battery SKODA FABIA 2000 1.G / 6Y Workshop Manual

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Table of ContentsEdition 09.04
S00.5301.14.20II
- Changing brake fluid (every 2 years)...............................................................
- Inspecting the brake fluid level ......................................................................
- Track rod ends: Inspect play, correct attachment and joint boots .............................
- Inspecting tyres (including spare wheel) ...........................................................
- Inspecting the tyre tread depth (including spare wheel) and entering ........................
- Tightening wheel bolts to specific torque ..........................................................
- Inspecting the tyre inflation pressure (including spare wheel) and correcting the tyre
inflation pressure if necessary .......................................................................
Electrical System.......................................................................................
- Power windows: Inspecting positioning ............................................................
- Electrical components: Check for proper operation ..............................................
- Battery: Testing no-load voltage ....................................................................
- Battery: Inspecting electrolyte level, topping up with distilled water if necessary ...........
- Radio: Check for proper operation..................................................................
- Setting clock ............................................................................................
- Connect vehicle system tester and interrogate fault memory..................................
- Resetting service interval display (SID) QG0 .....................................................
- Resetting service interval display (SID) QG1 and QG2 .........................................
- Changing the code of the service intervals ........................................................
- Inspecting headlight beam setting and adjusting if necessary .................................
- Setting the headlight beam ..........................................................................
- Replace emergency battery for alarm system ...................................................
Body.......................................................................................................
- Airbag units: Visual inspection ......................................................................
- Inspect key switch for deactivation of front passenger airbag ..................................
- Check underbody protection and body paintwork for damage .................................
- Inspecting plenum chamber and water drain openings for dirt, cleaning if necessary .....
- Windscreen wiper/washer system: Check for proper operation ................................
- Sun roof: Cleaning and greasing runners .........................................................
- Door locks, locking buttons, child safety locks: Check for proper operation .................
- Replacing the dust and odour filter element ......................................................
- Sticking the vehicle data sticker .....................................................................
- ................................................................................. Inspect trailer coupling
Exhaust-emission Analysis..........................................................................
- Exhaust-Emission Analysis on Models with Fuel Engines ......................................
- Test Values for Exhaust-Emission Analysis on Models with Fuel Engines..................
- Exhaust-Emission Analysis on Models with Diesel Engines ....................................
- Test Values for Exhaust-Emission Analysis on Diesel Engines................................
Miscellaneous...........................................................................................
- Tow starting/Towing ..................................................................................
- Perform a test drive ...................................................................................
- Raising the vehicle ....................................................................................02-5page 2
02-5page 4
02-5page 5
02-5page 5
02-5page 6
02-5page 6
02-5page 6
02-6page 1
02-6page 1
02-6page 1
02-6page 1
02-6page 2
02-6page 2
02-6page 2
02-6page 3
02-6page 4
02-6page 7
02-6page 9
02-6page 10
02-6page 12
02-6page 13
02-7page 1
02-7page 1
02-7page 2
02-7page 2
02-7page 3
02-7page 3
02-7page 4
02-7page 4
02-7page 5
02-7page 6
02-7page 6
02-8page 1
02-8page 1
02-8page 2
02-8page 5
02-8page 6
02-9page 1
02-9page 1
02-9page 2
02-9page 2

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
General pointsEdition 09.04
S00.5301.14.2002-1 page 3 02
Vehicle data sticker
The vehicle data sticker is located at the rear left on the
floor of the boot.
Storage of ŠKODA new vehicles
Notes on storage of new vehicles ⇒Technical Service
Handbook.
Vehicle handover from stock
–Before starting a stock vehicle, carry out a Pre-sales
Inspection.
–If the vehicle has been in stock for more than 6
months, replace the brake fluid.
–Inspect the electrolyte level of the battery and top up,
if necessary.
–Before the vehicle is sold, the recharging table must
be removed from the battery.
–If the battery is more than 52 weeks old or has been
recharged more than twice, it must be replaced with
a new battery.
Additional customer information regard-
ing inspection and maintenance
Information regarding the use of vehicles under
„severe conditions“:
–The service advisor should always point out to the
customer that the inspection intervals are based on
normal operating conditions.
–Under „severe conditions“ the inspection intervals
must be shortened.
„Severe conditions“ exist, for instance, if the vehicle is op-
erated continuously in one or several of the conditions
stated below:
♦Towing a trailer or when fitted with a roof rack.
♦Operated on dusty, poor, muddy roads or roads treat-
ed with road salt.
♦Driven for short distances and at ambient tempera-
tures below freezing point.
–If one or several of these „severe conditions“ exists,
please advise your customer whether it is necessary
to have work carried out between the normal service
intervals, such as:
♦Changing the engine oil before the normal specified
interval.
♦Cleaning or replacing the air filter element in the air fil-
ter housing.

