lock SKODA RAPID 2014 1.G Blues Car Radio Manual

As the unit only functions after entering the safety code, this practically excludes
its use after a theft - a contribution to increased anti-theft safety.
Note
The code is stored in the instrument cluster. This ensures that it is automatically
decoded (convenience coding). Manual input of the code is normally not necessa- ry.
Enter code
›
Switch on the radio with the ignition turned on. SAFE is displayed and then
1000 .
›
Use the selection buttons 1 - 4
8
to enter the safety code.
›
Confirm the safety code by pressing the selection buttons 6
8
.
If an incorrectly entered code is confirmed, the procedure can be repeated once
again.
If the code number is entered incorrectly for the second time, the unit will be
blocked for approx. one hour. It is possible to enter the safety code again after
one hour has expired if both the device and the ignition have stayed turned on
during that time.
The cycle - two attempts, blocked for an hour - will continue to apply.

Device specification and operation
Device specification
Fig. 1
Equipment overview

- Setting up button
› for switching the equipment on and off (press)
› for volume control (turn)
Settings knob › to activate the Scan function
› for settings in the individual operating modes
RADIO
button to activate the radio mode
MEDIA button to activate the play function of audio sources
Buttons  › manual station finding, select the track in CD mode (press briefly)
› fast station finding, fast forward/reverse in CD mode (press and hold)
Button TP
to activate the reception of traffic reports

1234563General information

CD player
Using the system
Information on how to use a CD
The internal drive can play CD-ROM, CD-R, CD-RW discs.
Insert the CD
With the labelled side facing up, only insert a CD into CD slot
10
until it is auto-
matically drawn in.
The play function will start automatically.
Taking out the CD
Press the 
button – the CD is ejected.
If the “ejected” CD is not taken out within 10 seconds, it will be drawn in again for
safety reasons.
Buttons on the unit for controlling the current audio source
The arrow buttons 
or  on the unit will always affect the audio source current-
ly being listened to, irrespective of the current menu used.

- brief pressing within 2 seconds of playback takes you to the beginning of the
previous track or chapter, or after 2 seconds to the beginning of the current title
or chapter.

- pressing this briefly changes over to the beginning of the next title or chap-
ter, repeated pressing changes over to the beginning of the subsequent title or
chapter.
Changing between the audio sources
Press the MEDIA
button to select the audio source:
CD (internal CD drive), EXT (CD
changer, if it is connected to the device) or AUX.
WARNINGThe CD-player is a laser product. On the manufacturing date, this unit was
classified as a class 1 laser product in accordance with the national/interna-
tional standards DIN EN 60825-1: 2008-05 and DHHS Rules 21 CFR,
Subchapter J classed as a class 1 laser product. The laser used in this class 1 laser product is so weak that there is no risk of danger when operated cor-
rectly. This product is designed such that the laser is restricted to the inside of
the unit. However, the installed laser could be classified in a higher class were the housing to be removed. For this reason, never remove the housing of the
unit.
CAUTION
■ Never insert CDs with the designation “ into the internal drive. Do not insert in
drives without a drawer ” or use Eco Discs.■
After pressing the button  there is a time delay of a few seconds before the
CD is ejected. During this time the lock in front of the CD-slot is open.
■
Be sure to wait until the CD has been fully ejected before you try to insert a new
CD. Otherwise you can damage the drive inside the unit.
■
A dirty, mechanically damaged, unreadable or incorrectly inserted CD can cause
playback problems. The CD may not be playable because of this or may cause it to
jump. Check the CD and insert it properly into the unit. Should problems persist ,
try using another CD and visit a specialist garage if necessary.
■
If the internal temperature of the device is too high, no CDs will be accepted.
The unit switches into the last active operating mode.
■
Never use liquids such as gasoline, paint thinner or record cleaner to clean the
surface of the CD - this may cause damage.
■
Never expose the CD to direct sunlight!
■
Only write on the CD using appropriate pens.
■
Do not stick anything to the CD.
Note
■ Poor or unsealed road surfaces and severe vibrations may cause the CD to jump.■In cold weather or after rain showers, moisture (condensate) may deposit in the
unit. This can effect the CD jump or impair the play function. In that case, wait un- til the moisture has dissipated.■
If a CD is dirty, never clean it in a circular motion, but instead work from the in-
side out. Use a soft, lint-free cloth. For heavy stains, we recommend that you
clean the CD with a commercially available CD cleaner and allow it to dry. 
6CD player