashes, do not drive any further, even if
the oil level is correct! Switch off the engine and seek assistance from a spe-
cialist garage.
CAUTION
■ The oil pressure light  is not an oil level indicator! One should therefore
check the oil level at regular intervals, preferably after every refuelling stop.■
If for some reason, it is not possible to top up the engine oil under the cur-
rent circumstances, 
do not continue driving! Switch off the engine and seek
assistance from a specialist garage.
 Coolant
Read and observe
on page 34 first.
 lights up or flashes - the coolant temperature is too high or the coolant lev-
el is too low.
An audible signal sounds as a warning tone.
›
Stop the vehicle, switch off the engine, and allow the engine to cool down.
›
Check the coolant level, if necessary top up the coolant.
If the coolant is within the specified range, the cooling fan may be malfunc-
tioning.
›
Switch off the ignition.
›
Check the fuse for the cooling fan, replace if necessary.
If the coolant level and fan fuse are both OK but the warning light  is still
illuminated ,

do not drive any further!
Seek help from a specialist garage.
  Automated transmission
Read and observe
on page 34 first.
fault
 lights up - there is a fault in the automatic transmission.
An audible signal sounds as a warning tone.

Do not continue to drive! Switch off the engine and seek assistance from a
specialist garage.
Functional impairment
 lights up and gear change is not possible - for technical reasons there may
be an impairment of the automatic transmission.
›
Stop the car, turn the ignition off and on again.
If the warning light  lights up after you again switch on the ignition, seek as-
sistance from a specialist garage.
Gearbox overheating
 and is possibly also
 illuminated - the automatic transmission is overheat-
ing.
An audible signal sounds as a warning tone. 
35Instruments and control lights

›Stop and allow the transmission to cool down or drive more quickly than
20 km/h (12 mph).
If the warning light 
lights up again, switch off the vehicle, shut off the en-
gine and allow the gearbox to cool down.
Further information » page 81, Automated transmission .
  Power steering
Read and observe
on page 34 first.
  lights up - this indicates a complete failure of the power steering and the
steering assist has failed (significantly higher steering forces).
 
lights up - this indicates a partial failure of the power steering and the
steering forces can be greater.
›
Stop the car, turn the ignition off and on again.
If the indicator light does not illuminate after the engine has been turned on
again, the power steering is fully operational again.
If the warning light illuminates again, then obtain assistance from an author-
ised dealer.
Disconnecting the vehicle battery
If the vehicle's battery has been disconnected and reconnected, the warning
light comes on after switching on the  ignition.
The warning light should go out after driving a short distance.
If, after the motor is restarted and a short drive, the indicator light does not go
out, there is a system error.
Seek help from a specialist garage.
 Stability Control (ESC) / traction control (ASR)
Read and observe
on page 34 first.
 flashes - the ESC or TCS is currently being accessed.
 lights up - there is an ESC or TCS fault.
Seek help from a specialist garage.
As the ESC operates in conjunction with the ABS, the ESC warning light will al-
so come on if the ABS system fails.
If the warning light  comes on straight after starting the engine, the TCS may
be switched off for technical reasons.›
Switch the ignition off and on again.
If the warning light 
does not illuminate after you switch the engine back on,
the ASR is fully functional again.
Disconnecting the vehicle battery
If the vehicle's battery has been disconnected and reconnected, the warning
light comes on after switching on the 
ignition.
The warning light should go out after driving a short distance.
If, after a short drive, the indicator light does not go out, there is a system er- ror.
Seek help from a specialist garage.
More information about the ESC system » page 85, Stability Control (ESC) or
TCS system » page 85, Traction control (TCS) .
Antilock brake system (ABS)
Read and observe
on page 34 first.
 lights up - there is an ABS fault.
The vehicle will only be braked by the normal brake system without the ABS.
Seek help from a specialist garage.
In the event of an ABS fault, the other braking and stabilization systems are
turned off » page 85, Braking and stabilisation systems .
WARNING■
A fault to the ABS system or the braking system can increase the vehi-
cle's braking distance – risk of accident!■
If the ABS warning light 
together with the indicator light 
» page 34
lights, 
do not continue to drive! Seek help from a specialist garage.
 Tyre pressure
Read and observe
on page 34 first.
Change of tyre pressure values
 lights up - there was a pressure change in one of the tyres. 
36Using the system