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 1 02
02-2 Inspection
Pre-Delivery Inspection -PDI- (Export)
The operations marked with * apply to all countries; other
operations are applicable to certain countries only!
Compare as-delivered condition of vehicle with order form Chapter
♦Engine fitted
♦Type plate in the engine compartment
♦Vehicle data sticker (compare with stamped identification number)
♦Colour of paintwork, badges, inscriptions
♦Seats (cover, colour) interior trim (colour)
♦Radio, speakers, aerial
♦Central locking system, anti-theft alarm system
♦Wheels, tyres
♦Sun roof
♦Vehicle log book - for completion: Operating manual and service plan (in the correct lan-
guage and with the correct edition data), short introduction, technical data, support in the
case of a breakdown, other manuals (radio,...) ) - all in the vehicle log book pouch
♦Other equipment (all equipment fitted in proper condition)
* Check transport damage (bodywork, paintwork, upholstery, interior trim, carpeting, footmats,
tyres, wheels)02-5, 02-7
Vehicle (exterior)
–Check that all car keys and key number fobs have been provided; check that the sticker
for the key number for the electronic immobiliser is complete and legible
–Proper operation of door handles outside, door locks, child safety locks, door contact
switches and proper operation of all locks and keys (including spare keys), doors, boot lid/
tailgate, fuel filler cap, bonnet lock02-7
–Proper operation of anti-theft alarm system
Engine compartment (from above)
–Check battery no-load voltage, recharge battery if necessary02-6
–Check tight connection of electric cables and plug connections (in particular battery ca-
bles)
–Inspect engine, gearbox, cooling system, brake system and fuel system for leaks02-3, 02-5
–Engine oil level (in-between markings on dipstick)02-3
–Brake fluid level (at „MAX“ marking)02-5
–Coolant level (in-between marking), special equipment antifreeze down to -35°C02-3
–Fill up fluid in washer reservoir, in the winter add antifreeze
Vehicle interior
–Proper operation of seat belts, seat belt height adjuster, power windows and sun roof
–Check car tool kit, spare wheel and accessories for completeness and proper attachment
Underside of vehicle (on lift platform)
–Inspect underbody (underbody protection for damage)02-7
–Inspect for leaks and damage: Engine, gearbox, final drive, steering, brake system, axles,
joint boots. Check proper routing of the brake hoses and brake lines, fuel lines including
ventilation of the fuel system02-3, 02-5

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 2 02
Pre-sales Inspection - (the Czech Republic)
Compare as-delivered condition of vehicle with order form Chapter
♦Engine fitted
♦Type plate in the engine compartment
♦Vehicle data sticker (compare with stamped identification number)
♦Colour of paintwork, badges, inscriptions
♦Seats (cover, colour) interior trim (colour)
♦Radio, speakers, aerial
♦Central locking system, anti-theft alarm system
♦Wheels, tyres
♦Sun roof
♦Vehicle log book - for completion: Operating manual and service plan (in the correct lan-
guage and with the correct edition data), a list of dealers, short introduction, technical da-
ta, other manuals (radio......) ) - all in the vehicle log book pouch
♦Other equipment (all equipment fitted in proper condition)
♦Vehicles in stock for more than 6 months: Change brake fluid
Inspections and operations to be completed
Vehicle (exterior)
–Plastic and rubber parts - cleanliness and damage
–Inspect bodywork and paintwork for damage02-7
–Check that all car keys and key number fobs have been provided; check that the sticker
for the key number for the electronic immobiliser is complete and legible
–Proper operation of door handles outside, door locks, child safety locks, door contact
switches and proper operation of all locks and keys (including spare keys), doors, boot lid/
tailgate, fuel filler cap, bonnet lock02-7
–Proper operation of anti-theft alarm system
–Tighten the wheel bolts to specified torque (steel and light alloy wheels 120 Nm), fit wheel
caps02-5
–Check the tyre inflation pressure (including spare wheel), if necessary correct the tyre in-
flation pressure, fit valve caps02-5
–Fit roof aerial
Engine compartment (from above)
–Check battery no-load voltage, recharge battery if necessary02-6
–Check tight connection of electric cables and plug connections (in particular battery ca-
bles)
–Inspect engine, gearbox, cooling system, brake system and fuel system for leaks02-3, 02-5
–Engine oil level (in-between markings on dipstick)02-3
–Brake fluid level (at „MAX“ marking)02-5
–Coolant level (in-between marking)02-3
–Fill up fluid in washer reservoir, in the winter add antifreeze
–Windscreen wiper/washer system and headlamp cleaning system: Check for proper oper-
ation02-7
Vehicle interior

