fuse SKODA SUPERB 2008 2.G / (B6/3T) User Guide

Fuses and light bulbs245
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Fuse assignment in the dash panel
Certain electrical components are only standard on certain vehicle model versions
or only suppliable as optional equipment for certain models.
No.Power consumerAmperes
1Diagnostic socket, engine cont rol unit, relay EKP, control
unit for EKP7,5
2Control unit for ABS, ESP, swit ch for tyre inflation pres-
sure-control system, brake sensor5
3Switch and control unit for airbag5
4WIV, parking light, dimming rear mirror, pressure sensor,
telephone preinstallation5
5Control unit for headlamp beam adjustment and head-
light swivel, control unit for parking aid5
6Instrument cluster, control unit for electromechanical
power steering, Haldex5
7Valve heating, air mass meter10
Fig. 216 Schematic repre-
sentation of the fuse carrier
in the dash panel
8Control unit for trailer detection5
9Relay for auxiliary heating5
10Adaptive left main headlight10
11Adaptive right main headlight10
12Central locking system of the front doors10
13Diagnostic socket, light switch, rain sensor, clock7,5
14Central locking system and bonnet lid15
15Central control unit - interior lights7,5
16The air conditioning system7,5
17Central locking system of the rear doors10
18Not assigned
19Not assigned
20ABS, ESP, Uphill-Start off-Assist5
21Not assigned
22Air blower for Climatronic40
23Front power window30
24Selector lever lock5
25Rear window heater
relay for auxiliary heating and ventilation25
30
26Power socket in the luggage compartment25
27Fuel pump relay,
Fuel pump relay, control unit for fuel pump, injection
valves15
20
28Not assigned
29Not assigned
30Not assigned
No.Power consumerAmperes
NKO B6 20.book Page 245 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs
246
Electrically adjustable seats are protected by automatic circuit breakers, which
switch on again automatically after a few seconds after the overload has been
eliminated.
Bulbs
Changing bulbs
The relevant lamp must always be switch ed off before a light bulb is replaced.
Defect light bulbs should only be replaced with light bulbs of the same type. The
designation is located on the li ght socket or the glass bulb.
Changing certain bulbs is not something wh ich you can do yourself, but requires to
be done by a specialist. Other parts of the vehicle must be removed in order to
change the light bulbs. This applies, in particular, to bulbs which can only be
reached from the engine compartment.
We therefore recommend that you have any bulbs changed by a Škoda Service
Partner or, in exceptional cases, by ca lling on other professional assistance.
Please note that the engine compartment is a hazardous area ⇒page 209,
“Working in the engine compartment”.
We recommend that you carry the set of light bulbs with you which was delivered
in your vehicle. Replacement light bulbs
17) are available at specialist garages.
The set of light bulbs can be stowed in the locable box in the spare wheel.
Fitted with a xenon headlight
Change of light bulbs on Xenon lights (low beam lights, parking lights and main
beam lights) should be undertaken by a specialist garage.
Overview of bulbs
31Not assigned
32Rear power window30
33Electric sliding/tilting roof25
34Alarm, spare horn5
35front and rear lighter25
36Headlight cleaning system20
37Front seat heating20
38Heated rear seats20
39Not assigned
40Fan air-conditioning system, relay for auxiliary heating
and ventilation40
41Not assigned
42Light switch5
43To w i n g d e v i c e15
44To w i n g d e v i c e20
45To w i n g d e v i c e15
46Heated windscreen washer nozzles, relay for auxiliary
heating and ventilation, switch for seat heating5
47Not assigned
48Not assigned
49Not assigned
No.Power consumerAmperes
17)Replacement light bulbs are, on the other hand, part of the basic equipping of the vehicle in
some countries.
NKO B6 20.book Page 246 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs247
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
•Bulbs H7 and H3 are pressurised and may burst when changing the bulb
- risk of injury!
•It is recommended to wear gloves and eye protection when changing a
light bulb.
•Gas discharge bulbs* (xenon bulbs) op erate with a high voltage, profes-
sional knowledge is required - danger to life!
Caution
Do not take hold of the glass bulb with naked fingers (even the smallest amount of
dirt reduces the working life of the light bu lb). Use a clean cloth, serviette or some-
thing similar.
Note
This Owner's Manual only describes the replacement of bulbs where it is assumed
that no major complications wi ll arise. Other light bulbs should be changed by your
specialist garage.
Front headlight
Positions of the light bulbs in the front headlight ⇒fig. 217 .
Front headlightHalogen headlightXenon headlight
Low beam H7D1S
Main beamH3D1S, H3
Parking lightsW5W
Tu r n s i g n a l sPY 24W
Fog lightsH8
Rear light unitBulb
Reversing lightW16W
Tu r n s i g n a l sPY21W
Light bulb for the brake lights and tail
lightsW16W
Parking lightsW5W
Fog lightsP21W
OthersBulb
Licence plate lightC5W
front interior lightingW5W
3. Brake lightLED
Rear interior lightingW5W
Storage compartment light - front pas-
senger sideC3W
Footwell lightW5W
Luggage compartment lightW5W
Door warning lightW5W
Lighting for vanity mirrorC5W
Entry lightW5W
Fig. 217 Front headlight:
Installing the light bulbs
NKO B6 20.book Page 247 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs
248
- parking lights and main beam lights
- low beam lights
- Turn signal light (at the front)
Parking lights and main beam lights
Removing the light bulb for the parking light
– Switch the ignition and all lights off.
– Open the bonnet.
– Remove the protective cap ⇒page 247, fig. 217 .
– Remove the socket ⇒fig. 218 .
– Take the faulty bulb out of the fixture and insert a new one.