An audible signal sounds as a warning.›
Immediately reduce speed and avoid sudden steering and braking manoeu-
vres.
›
Stop the vehicle, turn the ignition off and check the tyres and their inflation
pressures » page 117.
›
Correct the tyre pressure if necessary or replace the affected wheel
» page 123 or use the repair kit » page 127.
›
Save the tyre pressure values in the system » page 91.
System fault
 flashes for approximately 1 minute and remains lit - there may be a fault in
the tyre pressure monitoring system.
›
Stop the vehicle, turn the ignition off and start the engine again.
If the warning light  flashes again after the engine has started, there is a
system error.
Seek help from a specialist garage.
Disconnecting the vehicle battery
If the vehicle's battery has been disconnected and reconnected, the warning
light comes on after switching on the  ignition.
The warning light should go out after driving a short distance.
If, after a short drive, the indicator light does not go out, there is a system er-
ror.
Seek help from a specialist garage.
Other incidents
The following reasons can explain the warning light  being illuminated.
▶ The vehicle is loaded on one side. Distribute loads as evenly as possible.
▶ The wheels of one axle are loaded more heavily (e.g. when towing a trailer or
when driving uphill or downhill).
▶ Snow chains are mounted.
▶ A wheel has been changed.
CAUTION
Under certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light  in the instrument cluster can be delayed or does
not light up at all. Rear fog light
Read and observe
on page 34 first.
 lights up - the rear fog light is switched on.
 Exhaust inspection system
Read and observe
on page 34 first.
 lights up - there is a fault in the emission control system. The system allows
the vehicle to run in emergency mode.
Seek help from a specialist garage.
 Checking the engine electronics
Read and observe
on page 34 first.
 lights up - there is a fault in the electronic engine management system. The
system allows the vehicle to run in emergency mode.
Seek help from a specialist garage.
 Airbag system
Read and observe
on page 34 first.
System fault
 lights up - there is a fault in the airbag system.
This also applies if the warning light does not come on when the ignition is
switched on.
The functionality of the airbag system is monitored automatically even if one
of the airbags is switched off.
One of the airbags or a belt tensioner has been disabled by the diagnostic
tool
 lights up for approximately 4 seconds after the ignition is switched on and
then flashes for approximately 12 seconds.
The front passenger airbag has been disabled with the key switch
 lights up for a few seconds when the ignition is switched on. 
37Instruments and control lights

 the lettering     in the middle of the dash panel lights up
after switching on the ignition » page 18, Deactivating the front passenger air-
bag .WARNINGWhen a fault in the airbag system occurs, there is a risk of the system not
being triggered in the event of an accident. Therefore, this must be
checked immediately by a specialized garage.
 Handbrake - automatic transmission
Read and observe
on page 34 first.
 lights up or flashes - engage the parking brake.
Further information » page 81, Automated transmission .
 Brake pedal (automatic transmission)
Read and observe
on page 34 first.
 lights up - apply the brake.
Further information » page 81, Automated transmission .
  Turn signal system
Read and observe
on page 34 first.
 flashes - the left turn signal is turned on.
 flashes - the right turn signal is turned on.
If there is a fault in the turn signal system, the warning light flashes at twice
its normal rate.
When the hazard warning light system is switched on, this will cause all of the
turn signal lights as well as both warning lights to flash.
 Cruise control system
Read and observe
on page 34 first.
 lights up - the vehicle is regulated by the cruise control.
 Main beam
Read and observe
on page 34 first.
 illuminates - the main beam or the headlight flasher is switched on.
/ Rear seat belt warning light
Read and observe
on page 34 first.
 illuminates - a rear seat belt is not fastened.
 illuminates - a rear seat belt is fastened.
When the seat belt is fastened/unfastened, the particular light lights up briefly
and indicates the current belt status!
 City Safe Drive
Read and observe
on page 34 first.
 flashes quickly - City Safe Drivesystem is braking the vehicle automatically.
 flashes slowly - the system is not available or there is a system malfunction.
If the system is turned off and the vehicle is moving at a speed of about 5 - 30
km/h, the warning light 
 illuminates on the instrument cluster display.
If the system is activated again, the warning light 
 
illuminates in the in-
strument cluster display for about 5 s.
Further information » page 89, City Safe Drive .
 /  START-STOP
Read and observe
on page 34 first.
 illuminates - the START-STOPsystem is active.
 illuminates - the START-STOPsystem is active, but the automatic cut off is
not possible.
 flashes - the START-STOPsystem is not available.
Further information » page 77, START-STOPsystem .
38Using the system

