SKODA OCTAVIA 2009 2.G / (1Z) Amundsen Navigation System Manual

General information
9
- deletes characters in the entry line
starting from the position of the char-
acter entry cursor from right to left. Selecting letters based on specific characters Some letters in the input masks are al
so marked with a small triangle “
a”. This indi-
cates that specific characters base
d on this letter can be selected.
Continue to press down on
the corresponding function key with your finger until a
pop-up window with these specific characte
rs can be displayed. Press to accept the
desired character into the entry line - the po
p-up window will close. If no entries are
entered, the pop-up window will cl
ose automatically after a few seconds.
Input mask for selecting the destination addressWhen entering the destination address,
it is only possible to enter the
characters in the sequence which corresponds to the destinations stored in the navigation system. Limiting the destination an
d selecting from the list
– You can open a list of the selectable destinations any time by pressing
the function key while making
entries in the entry line. Only
destinations selectable from the navigation memory which corre-spond to the requirements and the
character sequence in the entry
line will be displayed.
– The number of selectable destinatio
ns will be displayed in the entry
line if fewer than 99 dest
inations can be selected.
–If fewer than six destinations ar
e selectable, the entry window will
close automatically and a list of possible destinations will be displayed.
Delete
BAT-20H1086
Fig. 4 Input mask for selecting the destination address
List/OK
s36c.b.book Page 9 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP
10
Range selector key SETUPTo n e s e t t i n g sBy press ing the button and pres si ng on the functi on key in the
RADIO

mode, you can select the following para
meters using the menu control button :
•
- , ,
and - Volume when switching
on, volume of incoming traffic announce
ments, volume of navigation announce-
ments and speed dependent volume adjustment;•
- Treble setting;
•
- Midtone setting;
•
- Bass setting;
•
- Setting of the volume ratio between the left and right side;
•
- Setting of the volume ratio between the front and the rear;
•
* - Setting the equalizer (linear,
language, rock, cl
assical, dance);
•
* - setting of the surround tone.
GALA function Your radio increases automatically its volu
me with the increasing vehicle speed. A
higher setting value results in a stronger volume increase.
Note
You can set the tone parameters using th
e menu control button or the function
keys or .System settingsPress the button and select the function key .You can select between the following parameters:•
- Menu language for the displa
ys and the language messages;
•
- Keypad display for text entry;
•
* - if your vehicle
is equipped with clim
atronic, the setting
change is displayed when it is activated;•
- Setting the brightness of the screen;
•
- Factory settings;
•
- the information regarding the complete memory capacity of
the SD card and the size of the memory assi
gned to the navigation data is displayed
on the screen;•
- Removing the SD card.
Radio set-upsPress the button in the
RADIO
mode.
Switching the traffic announcements on or off – If you wish to switch the reception of traffic reports on or off, press the
function key .
Determining the station selection via the – By pressing on or , you can select the source
from which the stations are to be selected while in the
RADIO
mode
using the arrow keys. If the is selected, only stored stations from the memory list are called up. The symbol “
ƒ @ „” is
displayed on the screen.
Switching the RDS function on or off (RDS regional) – Press on the function key (regional station) and select a
set-up in the opening pop-up window.
SETUP
To n e
A10
Vo lume
Maximum switch on volume
Traffic announcements (TP)
Navigation volume
Speed dependent vol Adjustment
Tre b l eMidtoneBassBalanceFa d e rEQ SettingsSurround
A10
+
-
SETUP
System
Language
Keypad displayA/C display timeScreenFactory settingsSD card statusRemove SD card
SETUPTraffic information (TP)
Arrow keys
Station list
Memory listMemory listRDS regional
s36c.b.book Page 10 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP
11
– Press on the button , doing so always chooses the
frequency for the heard radio statio
n which offers the best reception
at the present time.
– When pressing on the button , the unit attempts to hold a radio
station emitting regionally long en
ough until the reception quality is
so bad, that there is a risk of a program loss.
Delete stored stations – Press the function key and confirm the following safety interroga-
tion in order to delete all radio stations stored in the memory list.
Tra f f i c s t a t i o n s e t - u p sPress the range selector key and then the range selector key
.
Switching the traffic announcements on or off A tick in the check box
7 indicates that the traffic radio function is already switched
on. Dynamic route Opens a pop-up window where it is considered if the TMC traffic reports, received during the route calculat
ion, are to be entered.
Screen set-upsPress the button in the
RADIO
mode and then the function keys
and .
Brightness – Press the function key and select the desired setting for
brightness (5°stages) in a pop-up window.
– A light sensor, which is located in the top right corner of the front
panel, is used for the automati
c correction of the brightness
depending on the light conditions in the vehicle.
Day/Night – Press on the func tion key and s el ec t a setting in the pop-up
window.
– Press the function key if switching the headlights on and off
should also change the map display from night to day design.
– Press on the function key
or to manually determine the
night and day design of the map display.
Confirmation tone – Press on the function key and select a setting in the
pop-up window.
– Press or to switch the tone for confirmation of a function key
operation on the screen on or off.
Media set-upsPress the button in the
MEDIA
mode.
Function keys in the menu°-°Media•
- a tick in the check box
7 means that the function of the
traffic information is switched on.•
- Check box for setting the play function mode Scan,
Mix and Repeat incl. sub-folder (“switched
on”) or without sub-folder (“switched
off”).•
- Setting the volume of the exte
rnal audio source (audio source
AUX is located on the unit).
Automatic
Fix
Delete memoryAllTRAFFIC
SETUP
Traffic information (TP)
˜ Dynamic routeSETUP
System
Screen
Brightness
Day/Night
Automatic
Day
Night
Confirmation tone
On
OffSETUP
Traffic information (TP)Scan/Mix/Repeat incl.

