reset SKODA OCTAVIA 2012 2.G / (1Z) Owner's Manual

Instruments and warning lights
Instrument cluster
Introduction
This chapter contains information on the following subjects:
Overview
9
Engine revolutions counter
10
Speedometer
10
Coolant temperature gauge display
10
Fuel gauge display
10
Counter for distance driven
11
Setting the time
11
Display the charge level of the vehicle battery
11
Service Interval Display
11WARNING■ Concentrate fully at all times on your driving! As the driver you are fully re-
sponsible for the operation of your vehicle.■
Never operate the button in the instrument cluster while driving, only when
the vehicle is stationary!

OverviewFig. 2
Instrument cluster
First read and observe the introductory information and safety warn-
ings
on page 9.
Revolutions counter with warning lights » page 10
Display:
› With counter for distance driven
» page 11
› With service interval display
» page 11
› With digital clock
» page 11
› With multifunction display
» page 22
› With information display
» page 25
› with warning lights
» page 12
Speedometer 1)
with warning lights » page 10
Coolant temperature gauge » page 10
Bar with warning lights » page 12
Button for: › Set hours/minutes
› Service intervals display – Display of the number of days and kilometres
remaining until the next Service event
› Resetting Service Interval Display

1234561)
During the journey, the speed can be displayed in a different unit (mph or km/h) in addition to the
tachometer display.
9Instruments and warning lights

›Reset trip counter for the distance driven
› Charge level indicator
Fuel gauge » page 10
Fault display
If there is a fault in the instrument cluster, the following message will appear in the display:
Error: Instrument cluster. Workshop!
or INSTRUMENTCLUSTER_WORKSHOP
Ensure the fault is rectified as soon as possible by ŠKODA a specialist garage.

Engine revolutions counter
First read and observe the introductory information and safety warn-ings
on page 9.
The red scale of the rev counter
1
» Fig. 2 on page 9 indicates the range in which
the system begins to limit the engine speed. The system automatically restricts
the engine speed to a steady limit.
You should shift into the next higher gear before the red scale of the revolution counter is reached, or select mode D on the automatic gearbox.
Follow the recommended gear to prevent engine speeds that are too high or too low » page 21 .
For the sake of the environment
Shifting to a higher gear in good time helps to lower fuel consumption, minimises
operating noise levels, protects the environment and contributes to a longer lifeand reliability of the engine.
Speedometer
First read and observe the introductory information and safety warn-
ings
on page 9.
7Warning against excessive speeds
An audible warning signal will sound when the vehicle speed exceeds 120 km/h 1)
.
The audible warning signal is switched off when the vehicle speed falls below
this speed limit.
Coolant temperature gauge display
First read and observe the introductory information and safety warn-
ings
on page 9.
The coolant temperature gauge
4
» Fig. 2 on page 9 operates only when the ig-
nition is switched on.
The following guidelines regarding the temperature ranges must be observed to avoid any damage to the engine:
Cold range
If the pointer is still in the left area of the scale it means that the engine has not
yet reached its operating temperature. Avoid high speeds, full throttle and high
engine loads.
The operating range
The engine has reached its operating temperature as soon as the pointer moves
into the mid-range of the scale, for a normal style of driving. The pointer may also
move further to the right at high engine loads and high outside temperatures.
CAUTION
Additional headlights and other attached components in front of the fresh air in-
let impair the cooling efficiency of the coolant. There is then a risk of the engine
overheating at high outside temperatures and high engine loads » page 15.
Fuel gauge display
First read and observe the introductory information and safety warn-
ings
on page 9.
The fuel gauge
7
» Fig. 2 on page 9 only operates when the ignition is switched
on. 

1)
This function only applies to certain countries.
10Using the system

The fuel tank has a capacity of about 50 litres. The warning light lights up whenthe pointer reaches the reserve marking » page 18 .
CAUTION
Never drive until the fuel tank is completely empty! An irregular supply of fuel can
lead to irregular engine running. Unburnt fuel may get into the exhaust system
and damage the catalytic converter.
Note
The arrow  next to the icon  within the fuel gauge displays the installation lo-
cation of the fuel filler on the right side of the vehicle.
Counter for distance driven
First read and observe the introductory information and safety warn-
ings
on page 9.
Daily trip counter (trip)
The daily trip counter shows the distance driven since the time the counter was
last reset - in steps of 100 m.
The daily trip counter can be reset by briefly pressing the button
6
» Fig. 2 on
page 9.
Odometer
The odometer indicates the total distance which the vehicle has been driven.

Setting the time
First read and observe the introductory information and safety warn-ings
on page 9.
›
Press the button
6
» Fig. 2 on page 9 and keep it pressed down until the Time
appears.
›
Release the button
6
- the currently set time is displayed.
›
Press the button
6
again and set the hours.
›
Wait around 4 seconds - the system switches to the minutes setting.
›
Press the button
6
again and set the minutes.
The time can also be set in the Infotainment » operating instructions for Infotain-
ment , chapter Unit setup .