Unlocking and opening
Unlocking and locking
Introduction
This chapter contains information on the following subjects:
Unlock / lock using key and lock
40
Unlocking / locking with the remote control key
40
Locking / unlocking the vehicle with the central locking button
40
Safe securing system
41
Opening/closing a door
41
Door opening lever
42
Child safety lock
42
Malfunctions
42
Your car is equipped with a central locking system.
The central locking system allows you to lock and unlock all doors and the lug-
gage compartment lid at the same time.
Depending on the equipment configuration, the following applies after un-
locking.
▶ The turn signal lights flash twice as confirmation that the vehicle has been
unlocked.
▶ All the doors and the boot lid are unlocked.
▶ The interior light comes on.
▶ The Safelock system is switched off.
▶ The indicator light in the driver door stops flashing.
Depending on the equipment configuration, the following applies after lock-
ing.
▶ The turn signal lights flash once as confirmation that the vehicle has been
locked.
▶ All the doors and the luggage compartment lid are locked.
▶ The interior lamp goes out.
▶ The Safelock system is switched on.
▶ The warning light in the driver door begins flashing.
If the doors or the luggage compartment lid remain open after the vehicle has
been locked, the turn signal lights do not flash until they have been closed.
Protection against unintended vehicle unlocking
If you unlock the vehicle and do not open a door or the boot lid within the next
30 seconds, the vehicle will lock again automatically and the Safelock system
will be switched on.
Automatic locking/unlocking
All the doors and the luggage compartment lid are locked automatically once
the car reaches a speed of about 15 km/h.
If the ignition key is withdrawn, the car is then automatically unlocked again. It
is also possible for the driver to unlock the car by pressing the central locking
button.
The vehicle doors can be unlocked and opened at any time by pulling once on
the door opening lever.WARNING■ Never leave the key in the vehicle when you exit the vehicle. Unauthor-
ized persons, such as children, for example, could lock the car, turn on the
ignition or start the engine - there is a danger of injury and accidents!■
When leaving the vehicle, never leave persons who are not completely in-
dependent, such as children, unattended in the vehicle. These individuals
might not be able to exit the vehicle by themselves or to help themselves.
Can be fatal at very high or very low temperatures!
CAUTION
■ Each key contains electronic components; therefore it must be protected
against moisture and severe shocks.■
Keep the groove of the keys absolutely clean. Impurities (textile fibres, dust,
etc.) have a negative effect on the functionality of the locking cylinder and ig-
nition lock.
■
If the driver's door has been opened, the vehicle cannot be locked.
39Unlocking and opening

Unlock / lock using key and lockFig. 27
Left side of the vehicle: Turning
the key for unlocking and locking
the vehicle
Read and observe and on page 39 first.
The key allows you to unlock and lock the vehicle via the lock cylinder in the driver's door.
Unlocking/locking the vehicle with the key » Fig. 27
Unlocking the vehicle
Locking the vehicle
Unlocking / locking with the remote control key
Fig. 28
Remote control key
Read and observe and on page 39 first.
Function and description of the key » Fig. 28
Unlocking the vehicle
Locking the vehicle
Unlocking the boot lid
Button for the extension / retraction of the key
AWarning light for the battery charge status
If the red warning light does not flash when you press a button on the key,
the battery is discharged.
Unlocking / locking the boot lid
By pressing briefly the symbol button 
the boot lid unlocks.
Press and hold the symbol button 
to release the lid (partially opened).
If the lid is unlocked or released with the symbol button 
on the key, then
the lid is automatically locked after closing. You can set a lock delay
» page 43 .
CAUTION
■
The operation of the remote control may temporarily be affected by signal in-
terference from transmitters close to the car and which operate in the same
frequency range.■
The operating range of the remote control key is approx. 30 m. But this range
of the remote control can be reduced if the batteries are weak.
■
The battery must be replaced if the central locking does react to the remote
control at less than around 3 metres away » page 132.
Note
The remote control will operate only when the vehicle is within sight.
Locking / unlocking the vehicle with the central locking button
Fig. 29
Central locking button
Read and observe and on page 39 first.
When the vehicle has not been locked from the outside and no door is open
the button » Fig. 29can be used to unlock or lock the vehicle. 
B40Using the system