AUX Volume
s36c.b.book Page 11 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP
12
•
* - Setting the volume of the external audio source (the audio
source MDI is located under the armrest of the front seats or in a storage compart- ment on the front passenger side).•
* - enables a wireless transfer of MP3 data to the tele-
phone preinstallation. Only operates in
combination with the telephone preinstal-
lation GSM°l - enables the audio play func
tion by means of Bluetooth interface of
portable units (mobile phones) which support the protocol A2DP. Navigation settingsPress the button in the
Navigation
mode.
Function keys in the menu°-°Navigation•
- route options are determined according to the route being
calculated and along which roads the route should lead ,
, and - Route criteria, dynamic
route guidance, route without motorways and route without toll roads/ferries.•
- Setting the volume of th
e navigation announcements.
•
- changes between day and night display, as well as automatic, if the
map display changes automatically accordin
g to the setting of the light switch.
•
- displays a point of interest on the map.
•
- changes the map scale automati
cally depending on the speed and
the driven route (Motorway trip: small map scale - City center: large map scale).•
- during a route guidance, either the arrival or the driving time is
shown in the map display.•
- Enter home address.
•
- you can start a virtual (appare
nt) route guidance in the demo
mode. Virtual route guidance will be repe
ated when reaching the fictive travel
destination. Stop virtual route guidance
normally and deactivate the demo mode
to restart “real” route guidance. As in this case the unit must first reorient itself it can take some time, depending on the number of the currently receiving satellites, until the unit has again found the real location. Drive a short distance.•
- Entering a fictive (inven
ted) starting point in the
demo mode.
•
- Deleting the destination
memory or the list of the
last destinations.•
- Display of information via the data base on CD or SD
card, delete the data base of
the SD card or copy the data.
Route criteria Fa s t
: It calculates the fastest route to your de
stination, even if a detour is necessary.
Short
: Longer driving time in favour of a sh
orter route is acceptable. Please note
that the setting “Short route” during ro
ute guidance can sometimes lead to unex-
pected results. Economical
: The aim of the calculation is a ba
lance between mini
mal driving time
and driving distance. Dynamic route guidance with TMC use If the dynamic navigation is
switched off, traffic reports are nevertheless received in
the background and updated. The navigation displays traffic problems on the map and draws attention to them verbally, ho
wever does not consider them for calcu-
lating the route (the route can le
ad through the traffic problems).
MDI VolumeActivate Bluetooth audio
SETUP
Route options
Route criteria
Dynamic route
Avoid motorways
To l l r o a d / a v o i d
Announcement volumeDay/NightPOIs on mapAutozoomTime displayEnter home addressDemo modeDemo mode starting point
Delete destinations memoryData base navigation
Route criteria
Dynamic route
s36c.b.book Page 12 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO
13
Range selector key RADIORadio modeRetrieve radio stationCall up main menu RADIO and choose frequency range – Press the range selector key . The currently heard radio station
is displayed in the middle of the screen
⇒
page 7, fig. 2
.
– Press the range selector key
to change the frequency range.
Alternatively, press on the function key in the main menu RADIO
and select or in the pop-up window.
Changing radio station – By briefly pressing the function ke
ys or , you can change to the
previous or following radio station of the selected frequency band.
– If the symbol “
TP” is displayed on the screen, you can only change
over to the radio stations
with traffic announcements.
– If the symbol “
ƒ @ „” is displayed on the screen, you can only
change over to the stored radio stations.
Selecting a radio station from the station list – If you wish that all the presently receivable radio stations are
displayed, press on the function key and then on the func-tion key . The list “skips” directly to the display of the currently heard radio station.
– Select the desired radio station using the menu control button . Change radio station in the memory list – Press the function key and then the function key and
select the desired radio station using the function keys - .
Manual station finding – If you wish to set the radio statio
n manually using its frequency, press
the function key and then the function key .
– Set the radio station using the menu control button or using the
arrows and on the unit.
BAT-20H1064
Fig. 5 Menu radio: Function key band
BAT-20H1064
Fig. 6 FM station list
RADIO
AA
RADIO
Band
FM
AM
ƒ
„
Freq. Band
FM/List
A10
Extras
Memory1
24
Extras
ManualA10
ƒ
„
s36c.b.book Page 13 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO
14
– Briefly press the set button to te
rminate the manual frequency selec-
tion and to display once again the function keys.
Scan function – In order to start the
automatic play
in the current frequency range,
press the function key and then the function key . All radio stations with strong reception are automatically played for approxi-mately five seconds according to the sequence in the station list.
– Press on the function key to end the automatic play of the
currently heard radio station.
Storing a radio stationStoring a radio station – Press the function key and then the function key in
order to open the memory list.
– If you wish to store the displayed radio station in a memory space,
press one of the displayed station keys to and hold it pressed for so long until a signal
sounds. The currently heard radio
station is then stored on this station key.
Deleting a radio station from the memory list – Press the button in the
RADIO
mode and then the function key
.
– Select the radio station you wish to
delete and confirm by pressing the
menu control button .
– If you wish to delete all the stored
radio stations, press on the function
key .
Note
It is alternatively possible to store ra
dio stations by pres
sing the menu control
button .Calling up a radio stationCalling up a station via the station keys – Press the button and then the button and the function
key .
Extras
Scan
Scan
Extras
Memory
1 ...
24 ...
SETUP
Delete memory
A10
All
A10
BAT-20H1063
Fig. 7 Memory list
BAT-20H1075
Fig. 8 Setting the source for selecting the station
RADIO
Extras
Memory
s36c.b.book Page 14 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO
15
– You can select the station stored on one of the station keys to
in the main menu
RADIO
by briefly pressing the desired station key.
Calling up available stati
ons from the memory list
– Press the button and then the button and the func-
tion key .
– Select the desired radio station using the menu control button .RDS function– If you wish to switch the display of additional information to a radio
station on or off, press the button
, the function is displayed in the
top right corner of the screen by the letter “i”.
RDS (“
Radio
Data
System”) serves to transmit program identification and additional
services therefore also enabling automatic tracking of stations. In the event of sufficiently satisfactory reception, the suitable RDS radio stations will display the station name instead of the station frequency. If a radio station sends additional information via the RDS function while a station is being stored, it can occur that the name
of the radio station is later displayed
incorrectly in the memory list. In this case, the stored station name can be restored by selecting the desired radio station, wait until the correct station name is displayed as radio text then press the menu control button and a pop-up window is displayed on the screen.Traffic information function TPSwitching traffic information TP
(Traffic Program) on or off
– Press the function key in the
RADIO
mode.
– Briefly press on in the opening pop-up window to switch the
traffic information on or off.
The display “
TP” in combination with a station name (e. g. in the station or memory
list), indicates a traffic information station. Irrespective of which radio station is heard,
an additional receiver part in the unit
ensures that a traffic information station can always be received as long as the traffic information function is switched on. The functionality of the function for the traffic information “
TP” is displayed at the
top right in the screen. If no traffic information station can be re
ceived because, for
example, radio recep-
tion is interrupted in general, “
No TP
” will be displayed instead of “
TP”. Remember
that car parks, tunnels, high buildings or
mountains can interrupt the radio signal
up to the total loss of reception. Incoming traffic announcement If you wish to interrupt the transmission of the traffic announcement, press on the function key in the pop-up window
Traffic announcement
. The traffic infor-
mation function remains available and a following traffic announcement is replayed if a random source is switch
ed on. Pressing the function key will
switch off the traffic information function permanently.
1
24
RADIO
Freq. Band
FM/List
A10
º
A10
Station name stored
Extras
TP
Cancel
TP off
s36c.b.book Page 15 Thursday, April 9, 2009 2:50 PM

