lock SKODA OCTAVIA 2010 2.G / (1Z) Bolero Car Radio Manual
[x] Cancel search | Manufacturer: SKODA, Model Year: 2010, Model line: OCTAVIA, Model: SKODA OCTAVIA 2010 2.G / (1Z)Pages: 24, PDF Size: 1.14 MB
Page 5 of 24
General information
3
Note
Damage within the meaning of the warranty
must not be the result of improper
handling of the system or from unprofessi
onal repair attempts. It is also essential
that there is no external damage.Device operationThe unit should only be used, if the traffic situation permits it. The volume settings must be selected in
such a way that audible signals from the
outside, e.g. a Martins horn from utility
vehicles (police cars, ambulances and fire
brigade), can be heard at all times.
WARNING
Please concentrate fully at
all times on your driving! As the driver you are
fully responsible for road safety. Only use the functions of the radio in such a way that you are always in full contro
l of your vehicle in all traffic situa-
tions!
Caution
•
Inserting a second CD while a CD is being ejected can destroy the CD drive in
the unit. Please note that the CD ejecti
on lasts a few seconds after pressing the
Eject key
. During this time the lock in fron
t of the CD case is open. It is essen-
tial that you wait until the CD has been fully ejected before you try to insert a new CD.•
Press the buttons and the keys of the uni
t gently in order to avoid damaging
them. Gentle pressure on the appropriate key is sufficient to operate the unit. Please note that the control buttons have
predetermined breaking points, in order
to reduce the risk of injury.•
Do not use any pointed or sharp-edged objects to operate the touch-screen.
Slight finger pressure sufficient to oper
ate the equipment. A text in the display,
which cannot be called up by pressing the
button, is therefore not available at that
time.
Using the displayCarefully handle the display because dent
s and scratches can occur through pres-
sure of the finger or contact with sharp objects. The display can be cleaned wi
th a soft cloth and finger marks can be wiped away
with pure alcohol.
Note
Do not use solvent such as turpentine or
petrol as they will corrode the display
surface.Anti-theft protectionAnti-theft codingYour radio is equipped with
a convenience coding. If the radio is being operated for
the first time, the safety code is not only st
ored in the radio but also in the vehicle.
After disconnecting and reconnecting the battery, first of all switch on the ignition and then the radio. If you wish to install the radio in another
vehicle, the safety code must be entered.
In this case, please do not hesitate to co
ntact an authorised Škoda Service Partner
or a Škoda importer. As the unit only functions afte
r entering the safety code, this practically excludes its
use after a theft - a contribution to increased anti-theft safety.
Note
The code is stored in the instrument cluste
r. This ensures that it is automatically
decoded (convenience coding). Manual
input of the code is normally not
necessary.
/
s3p4.a.book Page 3 Friday, March 13, 2009 3:04 PM
Page 6 of 24
General information
4Enter codeIf a keypad appears after switching
on with the command to enter the
code, the unit can be unlocked by entering the correct four-digit code number. The number of the possible attempts is shown in the second display line. – Press directly a digit from to on the digit block displayed on the
display. The digit is accepted in the entry line.
– After a four-digit order has been entered, the group of digits will turn
grey (inactive) and no further digits can be accepted in the entry line.
– Press on the display to erase the digits in the entry line from right
to left and thereby correct your input, if necessary.
– If the correct code number is displayed in the entry line, press .Code number The code number can only be called up “onl
ine” via the Škoda system, as this guar-
antees even more effective anti-theft protection. Please contact your authorized Škoda Service Partner, if necessary. Incorrect code number If an incorrect code is confirmed after entry of the code, the procedure can be repeated
once again
. The number of attempts is shown in the second display line.
If the code number is entered incorrectl
y for the second time, the unit will be
blocked for approx. one hour. It is possible
to enter again the safety code after one
hour has expired, when the unit and the ignition have been switched on. If two invalid attempts are then made agai
n, the navigation system will be blocked
again for an hour. The cycle - two attempts, blocked for
an hour - will continue to apply.