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 4 02
–Fit roof aerial
Engine compartment (from above)
–Check battery no-load voltage; recharge if necessary02-6
–Check tight connection of electric cables and plug connections (in particular battery ca-
bles)
–Brake fluid level (at „MAX“ marking)02-5
–Check the engine oil level (to be in-between the marking on the dipstick)02-3
–Check the coolant level (in-between marking), for special equipment antifreeze down to -
35 °C02-3
–Fill up fluid in washer reservoir, in the winter add antifreeze
–Check windscreen wiper and washer system, the spray nozzle adjustment and the resting
position of the windscreen wipers02-7
Vehicle interior
–Inspect upholstery, interior trim, carpeting and footmats for cleanliness and damage
–Inspect all switches, all electrical components, gauges/indicators and controls02-6
–Radio: Inspect for proper operation, store stations, encode, set clock02-6
–Fit net in luggage compartment (if available)
–Vehicle log book - for completion: Operating manual and service plan (in the correct lan-
guage and with the correct edition data), short introduction, technical data, support in the
case of a breakdown, other manuals (radio,...) ) - all in the vehicle log book pouch
–Reset service interval display02-6
–Power windows: Inspecting positioning02-6
–Key switch for airbag deactivation, front passenger side: Check function „ON/OFF“ and
switch-over to the position „ON“02-7
Underside of vehicle (on lift platform)
–Inspect underbody (underbody protection for damage)02-7
–Inspect for leaks and damage: Engine, gearbox, final drive, steering, brake system, axles,
joint boots. Check proper routing of the brake hoses and brake lines, fuel lines including
ventilation of the fuel system02-3, 02-5
–Inspect tyres and wheels for damage02-5
Concluding operations
–Perform a test drive02-9
–Interrogate fault memory of all systems, if necessary erase02-6
–Complete the service schedule, affix the vehicle data sticker in the Service Schedule to
the floor of the luggage compartment next to the spare wheel, complete the „Next Service
Date“ sticker and affix to the side of the dash panel on the driver's side02-7
–Remove recharging table (if affixed)
–Remove protective seat covers
–Install the carpets supplied in the vehicle
–Final inspection to ensure proper condition for handover to customer

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 5 02
Oil Change Service every 15.000 km1) (QG0)
An Oil Change Service need only be carried out if the vehicle has covered 15 000 km before one year has
elapsed1). If the Oil Change Service is due only a few months prior to the Annual Inspection, it is recommend-
ed to carry out the Annual Inspection at the same time.
Annual Inspection (every 12 months) (QG0)
1)The 7500 km interval applies for diesel operation with high sulphur content - it does not apply for the Czech Republic (for further information
refer to Technical Service Handbook)
Work involvedChapter
–Change engine oil
–Replace engine oil filter02-3
–Disc brake pads: Inspect thickness02-5
–Reset service interval display02-6
–Drain away water from the fuel filter (diesel engine with fuel operation, which does not
comply with DIN EN 590-standard)
After each oil change
–Complete „Next service date“ sticker (max. 1 year or 15 000 km) and affix sticker to the
side of the dash panel (on the driver's side)
–Complete and attach service mirror tag to the interior rear-view mirror
–Hand customer the completed and signed form
Chapter
♦For vehicles with a high mileage carry out an Oil Change Service no later than after 15
000 km1). Carry out Annual Inspection after 30 000 km prior to the scheduled date02-3
♦Every 2 years - in addition change brake fluid 02-5
♦Every 4 years - in addition, change air filter element and clean air filter housing - vehicles
driven less than 60 000 km within 4 years - replace contents set for tyre repair 02-3
♦Every 5 years - replace the emergency battery for the alarm 02-6
♦Exhaust-emission analysis (EEA): Expiry date - see EEA tag on the vehicle identification
plate (only valid for some countries)
♦Recommendation: Replace windscreen wiper blades every 2 years
♦At each inspection - check the 'use by date' of the first aid kit
Work involved
–Interrogate fault memory of all systems, if necessary erase02-6
–Inspect engine and components in the engine compartment for leaks and damage02-3
–Change engine oil
–Replace engine oil filter02-3
–Airbag units: Perform visual inspection for external damage02-7
–Reset service interval display02-6
–Inspecting brake system for leaks and damage02-5
–Check the thickness of the brake pads on all wheels02-5
–Check gearbox, final drive, drive shafts and joint boots for leaks and damage
–Axle joints: Inspect boots for leaks and damage