Range selector key TRAFFIC
16
Range selector key TRAFFICDisplaying TMC traffic reportsTMC traffic reports are used during
route guidance, depending on the
set-up for the automatic optimization of the route, to report possible traffic problems. – Press the range selector key to display the current traffic
reports in a list.
– Press on the display of a traffic report
to show it in a detailed display.
– You can browse through all the traffic information received in the
detailed display, in sequence by using the function keys.
Traffic problems are illustrated in the de
tailed display and in the map by a corre-
sponding symbol. The direction, in which the traffic problem is found in the map, is displayed in colour. A traffic problem which is located on the route (in direction of travel) is marked in red, a traffic problem in the opposite direction is marked in grey.
Note
•
The unit has a continuous background of
TMC traffic reports providing a TMC
station at the current location can be rece
ived. The station you are listening to does
not have to be a TMC station.•
TMC traffic reports can only be evaluate
d and stored by the unit if the nagi-
vation data (SD card or CD) is
available for the driven area.
•
The quality of the dynamic route guidan
ce depends on the transmitted traffic
announcements. The radio stations broadcasting this information are responsible for the content.•
TMC traffic reports are necessar
y for the dynamic navigation.
•
There may not be any advantage in avoiding the traffic jam if, as a result of the
TMC traffic reports, the diversion is also heavily congested.
TRAFFIC
s36c.b.book Page 16 Thursday, April 9, 2009 2:50 PM

