display SKODA FABIA 2004 1.G / 6Y MS202 Car Radio Manual

GB
BRIEF OPERATING INSTRUCTIONS
3
Pos. ................................................... Page
1– Tone control .................................... 6Press the tone control buttons and
turn the control knob/push button
6
to change the setting.
– 1 pressure: bass control (BASS)
– 2 pressures: treble control (TRE)
2– Tone balance button ........................ 7 Press the tone balance button and
turn the control knob/push button
6to
change the setting pressures:
balance (BAL)
3– Station buttons ................................. 9 for 12 FM and 12 AM stations.
4– A/F button ......................................... 6 This button serves for switching over
between FM 1/2 and AM 1/2 mode.
5– TP/Set button ................................. 10 Briefly pressing this button switches
on the traffic programme functions.
Pressing this button a longer time dis-
plays the Setup menu.
Pos. ................................................... Page
6– Control knob/push button ................. 5
– Switch on/off: press the button.
– Volume control: turn the knob.
– Tone control: press the tone control button
1then turn the control knob.
– Tone balance: press the tone balance button
2then turn the control knob.
9– Cassette compartment ................... 12
ß`– Cassette ejection ............................ 12
ßQ– Station search rocker ...................... 8Briefly press the rocker to start a sta-
tion search cycle in the AM range.
When in the FM range, you can scroll
through the memory list.
Pos. ................................................... Page
Display
7– TP indication .................................... 2
8– Wavebands ...................................... 2
ßI– Station buttons indication ................. 2
ß?– Station name .................................... 2

GB
Control knob/push button
5
6– Control knob/push button
This knob/button permits:
• Switching on/off the radio
• Volume control
• Tone control
• Tone balance control
AUDGEO11
Switching on/off,
volume control
Pressing the push button 6switches
the radio on and off.
The frequency and volume adjusted befo-
re switching off are recovered.
If the ignition key is removed from the igni-
tion lock with the radio switched on, the
radio is automatically switched off.
If the ignition key is refit into the ignition
lock and turned, the radio is automatically
switched on.
If the ignition key is pulled out, you may
switch on the radio by pressing the control
knob/push button
6twice.
After about 1 hour the radio is automati-
cally switched off to avoid discharging of
the car battery.
You may repeat this operation as often as
desired.
If the car radio remains mute after switch-
ing on and "SAFE" appears in the display,
observe the notes from page 16.
Turning the control knob
6allows you
to change the volume, the tone or the tone
balance settings.
AUDGEO11
RADIO MODE
66

Bass control (BASS)
• Press the AUD button
1. "BASS" and
the current setting + 6 to – 6 appear in the
display.
• Turn the control knob/push button
6to
the left or the right to adjust the desired
setting.
• If you wish to adjust the bass control immediately to its centre setting, press
the AUD button
1until "BASS 00"
appears in the display.
• When this is done, press the AUD button
1again to store the setting. This will sel-
ect at the same time the treble control
mode.
RANGE SELECTION BUTTONTone control
6
RADIO MODE
4– A/F button
Use the A/F button 4to switch between
the "FM" and "AM" ranges.
Press the A/F button
4repeatedly to
switch between the memory levels "FM1"
and "FM2" or “AM1“ and “AM2“.
The display shows "FM1" or "FM2" for the
memory levels in the FM range, and
"AM1" or "AM2" for the memory levels in
the AM range.
TP6A/FA/F4
1– Tone control button
After pressing the AUD button 1, the fol-
lowing indications appear in the display:
• 1 pressure: bass control "BASS",
• 2 pressures: treble control "TRE".
You may change the tone control setting
by turning the control knob/push button
6.
AUDGEO11
TP
AUD1
6

