tow SKODA OCTAVIA 2007 1.G / (1U) Nexus Navigation System Manual

Radio/CD/Sound
12Sound, sound focus and volumeThis section describes how the sound character and the
volume of different sound sources can be set individually.
– Press the button Ÿpage 2, fig. 1 to open the Sound
main menu.Function keys in Sound main menu:
or – Treble or Bass settings Ÿfig. 11
3) – Volume setting for the mid-range frequencies
– Sound focus setting left/right
– Sound focus setting front/rear – Opens the volume set-up where individual volume settings can
be made for the different audio sources Ÿfig. 12 .
Function keys in the volumes set-up function: – The setting for the sensitivity of the speed-dependent volume
adjustment (GALA). The volume of the audio source will be increased
automatically by GALA as the road noise increases at higher speeds. The
volume will be increased more the further the control is set towards the
right.
– Minimum volume for traffic announcements – Minimum volume for telephone conversations
– Minimum volume for navigation system announcements – The traffic announcements are muted as long as a orange
bar can be seen next to the function key.
– Sets the minimum volume for when the unit is switched on.Note
By pressing buttons Ÿpage 2, fig. 1 , and status button
at the same time, you can reset the radio navigation system to the
R F
Bass
back with ESC
TrebleSound RADIO
VolumeBra-0035
Fig. 11 Sound main
menu
Initial volumeVolume set-up
back with ESC
NAV mute
Telephone
NAV min
TA min
GALA
Bra-0036
Fig. 12 Volume
settings
3)Vehicles with a sound system
Š
A3
Treble
Bass
MidBalanceFaderVolu meGALATA M i nTelephoneNAV MinNAV muteInitial volume
Š
A3
TELE
A15
A10
sao.book Seite 12 Montag, 22. M‰
rz 2004 9:32 09

Navigation
14Navigation OverviewHow does the navigation system work, and how is it operated?
An optimal route is defined using sensors, satellites and
traffic reports and the driver is then guided to his or her
destination.The current vehicle position is determined using a system of satellites
(GPS - Global Positioning System). Sensors in the vehicle measure
distances that have been driven. Measured values are compared using
the detailed map material on the navigation CD and corrected with the
assistance of TMC traffic announcements as necessary. An optimal route
to the destination is determined in this way.
Navigation announcements and direction arrows shown on the screen
and in the combi-instrument guide you safely and conveniently to your
destination. You can drive to a given address in towns you are unfamiliar
with, or drive to the nearest garage or be guided to a hotel.
In this chapter, answers can be found to the following questions:x
What rules do I have to keep to when using the navigation system?
Ÿ page 14, “Safety”
x
How do I use the navigation CD? Ÿpage 15, “The navigation CD”
x
Can I listen to music when using the navigation system? Ÿpage 15,
“General notes”
x
What happens if I leave the recommended route? Ÿpage 15,
“General notes”
x
Can a navigation announcement be repeated? Ÿpage 39,
“Announcement of navigation recommendations”
x
How does the radio navigation system respond when driving in an
underground car park or a tunnel? Ÿpage 15, “General notes”
x
How do I enter destinations? Ÿpage 17, “Destination entry”
x
How can I enter garages, restaurants or hotels as destinations?
Ÿ page 21, “Special destinations close to the address”
x
Can I store destinations in a memory? Ÿpage 23, “Destination
memory”
x
What parameters can I set for route calculation? Ÿpage 27, “Param-
eters for route calculation”
x
What can I see on the screen? Ÿ page 32, “Map and symbol displays”
x
Can I stop the route guidance function before I reach my destination?
Ÿ page 38, “Route guidance”
SafetyThe navigation system determines the position of the vehicle, the direction
and distance and the route to a selected destination without taking traffic
regulations into account. Navigation recommendations are given as
announcements by the system. Direction arrows are also shown on the
screen. The destination is entered when the vehicle is stationary. The
route guidance function is designed for cars and is thus unsuitable for
larger commercial vehicles.
sao.book Seite 14 Montag, 22. M‰ rz 2004 9:32 09