General - operationThe screen of the unit is a so-called
touch screen (touch-screen). Fields
circled in colour on the touch-screen are presently “active” and are oper-ated by touching the screen. “Function keys” on the screen – Active fields, which call up a function or a Setup, are called “function
keys”.
– By using the function key you can
change back from each Setup to
the previous Setup.
Moving objects or regulators – Place your finger on the display
of a moving object on the touch-
screen, for example the “sliding regulator” in a “scrollbar”.
– Now move your finger over the touch-screen
without interruption
.
The object will follow your movement
s, but can only be moved within
the pre-defined range.
– Lift the finger from the touch-screen at the desired position. – To view the displayed Setup section, move the right sliding regulator
in the scrollbar completely to the bottom.
– Alternatively, you can move the slid
ing regulator on the touch-screen
to the bottom and top by touching the function keys and .
– A sliding regulator in a set-up bar
can alternatively be moved by
pressing or
“Scrollbar” The vertical bar on the right side of the
display with a sliding regulator between the
arrow keys and is called a “scroll bar”
. It indicates that further Setup entries
become visible if the sliding regulato
r is moved completely to the bottom.
0
9
OK
-
+
s3p4.a.book Page 4 Friday, March 13, 2009 3:04 PM
Page 8 of 24
Basic setting
6Basic settingSwitching the unit on and off– The system is switched on or of
f by pressing the control button .
The last active audio source before switching off is repeated. If the key is pulled out of the ignition lock while the unit is switched on, the unit will switch off automatically. You can then swit
ch the unit on again. If the ignition is
switched off, the unit (discharge protection
of the vehicle battery) switches off auto-
matically after approx. one hour. This
process can be repeated as often as
necessary.Audio settingsBy pressing the button you can select the following parameters:•
- Setting of height
, middle and depth;
•
- Volume ratio (left and right = balance), (front and rear = fader);
•
- , and * - Switch on
volume, traffic announcements and volume of park distance control signal;•
- Speed dependent volume adaptation;
•
- Switching on or off the tone signal when storing the radio
stations. Reducing the volume when activating the parking aid (PDC)* If your vehicle is
equipped with “parking aid”,
the volume is automatically
decreased to a pre-defined value, wh
en the “parking aid” is active.
GALA function Your radio increases automatically its volu
me with the increasing vehicle speed. A
higher setting value results in a stronger volume increase.
RADIO selector keySelecting a radio stationCall up main Setup RADIO and choose frequency range – Press the range selector key to call up the
RADIO
main Setup.
The currently heard radio station is indicated at the top of the display.
– To change the frequency range, press the button or the func-
tion key and on or in the opening pop-up window. The current frequency range is indicated at the top left of the display.
Changing radio station – By pressing the arrow keys on the display of the
RADIO
main Setup,
you can change to the previous or the following station.
Selecting a radio station from the station list – Press the function key to display all radio stations that can
currently be received. The list “skips” directly to the display of the currently heard radio station.
– Choose the desired station by pressing the respective selection. After
about 20 seconds without operation the image of the station list will close automatically.
Function keys in the Radio main Setup
to - Station keys for storing or calling up a stored radio station. - Button for selecting the desired frequency range.
- opens the list of the presently receivable radio stations. - opens the list of the stored radio stations.
A1
Treble-Mid-BassBalance faderVo lume
Startup volume
Traffic announcements
PDC
GALAConfirmation tone
RADIO
RADIO
Band
FM
AM
Station list
1...
...42
BandStation listMemory
s3p4.a.book Page 6 Friday, March 13, 2009 3:04 PM
Page 12 of 24
Basic setting
10
Taking out the CD – Press on the button , the CD is driven to the initial position.If a CD is not taken out in the initial position, it will be reinserted after approximately 10 seconds for safety reasons. WMA Data (Windows Media Audio) The copyright of audio data compressed by
Windows
Media
Audio, can also be
protected by the DRM procedure (
Digital
Rights
Management). Such WMA data is
not supported by the unit.Inserting or removing a memory cardInserting a memory card – Push the memory card into the me
mory card case with the trimmed
edge to the front right, until it is
locked in position. The play function
will start automatically.
Taking out a memory card – Press against the spring resistance
of the inserted memory card, the
memory card “skips” back into the Eject position.