Treble control (TRE)
• "TRE" and the current setting + 6 to – 6appear in the display
• Turn the control knob/push button
6to
the left or the right to adjust the desired
setting.
• If you wish to adjust the treble control immediately to its centre setting, press
the AUD button
1until "TRE 00"
appears in the display.
• When this is done, press the AUD button
1again to store the setting.
• To go directly to the treble control mode, press the AUD button
1briefly twice.
7
GB
Tone control Tone balance control
Balance (BAL)
With this function you may adjust the volu-
me balance of the left/right loudspeakers.
• "BAL" and the current setting (from LEFT
15 via CENTER to RIGHT 15) appear in
the display.
•Turn the control knob/push button
6to
the left or the right to adjust the desired
setting.
• If you wish to adjust the Balance control immediately to its centre setting, press
the GEO button
2until "CENTER"
appears in the display.
• When this is done, press the GEO button
2again to store the setting.
• To go directly to the balance control mode, press the GEO button
2briefly.
RADIO MODE
2– Tone balance button
After pressing the tone balance button
GEO
2, the following indications appear
in the display:
• Balance (BAL)
Turn the control knob/push button
6to
the left or the right to adjust the desired
setting.
AUDGEO11
TP
GEO
6
2

First press the A/F button 4repeatedly to
select one of the memory levels of the
"FM1", "FM2", "AM1" or "AM2" ranges.
ßQ– Station search rocker
Press on
or of the rocker ßQto start
the manual station search.
• Briefly press one side of the rocker
ßQ:
"MAN" and the current reception fre-
quency appear in the display.
TP6A/FA/F
8
Manual tuning
RADIO MODE
• Briefly press repeatedly on
or of the
rocker
ßQ:
The frequency is changed in single steps
(50 kHz steps in FM, 1 KHz steps in
AM).
• Hold down

or of the rocker ßQ:
the frequency scrolls at high speed.
13
4

Manual storing
• Press the station button 3on which the
station is to be stored until the mute
function is deactivated (the frequency to
be stored appears in the display). The
station is stored.
Please make sure that the station name
is shown while the station is stored and
not a moving text as otherwise the
moving text will be stored instead of
the station name.
9
GB
Manual storing Station buttons
You may store up to 24 stations on the 6
station buttons in connection with the res-
pective memory levels.
FM1/FM2 range = 6 stations each
AM1/AM2 range = 6 stations each
"FM2" means that you are in the second
memory level. Press the A/F button
4to
switch between the memory levels.
1123456
TP
123456
RADIO MODE

11
GB
When storing RDS stations you should
press the corresponding station button
only when the station name appears in
the display. This ensures that all RDS
information has been interpreted and
stored automatically.
When calling up stored RDS stations,
the corresponding station name is display-
ed. If the stored frequency is too weak for
good reception, the radio searches auto-
matically for an appropriate alternative fre-
quency (best station function).
If non of the stored alternative frequencies
is strong enough for good reception, the
desired station cannot be received at the
moment. In this case, tune to another sta-
tion.

!Please make sure that the station
name is displayed when the station
is stored. If a moving text should be
displayed, this will be stored
instead of the station name.
In many European countries, RDS is al-
ready transmitted by many radio stations.
The goal is to provide an overall coverage.
With this system, an inaudible digitized
data current is transmitted in addition to
the normal FM radio signal, providing the
RDS receiver with information in encoded
form which controls, among other things,
the following functions:
• Programme identification (PI code)
With the help of the PI code, the radio
recognizes the currently received station.
• Programme service name (PS code)
The PS code transmits the station name
which is shown in the display.• Alternative frequencies (AF code)
Because of the limited transmission range
of the FM waves, the programme of one
radio provider is transmitted by several
stations on different frequencies. The AF
code informs the radio about all alternative
frequencies of the same programme.
This enables the radio to tune to the fre-
quency which can be received in the best
quality.
Tuning to another frequency is carried out
in an inaudible way.
The station name in the display remains
unchanged.
While you are driving, the RDS radio sear-
ches permanently for alternative frequen-
cies of the station selected and tunes to
this in an automatic and inaudible way.
• Traffic programme identification (TP code = Traffic programme)
This information tells the radio that it is
currently receiving a traffic programme
station.
Information about How does RDS work?
RDS stations
RADIO MODE