Navigation15
WARNING
x
Please observe the laws of road traffic legislation when
following the recommendations made by your navigation system.
x
Route guidance is subject to constant changes despite the
information about one-way streets, pedestrian zones etc. stored on
the navigation CD. Information on traffic lights, stop and right of
way signs, parking and stopping restrictions as well as lane
constrictions is not included in the navigation system. Traffic signs
and legislation always have priority over the recommendations
made by the system.
x
Adjust your speed to suit road traffic conditions and also
weather and visibility conditions. Do not drive faster in fog, for
example, if the navigation system tells you to do so.
The navigation CDInserting the navigation CD
– Press the button Ÿpage 2, fig. 1 to eject any CD in the
CD slot.
– Remove the CD and insert the navigation CD with the written side facing up.
– Push the CD into the slot until the radio navigation system pulls it in. The program stored on the navigation CD is loaded.
Do not remove the navigation CD before the loading process
is finished.
The navigation CD contains a digitalised road map. The extent to which
small villages, streets and house numbers are contained on the CD
depends on the CD version.
The content of the CD is constantly being updated. You will receive infor-
mation on new updates at your next Škoda Service. You will need a new
navigation CD for every country that you travel to.
Note
If the text CD ? is displayed in the small marking above the button,
the CD inserted in the CD drive can not be read.General notesYou can continue to listen to the radio or CD (via the CD changer) whilst
you are being guided to your destination.
When entering an address (town, street), only those letters or symbols
which make up a logical entry will be presented. A list of possible names
will be shown. Do not forget to enter the blank space in names made up
of more than one word, such as High Wycombe.
The route will be recalculated if you leave or disregard the route that was
originally calculated. This process takes only a few seconds.
The last announcement made can be repeated. The volume of a naviga-
tion recommendation can be changed whilst it is being made.
A variety of different information on the route can be called up during
active route guidance. The scroll function can be used to page through
lists shown on the screen, either line by line or page by page.
If the display Off Road appears on the screen, it means you are located
on a non-digitalised street, e.g. on a farm track. The GPS satellites will not
be able to reach your antenna when you are in a tunnel or underground
³
A8
CD
sao.book Seite 15 Montag, 22. M‰ rz 2004 9:32 09

Navigation17
Destination entryStarting destination entry
Two addresses can be entered for the route calculation;
the address of the destination and the address of the stop-
over destination.
– Press the key to enter the Navigation main menu
Ÿpage 2, fig. 1 .
– Press or in the Navigation main menu Ÿpage 16, fig. 13 to select between the destination entry
options.You will see a message that states that a destination has not yet been
defined if the destination is being entered for the first time. The last used
destination will be displayed if a destination has already been entered.
There are various methods of entering a destination or a stopover desti-
nation. The procedure for entering the stopover destination is the same as
for the destination.
– Enter the destination using town and street names
Ÿ page 18, “Entering a new address (town, street, house number)”.
or – Select a destination from a list of destina-
tions that have already been stored Ÿpage 19, “Last destinations”.
New address
To flagged dst.Destination
Destination
back with ESCEdit memory
Last dest.
From dst.mem. Special dests. Additional De...
Position dest.Dest. on map
Exhibition centre
Bra-0038
Fig. 14 Destination
back with ESCEdit memory
From dst.mem.
Last dest.
Special dests. Additional De...Position dest.Dest. on map
Stopover
StopoverTo flagged dst.
New address
Exhibition centre
Del. stopover
Bra-0079
Fig. 15 Stopover desti-
nation
NAVI
A13
Destination
Stopover
New AddressLast dest.
From dst. mem.
sao.book Seite 17 Montag, 22. M‰ rz 2004 9:32 09