Unlocking / locking » Fig. 29
Locking
Unlocking
The central locking system also operates if the ignition is switched off.
The following applies after locking. ▶ Opening the doors and the boot lid from the outside is not possible.
▶ The doors can be unlocked and opened from the inside by a single pull on the
opening lever of the respective door.WARNINGDoors locked from the inside make it difficult for rescuers to get into the
vehicle in an emergency – risk to life!
Safe securing system
Read and observe
and on page 39 first.
As soon as the vehicle has been locked from the outside, the Safelock systemprevents the doors from being opened from the inside.
You will be informed that the safelock system has been activated after the ve-
hicle has been locked by means of the message 
 on the instrument
cluster display.
After locking the vehicle, the warning light in the driver's door flashes for
around 2 seconds in quick succession, afterwards it begins to flash evenly at
longer intervals.
Switching off
▶ The safelock can be switched off by locking twice within 2 seconds.
The indicator light in the driver door flashes for about 2 seconds fast, goes out
and starts to flash at longer intervals after about 30 seconds.
If the vehicle is locked and the safe securing system is switched off, the door
can be opened separately from the inside by a single pull on opening lever.
The Safelock system switches back on when the vehicle is locked.
WARNINGIf the car is locked and the safe securing system activated, no people must
remain in the car as it will then not be possible to either unlock a door or
open a window from the inside. The locked doors make it more difficult for
rescuers to get into the vehicle in an emergency – risk to life!
Opening/closing a door
Fig. 30
Door handle/door opening lever
Read and observe
and on page 39 first.
Opening from the outside
›
Unlock the vehicle.
›
Pull on the door handle
A
in the direction of the arrow » Fig. 30.
Opening from the inside
›
Pull on door opening lever
B
of the door and push the door away from you.
Closing from the inside
›
Grasp pull handle
C
and close the door.
WARNING■ Make sure that the door has closed correctly as it can open suddenly
while driving – risk of death!■
Only open and close the door when there is no one in the opening/closing
range – risk of injury!
■
An opened door can close automatically if there is a strong wind or the
vehicle is on an incline – risk of injury!
■
Never drive with the doors open - there is a risk of death!
41Unlocking and opening

Door opening leverFig. 31
Door opening lever
Read and observe
and on page 39 first.
On vehicles without central locking, you can lock and unlock doors which do
not have a locking cylinder from the inside.
Locking
›
Push the door opening lever in the direction of the arrow so that the red
marking
A
» Fig. 31 is visible.
Unlocking
›
Open the door by pulling the door opening lever once against the direction of
the arrow » Fig. 31 .
Child safety lock
Fig. 32
Rear door: Child safety lock switch on / off
Read and observe and on page 39 first.
The child safety lock prevents the rear door from being opened from the in-
side. The door can only be opened from the outside.
Child safety lock switch on / off » Fig. 32
Switching on
Switching off
You can switch the child safety lock on and off using the vehicle key.
Malfunctions
Read and observe
and on page 39 first.
Central locking fault
If the warning light in the driver's door initially flashes quickly for around 2 sec-
onds, and then illuminates for 30 seconds without interruption before flashing
again slowly, you will need to seek the assistance of a specialist garage.
If there is a fault with the central locking system, only the driver's door can be unlocked or locked with the key. The other doors and the boot lid can be man-
ually locked or unlocked. ▶ Locking the door » page 132.
▶ Unlocking the boot lid » page 133.
Key battery discharged
Replace the battery » page 132.
Luggage compartment lid

Introduction
This chapter contains information on the following subjects:
Opening/closing
43
Delayed locking of the boot lid
43
When closing the boot lid do not press on the rear window.
Ensure that the lock is properly engaged after closing the luggage compart-
ment lid.
The button in the boot lid is deactivated when the vehicle moves off or moves
at a speed above 9 km/h. The function is restored after the vehicle stops and
the door is opened. 

42Using the system