12
When the TP function is activated during
cassette mode, cassette play is automati-
cally interrupted during a traffic announce-
ment so that this can be heard.
If the transmission range of the traffic sta-
tion tuned to is left, the radio will automati-
cally search a new traffic radio station.
Briefly press the TP button
5if you wish
to abort a traffic announcement and to
continue cassette play.
A new traffic announcement is heard
again.
Insert the cassette fully into the cassette
compartment. When inserting a cassette,
the radio switches automatically to cas-
sette play.
CASSETTE MODE
Cassette compartment Fast forward and rewind Cassette mode and traffic
radio programmes
ß`Fast forward and rewind
Pressing the button ß`selects fast
rewind or forward, respectively.
“WIND” appears in the display.
Briefly pressing the button
ß`ends the
fast forward or rewind function
Cassette ejection
• Press and hold down the button ß`
during cassette play to eject the cassette
(motor ejection).
3456
12

13
GB
The Setup menu
Pressing the TP button 5for more than 2
seconds enables you to carry out special
settings and special RDS functions.
To select the individual Setup menu items,
use the two rockers (see pos.
or 
and ßQ).
It is possible to select the following menu
functions.
• TAVOL
• LRN
• REG
• ONVOL
• IGN
• CODE/SAVE
Exit the Setup menu
Press the TP button
5or make no adjust-
ment for more than 30 seconds to save
your changed settings and to exit the
Setup menu.
TAVOL
The TAVOL function enables you to adjust
the minimum volume for traffic announce-
ments.
If the current volume is lower than the
TAVOL setting, the volume of the traffic
announcement will be increased to the
TAVOL setting.
• Select TAVOL in the setup menu. "SETUP TAVOL" and the current setting
appear in the display.
• Use the control knob/push button
6to
select the desired setting. The setting
range is 04 – 20. LRN ON/OFF
If you are driving in a region where the
reception of RDS programmes with traffic
announcements is poor, you may prevent
the automatic station search in radio
mode.
"LRN ON" automatic LEARN desired,
"LRN OFF" automatic LEARN not
desired.
• Press

or of the rocker ßQto select
the desired setting.
SETTINGS

14
IGN ON/OFF
Switching on and off with the ignition
switch.
"IGN ON" You may switch the car radioon and off with the ignition
switch of the vehicle.
"IGN OFF" You may switch the car radio on and off only with the "IO"
button.
• Press

or of the rocker ßQto select
the desired setting.
CODE/SAVE
If "CODE" appears in the display, coding
is not activated.
If "SAFE" appears in the display, coding is
activated.
The way how to activate and deactivate
the coding is described on the the follow-
ing pages.
REG ON/OFF
If the reception quality gets poor, your car
radio first only selects an alternative fre-
quency of the current station.
However, if the reception quality gets so
poor that a lose of the station becomes
possible, the radio will also accept fre-
quencies of a “related” station.
The "REG ON/REG OFF" function ena-
bles you to select whether alternative fre-
quencies with identical programme are to
be tuned to with the help of the RDS sig-
nal, that is, regional stations are only
selected in the case of emergency.
• Select REG ON/REG OFF in the Setup menu.
"SETUP" and the current setting are dis-
played. The "REG ON" setting is preset
at the factory.
• Press

or of the rocker ßQto select
the desired setting.
REG OFF: free change between all regio-
nally related stations.
REG ON: preferred change between identi-
cal programmes; in the “case of emergen-
cy” also change to a regional programme.
ONVOL
With the ONVOL function you may limit
the maximum switch-on volume.
Normally the last adjusted volume will be
recovered when switching the car radio
on. However, if the switch-off volume is
higher then the ONVOL setting, the
switch-on volume will automatically be
limited to the ONVOL setting.
• Select ONVOL in the Setup menu. "SETUP ONVOL" and the current setting
appear in the display.
• Use the control knob/push button
6to
select the desired setting. The setting
range is -- – 47.
SETTINGS