Display the charge level of the vehicle battery
First read and observe the introductory information and safety warn-
ings
on page 9.
›
Switch off the ignition.
›
Press the button
6
» Fig. 3 on page 22 and keep it pressed down until Battery
status /BATTERY appears.
›
Release the button
6
- the current charge level of the vehicle battery is dis-
played in %.

Service Interval Display
First read and observe the introductory information and safety warn-
ings
on page 9.
Service message
Before reaching the service interval, the icon 
appears in the display after the
ignition is switched on, together with the message:
Service in ... km or ... day(s).
or SERVICE IN... km OR ... DAYS
The kilometre indicator or the days indicator reduces in steps of 100 km or, where
applicable, days until the service due date is reached.
Once the service interval is reached, the icon 
appears in the display after the
ignition is switched on, together with the message:
Service now!
or SERVICE NOW
Displaying the distance and days until the next service interval › Switch on the ignition.
› Press the button
6

» Fig. 2 on page 9 and keep it pressed down until Service
appears.
› Release the button
6
.
The icon 
appears in the display, together with the message:
Service in ... km or ... day(s). 
11Instruments and warning lights

orSERVICE IN... km OR ... DAYS
Resetting Service Interval Display
After resetting the display with flexible service intervals, the displayed data is the
same as that for a vehicle with fixed service intervals. We therefore recommend
that the Service Interval Display is only reset by a ŠKODA Partner, who will reset
the display with a vehicle system tester.
The ŠKODA Partner:
› Resets the memory of the display after the appropriate inspection
› Adds an entry to the Service Schedule
› Affixes the sticker with the entry of the following service interval to the side of
the dashboard on the driver's side.
It can be reset with the button 6
» Fig. 2 on page 9.
› Switch off the ignition.
› Press the button
6
and keep it pressed down.
› Switch on the ignition.
› Release the button
6
and press again.
CAUTION
We recommend that you do not reset the Service Interval Display yourself as this
can result in the incorrect setting of the Service Interval Display, which can also
cause possible problems with the operation of your vehicle.
Note
■ Information is retained in the Service Interval Display even after the vehicle bat-
tery is disconnected.■
If the instrument cluster is exchanged after a repair, the correct values must be
entered in the counter for the Service Interval Display. This work is carried out by a ŠKODA specialist garage.
■
For more information on the service intervals » Service Plan .

Warning lights
Auto Check Control
Certain functions and conditions of individual vehicle systems are checked contin-
uously when the ignition is switched on.
Error messages and/or other information are displayed in the instrument cluster display. The messages are displayed at the same time as the symbols in the dis-
play and/or the warning lights » page 12.
Depending on the meaning, the icon  or  together with the message appears
in the bar with the warning lights
5
» Fig. 2 on page 9.
SymbolDescriptionWarningDanger
While the operational faults remain unrectified, the messages are always indica-
ted again. After they are displayed for the first time, the symbols 
or 
continue
to be indicated without any extra messages for the driver.
WARNINGIf you have to stop for technical reasons, then park the vehicle at a safe dis-
tance from the traffic, switch off the engine and activate the hazard warning
light system » page 49. The warning triangle must be set up at the prescri-
bed distance - observe the national legal provisions when doing so.

Overview
The warning lights show the following functions/faults and may be accompanied by audible signals.
When switching on the ignition, some indicator lights illuminate briefly as a func-
tion test. These indicator lights will disappear several seconds after the vehicle is
started. 
12Using the system

Driving data (Multifunction display)
Introduction
This chapter contains information on the following subjects:
Select data from the multifunction display
22
Memory
22
Multifunction display details
23
Warning against excessive speeds
24
The multifunction display only operates if the ignition is switched on. After the ig- nition is switched on, the function displayed is the one which you last selected
before switching off the ignition.
Individual menu items can be shown or hidden » Bedienungsanleitung Infotain-
ment, chapter Setting vehicle systems (CAR button) .
WARNINGConcentrate fully at all times on your driving! As the driver you are fully re-
sponsible for the operation of your vehicle.
Note
In certain countries the displays appear in the Imperial system of measures.
Select data from the multifunction displayFig. 3
Buttons (adjustment wheel) on the operating lever/multifunction
steering wheel
First read and observe the introductory information and safety warn-
ings
on page 22.
Selecting using the operating lever
›
Briefly press the rocker switch
A
» Fig. 3 up or down.
Selecting using the multifunction steering wheel
›
Turn the adjustment wheel
D
» Fig. 3 upwards or downwards.