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 6 02
Every 30 000 km (QG0)
Includes: Annual inspection and additional operations stated in the table below
–Track rod ends: Inspect play and correct attachment of boots
–Check the tyre inflation pressure (including spare wheel), correct if necessary02-5
–Inspect tyre wear (including spare wheel)02-5
–Inspect tyre tread depth (including spare wheel) and record (FL..., FR..., RR..., RL...,
SP...)02-5
–Inspect exhaust system for leaks, damage and attachment
–Brake fluid volume: Check level, if necessary top up02-5
–Battery: test02-6
–Check the anti-freeze in the cooling system and record ...... °C, check for leaks, top up
coolant if necessary02-3
–Flap lock for the engine bonnet: grease
–Inspect operation of all switches, all electrical components, gauges/indicators and con-
trols for proper operation02-6
–Windscreen wiper and washer system: Inspect condition of wiper blades, wiper opera-
tion, washer system: if necessary top up fluid02-7
–Inspect plenum chamber for dirt, clean if necessary02-7
–Fuel filter: Drain away water (vehicles with diesel engine with fuel operation, which does
not comply with DIN EN 590-standard)02-3
–Inspect trailer coupling (with removable arm - manufacturer Profsvar)02-7
After each inspection
–Complete the „Next Service“ sticker and affix sticker to the side of the dash panel (on the
driver's side)
–Perform road test including inspection of proper operation of footbrakes and handbrake,
gearshift and steering, final inspection02-9
–„Mirror tag“ - complete and attach to interior mirror
–Hand customer the completed and signed form
Work involvedChapter
–Headlights: Inspect, if necessary adjust02-6
–Gear oil: Inspect level and top up if necessary (manual gearbox)02-4
–Fuel filter: Drain away water (vehicles with diesel engine with fuel operation, which does
not comply with DIN EN 590-standard)02-3
–Check underbody protection and body paintwork for damage02-7
–Dust and odour filter element for the passenger compartment: replace02-7
–Inspect operation of tilting roof and grease the runners02-7
–Inspect timing belt (petrol engines) - every 90 000 km, then every 30 000 km02-3

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 9 02
–Check the tyre inflation pressure (including spare wheel), correct if necessary02-5
–Inspect tyre wear (including spare wheel)02-5
–Inspect tyre tread depth (including spare wheel) and record (FL..., FR..., RR..., RL...,
SP...)02-5
–Inspect exhaust system for leaks, damage and attachment
–Brake fluid volume: Check level, if necessary top up02-5
–Battery: test02-6
–Check the anti-freeze in the cooling system and record ...... °C, check for leaks, top up
coolant if necessary02-3
–Flap lock for the engine bonnet: grease
–Inspect operation of all switches, all electrical components, gauges/indicators and con-
trols for proper operation02-6
–Windscreen wiper and washer system: Inspect condition of wiper blades, wiper operation,
washer system: if necessary top up fluid02-7
–Inspect plenum chamber for dirt, clean if necessary02-7
–Inspect operation of tilting roof and grease the runners02-7
–Headlights: Inspect, if necessary adjust02-6
–Gear oil: Inspect level and top up if necessary (manual gearbox)02-4
–Draining the fuel filter (diesel engine)
–Inspect trailer coupling (with removable arm - manufacturer Profsvar)02-7
–Check underbody protection and body paintwork for damage02-7
–Dust and odour filter element for the passenger compartment: replace02-7
–Air filter: Clean the housing, replace the insert every 4 years or 60.000 km.02-3
–Replace the fuel filter (diesel engine with fuel operation, which does not comply with DIN
EN 590-standard)
–Ribbed V-belt: Inspect condition and for vehicles without tensioning pulley also the ten-
sion - every 60.000 km02-3
–Replace the fuel filter (diesel engine) - every 60.000 km
–Spark plugs: replace - every 60.000 km.02-3
–Automatic gearbox: Check the ATF level, and top up if necessary, every 60.000 km
–Check the timing belt for the camshaft on a 4-cylinder petrol engine at 90.000 km and
then every 30.000 km after that
–Replace the emergency battery for the alarm system - every five years02-6
After each inspection
–Complete the „Next Service“ sticker and affix sticker to the side of the dash panel (on the
driver's side)
–Perform road test including inspection of proper operation of footbrakes and handbrake,
gearshift and steering, final inspection02-9
–„Mirror tag“ - complete and attach to interior mirror
–Hand customer the completed and signed form Work involvedChapter