Navigation
18
– Enter a restaurant, a garage, an airport, border crossing
etc. as a destination Ÿpage 21, “Special destinations close to the
address”.
– The position were you were located when you last
pressed button Ÿpage 2, fig. 1 is entered as the destination.
– Mark your destination on a map using a crosshair
Ÿ page 21, “Destination on the map”.
– Enter the longitude and latitude of a destination
Ÿ page 22, “Position destination”.
– Select a destination from the travel guide. A travel guide
is only available on certain navigation CDs. Further search functions
depend on the content of the travel guide.
– Store, delete or edit destinations in the destination memory
Ÿ page 23, “Destination memory”.
– Deletes the entered stopover destination.
Entering a new address (town, street, house number) – Press , or to enter the name
using the letter selection function.
Special dests.To flagged dst.
®
A9
Dest. on mapPosition dest.Additional De...Edit memoryDel. stopover
back with ESCContinue
Close to addr.
Dest. on map
Street Destination
Junction
New addressHouse number To w n
Centre Exhibition centre
Bra-0040
Fig. 16 Entering a new
address
Town
To w n
back with ESC
Bra-0041
Fig. 17 Entering a
town name
To w n
Street
House number
sao.book Seite 18 Montag, 22. M‰
rz 2004 9:32 09

Navigation19
– Enter the letters or numbers by turning and pressing the menu knob.
– You will see a list of names or numbers in the lower half of the screen. Press to enter the list.
– Select a name from the list by turning and pushing the menu knob. You can scroll through several pages of the list using the
scroll markers , , and and confirm your selection
by pressing .
– Press to select a special destination close to the destination address (town, street etc.) that you have already
entered.
and mark characters and deleted characters.
will display language-specific characters as necessary.
The term “Town” is used regardless of how many people live there. Both
a village of 100 inhabitants and a city with 1 million are named as towns.
A list of names to choose from will appear for town names which are used
more than once. The system will automatically switch to street entry after
town entry and then to house number entry. The centre of the town will be
offered as a destination if the town is so small that none of the streets have
been digitally mapped.
The keys and will not be active if a town name has
not been entered.
Note
Enter an intersection and house number as described.
Last destinations
The last destinations that have been used will be stored
automatically.
OKs
q
t
u
OK
Close to addr.
ƒ
„
„
z
Stree t
House number
Last dest. back with ESC
Last dest.
Bra-0080
Fig. 18 Last destina-
tions
Delete
Cancel
Edit memory back with ESC
Delete last dest.
Bra-0043
Fig. 19 Deleting last
destinations
sao.book Seite 19 Montag, 22. M‰rz 2004 9:32 09

Navigation21
Special destinations close to the address
Special destinations close to the destination can be
selected from a list.– Press Ÿpage 18, fig. 16 to select a special
destination close to the destination address (town, street etc.)
that you have already entered.Special destinations of the same category, e.g. restaurants, will be
displayed in a list. The nearest destination will be shown in the first posi-
tion.
Note
x
If you have not changed your destination address entry, the area close
to this last destination will be analysed and the special destinations there
will be listed.
x
The type and number of special destinations will be determined by the
content of the Navigation CD.
Destination on the map
A crosshair can be used to mark a destination on the map.–Press Ÿpage 17, fig. 14 .
– Use the right-hand function keys to move the crosshair to your required destination.
– Use or to alter the scale to suit your search strategy Ÿpage 33, “Changing the scale”.
Exhibition centre
Motorway exit
Motorway service st.
Car rental
Train station
Shopping centre
Ferry
Back with ESC
Close to addr.
Close to addr.
Bra-0045
Fig. 21 Special desti-
nations close to the
address
Close to addr.
Bra-0082
Fig. 22 Destination on
map
Dest. on map
ˆ
}
sao.book Seite 21 Montag, 22. M‰ rz 2004 9:32 09