Range selector key MEDIA
17
Range selector key MEDIAGeneral information for CD operationAudio-CDs (CD-A) and MP3-CDs can be
played in the internal drive.
CD not legible If you insert a CD which cannot be read by
the unit, a pop-up window is displayed
with a note. Press on the function key , the CD is driven to the initial position. If the CD is not taken out within 10 seconds, it is drawn in again for safety reasons.
WARNING
•
The CD player is a 1st class laser produc
t. There is a definite risk of injury
from invisible laser beams if it is opened.•
The CD player contains no parts that have to be serviced or repaired.
Please contact your speciali
st garage if a mechanical
defect occurs or the CD
player has to be repaired.
Caution
•
Inserting a second CD while a CD is being ejected can destroy the CD drive in
the unit. Please note that the CD ejecti
on lasts a few seconds after pressing the
Eject button
. During this time the lock in fr
ont of the CD case is open. It is
essential that you wait until the CD has been
fully ejected before you try to insert a
new CD.•
If the CD drive becomes me
chanically defective or
a CD has been inserted
incorrectly or not fully, “
Fa u l t : ° C D
” will be displayed on the screen. Please check the
CD and place it again correctly and fully into the drive. If “
Fa u l t : ° C D
” is indicated
again, please contact your Škoda Service Partner.•
If the inside temperature of the unit is
too high, no CDs will be accepted. The
unit switches into the last active operating mode.
Note
•
If the function key is inactive, no
new Audio CD has been inserted or an
inserted Audio CD is not readable.•
It is possible that CDs protected by copyright and self-made CD-R and CD-RW
are not returned at all or on
ly in certain circumstances.
•
Please observe the following information for the MP3 operation
⇒page 20.
•
Please comply with the national legal copyright requirements in your country.
Main menu MEDIAMain menu MEDIA - Overview
OK
š
CD
BAT-20H1065
Fig. 9 Main menu MEDIA: CD

mode
s36c.b.book Page 17 Thursday, April 9, 2009 2:50 PM

Range selector key MEDIA
18
Calling up the main menu MEDI
A and changing the media source
– Press the range selector key to switch to the main menu
MEDIA
. The last used audio source will continue to play.
Buttons on the unit for controlling the current audio sources The arrow keys on unit or will always affect the currently heard audio source, irrespective of the current menu used. - briefly press to go to the beginning of
the current track, press repeatedly to
return to the beginning of the previous track. - brief pressing changes over to the beginning of the next track.When in the menu of the currently played audio source it is also possible to change titles using the setting up button. - by briefly pressing, you can select the display for the additional information of the audio sources. Selectable audio sources in the menu AUDIO
CD - changes over to an inserted CD. CD 1-6
* - changes over to a connected external CD changer.
SD card
- changes over to an inserted memory card.
, or * - changes over to a connected external audio source.
Operating an externally connected audio
source is possible, wi
th certain restric-
tions, via the radio navigation unit and depends largely on the type of the connec- tion. Additional function keys in the AUDIO menu
- opens a pop-up window wher
e the random play function
Mix
, the auto-
matic play
Scan
or the replay of the track or the folder can be started.
- opens the list of the tracks for the current audio source in order to select
another track.Inserting or ejecting a CDInserting the CD – Push a CD with the written side facing
up as far as po ssible into the CD
case until it is automatically drawn in
. The play function will start auto-
matically.
Taking out the CD – Press the button to move the CD
in the internal CD drive into the
Eject position.
If a CD is not taken out in the initial position, it will be reinserted after approximately 10 seconds for safety reasons.Inserting or removing a memory cardInserting a memory card – Push the memory card into the me
mory card case with the trimmed
edge to the front top, until it is locked in position. The play function will start automatically.
Taking out a memory card – Press the button and then the function key .
BAT-20H1066
Fig. 10 Selectable sources in

the menu MEDIA
MEDIA
ƒ
„
ƒ„ºFFF

HAUX
MDI
BT audio
ExtrasSelect
šSETUP
System
s36c.b.book Page 18 Thursday, April 9, 2009 2:50 PM