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 1 02
02-6 Electrical System
Power windows: Inspecting positioning
If the battery is diconnected the power windows forget
their current position.
Test conditions:
•All car doors closed
The inspection procedure is carried out from the outside
Close window with the car key using the convenience
closing system.
–Turn car key into close position and hold until all the
windows are closed.
–After closing the windows hold the key in the close po-
sition for approximately another 3 seconds.
Electrical components: Check for proper
operation
–Inspect lighting, main headlights, headlight beam con-
trol, fog lights, turn signal lights, hazard warning light
system, tail lights, rear fog lights, reversing lights,
brake lights, parking light control for brightness and
proper operation.
–Inspect interior lights, illuminated storage compart-
ment, illuminated ashtray for proper operation.
–Airbag warning lamps: Check operation ⇒Chapter
02-7.
–Inspect warning buzzer, onboard computer, all switch-
es in centre console as well as on the dash panel and
horn for proper operation.
–Inspect power windows, exterior mirrors (heated and
electrically adjustable), central locking system, infra-
red remote control and convenience closing system
for proper operation
–Inspect heating of front seats for proper operation.
–Inspect radio for proper reception and absence of in-
terference, also inspect speakers ⇒02-6 page 2.
Battery: Testing no-load voltage
Special tools, test and measuring equipment and
auxiliary items required
♦Multimeter (e.g. -V.A.G 1526 A-)
Prior to the measurement the vehicle must have been in
the no-load state for at least two hours (no engine starts,
no charging or discharging of battery).
The following procedure applies to measuring the battery
voltage in the no-load state (after at least two hours):
–With the battery installed measure the voltage be-
tween the terminals (ignition switched off).

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 2 02
If the tester indicates a voltage of 12.5 Volts or more, the
battery is O.K.
If the voltage is less than 12.5 Volts determine the cause
(repair measure).
Battery: Inspecting electrolyte level, top-
ping up with distilled water if necessary
This procedure is not valid for batteries with the sign
„Magic eye“. Test procedure for these batteries
⇒Electrical System; Rep. Gr. 27.
–Inspect electrolyte level:
–The electrolyte level must be between the „MIN“ and
„MAX“ markings.
–Top up the battery with distilled water up to the „MAX“
marking if necessary.
Before disconnecting the battery determine the code of
radio sets fitted with anti-theft coding.
Radio: Check for proper operation
Precise information on how to operate the radio should
be obtained from the operating instructions before in-
specting proper operation of the radio set.
–Switch radio set on and off.
–Operate the volume control.
–Carry out station programming1).
–Inspect station search1).
–Inspect cassette player (insert cassette and play) 1).
–Inspect activation of the anti-theft code of the radio 1).
Setting clock
A rotary knob is provided next to the rev counter for set-
ting the time. The hours (h) are set by turning the knob -1-
to the left, and the minutes (min) are set by turning the
knob to the right:
–By briefly turning the knob the time is advanced by
one hour or one minute. It is possible to move the
hours or minutes back or forward continuously by
Note
WARNING!
When working on the battery wear proper protec-
tion and observe safety precautions.
1)These functions are model specific and are not present on all types of radio sets. For operation refer to Radio Operating Instructions.
Note
S02-03061