Only MP3 data and unprotected WMA data ca
n be read from the SD card. All other
data is ignored. Memory card empty or data not readable If a memory card is inserted, on which no audio data has been stored, it will
not
be
switched over into the memory card mode after the loading procedure. In the Setup MEDIA
the function key remains inactive in the top display line and
the function cannot be seleced. Requirements of the memory card Memory cards measuring 32 mm x 24 mm x 2.1 mm or 1.4 mm can be inserted into the memory card case. Other memory cards of suitable size are
not
read by the unit.
Selecting a CD from the CD changer– Press the button , in order to open the
MEDIA
main Setup.
– If the unit is not already in the CD
m o de , p re s s o n th e f u n c t io n ke y
in the top display line.
– Press on the function key , in order to display the title list of
the currently played CD.
– Press on the function key as often as necessary until the CD selec-
tion Setup is displayed.
– Press on one of the buttons to , in order to start the
play function of the CD from
the corresponding position.
If the
currently played
CD is selected in the CD selection Setup, the title list is
opened. A CD compartment, in which no CD is inserted, is marked by “
Empty
” and the func-
tion key is shown as inactive. The CD which is currently playing, is indicated in the
MEDIA
main Setup at the top
left of the display.
- Random play function; the tracks
will be played in a random order.
– Scroll through the CD. The first
10 seconds of each title are played.
Note
CDs, which cannot be read by the CD changer, are also not selectable in the CD selection Setup of the radio (Display: “
Empty
”).
Select trackPress the range selector key to switch to the main Setup
MEDIA
.
/SD card
MEDIA
CD
SelectionCD 1:
CD 6:
MixScan
MEDIA
s3p4.a.book Page 10 Friday, March 13, 2009 3:04 PM
Page 19 of 24
Basic setting
17
3) and to - Shortcut keys; these can be allo-
cated to, in each case, one number.
- opens the number block for entering a call number.3) - opens a pop-up window for selecting
a call list. Only call lists of missed,
dialed or accepted calls from the mo
bile phone preparation program can be
displayed.
and
3) or - switches off the microphone
during a conversation
. Conversations held inside th
e vehicles cannot be heard by
the other party when the microphone is switched off.
- opens the phone book of the connected mobile phone for selecting a call
number.Enter call numberEnter a number and select – Press on the function key in the main Setup
PHONE
, in order to
open the number block for entering a call number.
– Press an inserted number key to accept the corresponding number in
the entry line.
– You can delete the characters in the entry line from right to left by
pressing the function key .
– Press function key when the desired call number is indicated in the
entry line. The connection to the entered call number is established.
You can select the character “
+” instead of the first two digits (for example “
00”)
when entering a country code. For this step, hold the function key with the little triangle “
” pressed until a pop-up window with the function keys and fades
in. Press to accept the desired character into
the entry line - the pop-up window will
close. If no entries are entered, the pop-
up window will close automatically after a
few seconds.
The special keys “Stars” and “Rhombus” have the same function as those on a phone keypad. These characters are prim
arily needed when transmitting sound
signals during a call.
4)
Phone bookOpening the phone book – Press on the function key in the
bottom right in the main Setup
PHONE
, in order to open the phone book.
Select phone number
from the phone book
– When in the Setup
Phone book
move the sliding regulator in the
scrollbar to the bottom to view further stations.
– Press on the function key to select a phone book entry via a
search mask.
– Press in the left column on the display of a phone book entry. The
connection to the
first
call number stored for this entry in the phone
book, will now be established.
5)
Displaying information relati
ng to a phone book entry
5)
– Press the function key on the right next to the phone book entry
you which to display. The call numbers stored under this entry are displayed.
– If you press on the entry of a call
number, the connection to this call
number will be established.
Voice mailbox
Memory 2
Memory 6
[:::]CallsExtras
Conference details
Microphone off
[:::]
00
+
4)Only valid for the universal Phone preinstallation GSM III.5)Only valid for the universal Phone preinstallation GSM III.
*
#
Search
s3p4.a.book Page 17 Friday, March 13, 2009 3:04 PM