Navigation27
Parameters for route calculationRoute options
– Press in the Navigation main menu Ÿpage 16,
fig. 13 .A short route might be quicker for your purpose in larger towns or cities
where there are a lot of traffic jams. Route options can be altered whilst
the route guidance function is active. The changed parameters will be
used as a basis for the calculation of the remaining journey.
Function keys in the route option menux
fast or short : Determines whether a fast or short route should be
calculated.
x
dynam. : Dynamic route guidance responds to traffic reports broadcast
by TMC stations. This function will automatically guide you round traffic
jams or blocked roads.
, or – Determines whether motorways, ferries or toll
roads should be used. These options will, however, be used for calculation
if there is no other logical route to the destination (e.g. an island is to be
used without using a ferry).
– Stores the selected settings for future route guidance usage.
Dynamic route guidance
An announcement that there are traffic jams on your route will be made if
a traffic jam is registered. You will also be warned directly before the traffic
jam itself.
Once the dynamic route guidance function has been activated you will be
informed that the route is being recalculated due to traffic problems if any
have been registered.
Traffic problems are indicated by a symbol on the map:
Route
with
with
without
without
back with ESC
Route options
short
Motorway Ferry
Toll fast
with without
by default dynam.
Bra-0091
Fig. 31 Route options
B
C
A
Bra-0092
Fig. 32 Symbols for
traffic problems
Route opt.
RouteMotorway
Ferry
To l l
by default
sao.book Seite 27 Montag, 22. M‰
rz 2004 9:32 09

Navigation
28w
Traffic jam Ÿpage 27, fig. 32
ƒ
Slow-moving traffic
‚
Road closed
The navigation system will calculate the quickest possible route when the
dynamic route guidance option is active. The system might well guide you
through a traffic jam if the diversion would be longer. Note
x
The dynamic route guidance option will only function if you are
receiving at least one TMC radio station.
x
The radio navigation system will automatically look for a new TMC
station if you leave the reception area of the one you are using. The station
you are listening to, however, does not have to be a TMC station.
x
The dynamic route guidance option will always use motorways, ferries
and toll roads.
x
The quality of the dynamic route guidance depends on the information
contained in the traffic announcements. The radio stations broadcasting
this information are responsible for the content.
Settings
The vehicle position can be entered manually and you can
then start a demonstration journey.
AA
AB
AC
DemoPos. on map Position Town
back with ESC
inactive
Syst. settings active
Set-up
Bra-0093
Fig. 33 Settings in the
Navigation main menu
Position Junction
25m ahead
Direction
Distance
back with ESC
Bra-0094
Fig. 34 Position
settings
sao.book Seite 28 Montag, 22. M‰
rz 2004 9:32 09

Navigation29
Entering your position
– Press in the Navigation main menu Ÿpage 16, fig. 13
to enter the vehicle position.
– Press . The entry window for the town appears. The entry for the street is made after you make your
entry and confirm it with . After confirming the name of the
street you will see a list of the streets which have an intersec-
tion with the named street.
– Select the intersection and confirm your choice by pressing the menu knob.
– Now enter your position either before or after this intersection in metres and also enter the direction of travel using the points
of the compass.
– Confirm your entry by pressing . The screen display will return to the Navigation main menu.
Entering your position on the map
– Press and then to see your set position on the map. The scale of the map can be altered using the two
top left-hand function keys.
– Press the button Ÿpage 2, fig. 1 twice to return to
the Navigation main menu.
Starting the demonstration
– Press and then select active. The navigation system is
activated. – The radio navigation system will now travel along the route
virtually from start to finish if the route guidance function is
started. You can listen to announcements and look at displays.
The navigation system will need some time for an exact definition of your
position if you have transported your vehicle using the train or a ferry. Your
position can be entered manually if the automatic definition is not
successful.
The manual position input can be used to calculate a route between any
two points regardless of where the vehicle is actually located.
Set-upPosition location
OK
OK
Set-up
Position map
ESC
A11
Demo
sao.book Seite 29 Montag, 22. M‰ rz 2004 9:32 09