automatic transmission SKODA FABIA 2000 1.G / 6Y Workshop Manual
[x] Cancel search | Manufacturer: SKODA, Model Year: 2000, Model line: FABIA, Model: SKODA FABIA 2000 1.G / 6YPages: 86, PDF Size: 3.58 MB
Page 17 of 86
Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 7 02
Every 60 000 km (QG0)
Includes: Inspection every 30 000 km and additional operations stated in the table below
Every 90 000 km (QG0)
Includes: Inspection every 30 000 km and additional operations stated in the table below
Every 120 000 km (QG0)
Includes: Inspection every 60 000 km and additional operations stated in the table below
Every 150.000 km (QG0)
Includes: Inspection every 60 000 km and additional operations stated in the table below
Work involvedChapter
–Air filter: Clean housing, replace filter element02-3
–Fuel filter: replace (vehicles with diesel engine)02-3
–Ribbed V-belt: Inspect condition and for vehicles without tensioning pulley also the ten-
sion02-3
–Spark plugs: replace02-3
–Automatic gearbox: Inspect ATF1) level, if necessary top up
1)Automatic transmission fluid for the automatic gearbox
02-4
Work involvedChapter
–Timing belt for camshaft drive: replace (ASY diesel engines up to 04.2001)02-3
–Timing belt and tensioning pulley for camshaft drive: replace (PD diesel engine up to
07.03)02-3
–Timing belt for camshaft drive: inspect (petrol engines) - every 90 000 km, then every 30
000 km02-3
Work involvedChapter
–Timing belt and tensioning pulley (038 109 244 H)1) for camshaft drive: replace (diesel en-
gines other than the PD engine) - vehicles as of 05.2001 to 04.2002
1)When the tensioning pulley Spare Part No. 038 109 244 M is mounted after 120 000 km. on vehicles with a diesel engine during replacement of
the timing belt and the tensioning pulley the change interval of the timing belt should be altered from 120 000 km to 150 000 km. The customer
should be informed about the new service interval when the tensioning pulley is first replaced by a new tensioning pulley Spare Part No. 038
109 244 M by making an entry in the service plan, in the section „Workshop entries“. Only the timing belt will be replaced at each next service
interval at 150 000 km.
02-3
–Timing belt for camshaft drive: replace (PD diesel engine as of 08.03)02-3
Work involvedChapter
–Timing belt: replace (diesel engines other than the PD engine) - vehicles as of 05.200202-3
Page 57 of 86
Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 3 02
holding the knob in the left or right position respective-
ly.
Connect vehicle system tester and inter-
rogate fault memory
The stored faults can be read out with vehicle system
tester -V.A.G 1552-, -V.A.G 1551-, or -V.A.S. 5051-.
♦The following description relates to vehicle system
tester -V.A.G 1552- using program card 6.0.
♦The use of vehicle diagnosis, measurement and infor-
mation system -V.A.S 5051- or fault read-out scan
tool -V.A.G 1551- with the program card version 9 is
similar. (A minor deviation on the display read-out is
possible).
Special tools, test and measuring equipment and
auxiliary items required
♦Vehicle system tester -V.A.G 1552 -
♦Diagnostic cable -V.A.G 1551/3, 3A, 3B oder 3C-
Test conditions
•Battery voltage at least 9 V.
•All fuses OK.
•Earth connections between the engine (on gearbox
housing) and body (below the battery) must be O.K.
–Apply handbrake.
–Gearbox: Put the lever into Neutral.
–Automatic gearbox: Move selector lever into position
„P“ or „N“.
–Fold cover open -1- in the direction of the arrow.
Connect vehicle system tester - V.A.G 1552- with appro-
priate cable.
–Start engine and run in idle.
If the read-outs as shown in the work sequence are not
displayed, refer to the following notes:
♦If „Error in data transmission“ is displayed because of
an incorrect entry, unplug cable from vehicle system
tester, plug in again and repeat all the steps.
♦If one of the following messages appears in the dis-
play, carry out fault finding as specified in the fault
finding program at the diagnostic cable ⇒Current
Flow Diagrams, Electrical Fault Finding and Fitting Lo-
cations, or ⇒Operating Instructions of vehicle sys-
tem tester
Note
1552V.A.
G
.H
E
LPQ O C9 8 76 5 43 2 1
Note
Vehicle system test HELP
The control unit does not respond
Vehicle system test HELP
Fault in communication set-up