Memory
First read and observe the introductory information and safety warn-
ings
on page 22.
The multifunction display is equipped with three automatic memories.
Select memory
›
Press the button
B
or adjustment wheel
D
» Fig. 3 on page 22.
Resetting
›
Select the desired memory.
›
Press longer on the button
B
or adjustment wheel
D
» Fig. 3 on page 22.
The following values of the selected memory are set to zero:
› Average fuel consumption
› Distance driven

22Using the system

Average speed
The average speed since the memory was last erased is shown in the display
in km/hour » page 22. To determine the average speed over a certain period of
time, set the memory to zero at the start of the measurement » page 22.
After erasing the memory, no average speed data will appear for approx. the first
300 m driven.
The display is updated regularly while you are driving. The average speed data is updated regularly while you are driving.
Distance travelled
The distance driven since the memory was last erased appears in the display.
If you want to measure the distance travelled from a particular moment in time on, at this moment, reset the memory by setting the button to zero » page 22.
The maximum distance indicated in both memories is 9 999 km. The indicator is
automatically set back to zero if this period is exceeded.
Driving time
The driving time which has elapsed since the memory was last erased, appears in
the display. If you want to measure the time travelled from a particular moment intime on, at this moment, reset the memory by setting the button tozero » page 22 .
The maximum distance indicated in both memories is 99 hours and 59 minutes. The indicator is set back to zero if this period is exceeded.
Convenience consumers
The consumption display for the convenience consumers in l/h.
Together with the consumption display, a list of three convenience consumers with the highest consumption is also displayed.
Warning against excessive speedsFig. 4
Buttons (adjustment wheel) on the operating lever/multifunction
steering wheel
First read and observe the introductory information and safety warn-ings
on page 22.
Adjust the speed limit while the vehicle is stationary
›
With the button
A
» Fig. 4 or, if applicable, the adjustment wheel
D
, select the
menu item Warning against excessive speeds .
›
Pressing the button
B
or the adjustment wheel
D
activates the setup mode
for the speed limit.
›
Set the desired speed limit, e.g. 50 km/h, with the button
A
or, if applicable,
the adjustment wheel
D
.
›
Confirm the speed limit by pressing button
B
, or adjustment wheel
D
or wait
around 5 seconds. Your settings are saved automatically.
This allows you to set the speed in 5 km/h intervals.
Adjusting the speed limit while the vehicle is moving
›
With the button
A
» Fig. 4 or, if applicable, the adjustment wheel
D
, select the
menu item Warning against excessive speeds .
›
Drive at the desired speed, e.g. 50 km/h.
›
Press the button
B
or the adjustment wheel
D
to accept the current speed as
the speed limit (the value flashes).
If you wish to change the set speed limit, it is changed in 5 km/h intervals (e.g. the
accepted speed of 47 km/h increases to 50 km/h or decreases to 45 km/h).
›
Press again the button
B
or the adjustment wheel
D
to confirm the speed lim-
it, or wait approx. 5 seconds and the setting is saved automatically (the value stops flashing). 
24Using the system

The cruise control system (CCS) maintains a constant speed, more than 30 km/h,
once it has been set, without you having to depress the accelerator pedal. This is
only possible within the range which is permitted by the power output and brak-
ing power of the engine.
The warning light  illuminates in the instrument cluster when the cruise control
system is activated.WARNING■ For safety reasons, the cruise control system must not be used in dense
traffic or on unfavourable road surfaces (such as icy roads, slippery roads,
loose gravel) – risk of accident!■
The saved speed may only be resumed if it is not too high for the current
traffic conditions.
■
Always switch off the cruise control system after use to prevent uninten-
tional use of the system.
CAUTION
■ The cruise control system is not able to maintain a constant speed when driving
in areas with steeper gradients. The weight of the vehicle increases the speed at which it travels. Therefore, shift to a lower gear in good time or slow the vehicle
down by applying the foot brake.■
It is not possible to switch on the cruise control system on vehicles fitted with a
manual gearbox if the first gear or reverse gear is engaged.
■
It is not possible on vehicles fitted with an automatic gearbox to switch on the
cruise control system if the selector lever is in the position P, N or R.
■
The Cruise Control System may automatically switch off when some brake as-
sist systems (e.g. ESC) intervene, when the speed exceeds maximum permissible
engine speed, or a similar event takes place.
■
The Cruise Control System also remains activated after shifting the gear!

Storing a speedFig. 111
Operating lever: Rocker switch
and switch of the cruise control
system
First read and observe the introductory information and safety warn- ings on page 119.
Storing a speed
›
Turn the switch
A
» Fig. 111 into the ON position.
›
After the desired speed has been reached, press the rocker button
B
into the
SET position.
After you have released the rocker button
B
out of the position SET, the speed
you have just stored is maintained at a constant speed without having to depress
the accelerator.

Changing a stored speed
First read and observe the introductory information and safety warn-
ings
on page 119.
Increasing the speed with the accelerator
›
Depress the accelerator to increase the speed.
›
Release the accelerator to reduce the speed back down to the preset speed.
Increasing the speed with the rocker button
B›
Press the rocker button
B
» Fig. 111 on page 120 into the RES position.
The speed will increase continuously, if the rocker button is pressed and held in
the RES position. Release the rocker button once the desired speed is reached.
The set speed is then stored in the memory. 
120Using the system