lock SKODA OCTAVIA 2010 2.G / (1Z) Technical Change

Introduction1
IntroductionThis supplement replaces the Owner's manual OCTAVIA Edition 05.10 referred to in
the following as the Owner's manual.
The information given in this supplement takes preference over the information in the
Owner's manual.
Special equipment is marked with the symbol *.
We wish you a good journey
Škoda Auto a.s.Safelock
Note
When activating the Safelock function after you lock the vehicle, the message CHECK
SAFELOCK will appear in the display of the inst rument cluster. In vehicles equipped
with a MAXIDOT info display*, the message Check deadlock! Owner's manual!
(Observe SAFE locking! Car documentation!) appears. Windscreen wipersThe washing nozzles of the windscreen washer system are heated during engine
running and when the outdoor temperature is less than +10 °C * .
Seat heaters*Fig. 1 Dash panel: Regulator for front seat heating front/rear– Press the button
  fig. 1 - right to activate and regulate the heating for the
left/right rear seat.
If you regulate the rear seat heating at full power - level 3, this will automatically switch
back to level 2 after 10 minutes (2 wa rning lights in the switch light up).
“START - STOP”*The “START-STOP” system helps you to save fuel while at the same time reducing
harmful exhaust emissions and CO
2 emissions.
The function is automatically activated ea ch time the ignition is switched on.
Fig. 2 Dash panel: START-STOP System
button
s1ec.5.book Page 1 Friday, September 24, 2010 10:46 AM

Tyre repair kit*7
– Unscrew the valve cap.
– Use the screwdriver to remove the va lve core and place it down on a clean
surface.Seal and inflate tyresSealing tyres– Forcefully shake the tyre inflator bottle page 6, fig. 5 several times.
– Firmly screw inflation hose onto the tyre inflator bottle in a clockwise direction . The film on the cap is pierced automatically.
– Remove the plug from the inflation hose and plug the open end fully into the tyre valve.
– Hold the bottle with the floor facing up wards and fill the whole sealing agent in
the tyre inflator bottle into the tyres.
– Remove the empty tyre inflator bottle from the valve.
– Screw the valve core back into the tyre valve using the valve remover .Pumping up the tyres– Screw the tyre inflation hose page 6, fig. 5 of the air compressor firmly onto
the tyre valve.
– Check whether the air release valve is closed.
– Start the engine and run it in idle.
– Plug the cable connector into the 12 Vo lt socket in the vehicle, see Owner's
manual.
– Switch on the air compressor with the ON and OFF switch .
– Allow the air compressor to run until reac hing a pressure of 2.0 - 2.5 bars for a
maximum of 8 minutes !
– Switch off the air compressor. – If you cannot reach an air pressure of 2.0 – 2.5 bar, unscrew the tyre inflation hose
from the tyre valve.
– Drive the vehicle 10 metres forwards or backwards to allow the sealing agent to
distribute in the tyre.
– Screw the tyre inflation hose of the air compressor firmly back onto the tyre
valve and repeat the inflation procedure.
– If you cannot reach the required tyre inflation pressure here either, this means the tyre has sustained too much damage. You cannot seal with tyre with the break-
down kit .
– Switch off the air compressor.
– Remove the tyre inflation hose from the tyre valve.
If you reached a tyre inflation pressure of 2.0 – 2.5 bar, resume driving at a maximum
speed of 80 km/h (50 mph).
Check the tyre inflation pressure after driving 10 minutes page 8, “Check after
driving for 10 minutes”.
WARNING
•
During inflation, the tyre inflation hose and air compressor may get hot-
risk of injury!
•
Do not place hot tyre inflation hoses or hot air compressors on flammable
materials - risk of fire!
•
If you cannot inflate the tyre to at least 2.0 bar, this means the damage
sustained was too serious. The sealing agen t cannot be used to seal the tyre. Do
not drive the vehicle. Get professional assistance.Caution
Switch off the air compressor after running 8 minutes at the latest - danger of over-
heating! Allow the air compressor to cool a few moments before switching it on
again.
A1
A10
A3
A10
A3
A10
A1
A5
A7
A9
A8
A5
A5
A5
s1ec.5.book Page 7 Friday, September 24, 2010 10:46 AM