Removing the light bulb for the main beam light
– Switch the ignition and all lights off.
– Open the bonnet.
– Remove the protective cap ⇒page 247, fig. 217 . – Press the sprung wire clamps
⇒fig. 218 together and hang them
to the side.
– Remove the socket ⇒fig. 218 .
– Take the faulty bulb out of the fixture and insert a new one
Installation takes place in the reverse order.
Note
We recommend that you have the headli ght setting checked by a Skoda Service
Partner after replacing the light bulb.
Low beam light
– Switch the ignition and all lights off.
– Open the bonnet.
– Remove the protective cap ⇒page 247, fig. 217 .
– Turn the connector with the light bulb up to the stop towards the left
and remove ⇒fig. 219 .
AA
AB
AC
B3T-0034H
Fig. 218 Removing the light
bulb for the parking and
main beam light
AA
AA
AA
AB
AC
Fig. 219 Removing the light
bulb for the low beam light
AB
NKO B6 20.book Page 248 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs249
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
– Replace the lamp, insert the connector with the new lamp and turn to
the right up to the stop.
– Insert the protective cover.
Note
We recommend that you have the headli ght setting checked by a Skoda Service
Partner after replacing the light bulb.
Fog lights
– Switch the ignition and all lights off. – Grasp the grille at the point marked with the arrow and take it out
⇒fig. 220 .
– Guide your hand into the opening in which the grille was located and
press the spring bolt ⇒fig. 221 .
– Take out the fog light.
– Turn the connector with the light bulb up to the stop towards the left and remove.
– Replace the lamp, insert the connector with the new lamp and turn to the right up to the stop.
– To re-insert the fog light, first of all place the fog light with the bolt on the side opposite the marking.
– Press into place the headlight onto the side facing the marking.
– FIrst of all put the grille in place on the side opposite the marking.
– Press into place the protective grille onto the side facing the
marking.
Rear light unitFig. 220 Front bumper:
Protective grille
Fig. 221 Remove front fog
lightFig. 222 Remove the outer
part of the rear light unit
NKO B6 20.book Page 249 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs
250
Remove and install the outer part of the rear light unit
– Switch the ignition and all lights off.
– Open the boot lid/luggage compartment door.
– Take out the plug ⇒page 249, fig. 222 and unscrew the rear light unit
using a torx wrench
18).
– Carefully remove the rear light unit. Do not pull the grommet with the cables out of the body.
– To re-insert the rear light unit, first of all guide it with the support ⇒fig. 224 towards the front onto a bolt on the bodywork.
– Carefully press the rear light unit into the bodywork.
– Screw the rear light unit tight and press in the plugs ⇒page 249,
fig. 222 .
Remove and install the inner part of the rear light unit
– Switch the ignition and all lights off.
– Open the boot lid/luggage compartment door. – Take off the cover of the rear light unit on the inner side of the bonnet
lid ⇒fig. 223 .
–Press the spring bolt ⇒fig. 223 and take the lamp holder out of the
housing of the rear light unit.
– To re-insert the lamp holder, guide it into the housing of the rear light
unit.
– Press onto the spring bolt until it locks in place.
– Guide the cover of the rear light uni t into the inner side of the bonnet
lid.
Caution
When removing and installing the rear light unit make sure not to damage the
paintwork of the vehicle and the rear light unit.
Changing light bulbs in the rear light unit
18)The torx wrench is located in a vehicle toolkit box on the spare wheel.
Fig. 223 Remove the inner
part of the rear light unit
AA
Fig. 224 Outer part of the
rear light unit: Lamps
NKO B6 20.book Page 250 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs251
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Change bulbs in the outer part of the rear light unit
– To change a bulb, turn its fixture to the left up to the top and take it out.
– Now change the bulb, insert again the fixture with the bulb into the
housing and turn it to the right up to the stop.
Change bulbs in the inner part of the rear light unit
– To change a bulb of the rear light ⇒fig. 225 , pull the defective bulb
out of the fixture and insert a new one.
– To change the bulb of the rear fog light ⇒fig. 225 , turn the defec-
tive bulb to the left up to the stop and take it out.
– Press a new bulb into the fixture and turn the bulb to the right as far as the stop.
Fitting position of the bulbs in the outer rear light unit ⇒page 250, fig. 224 .
1 - Turn signal light
2 - Parking lights / Brake light
3 - Parking lights
Fitting position of the bulbs in the inner rear light unit ⇒fig. 225 .
1 - Reversing lights 2 - Rear fog light
Licence plate light
– Unscrew the glass cover of the light
⇒fig. 226 .
– Take the faulty bulb out of the fixture and insert a new one.
– Replace the the glass cover of the light and press it down to the stop - ensure that the glass cover is correctly installed.
– Screw the glass cover tight.
Fig. 225 Inner part of the
rear light unit: Lamps
A1
A2
Fig. 226 Rear bumper:
Licence plate light
NKO B6 20.book Page 251 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs
252
Luggage compartment light
– Open the boot lid/luggage compartment door.
– Insert a narrow screwdriver into the slot ⇒fig. 227 and carefully take
out the light.
– Take the faulty bulb out of the fixture and insert a new one.
– Insert the light first of all on the side opposite the arrow and carefully
press it in stepwise until it locks in place.
Lighting for vanity mirror
Change the bulb in the lighting for the vanity mirror on the front
passenger side
– Insert a narrow screwdriver into the slot ⇒fig. 228 and carefully take
out the light.
– Take the faulty bulb out of the fixture and insert a new one.
– Insert the light first of all on the side opposite the arrow and carefully
press it in stepwise until it locks in place.
Change the bulb in the lighting for the vanity mirror on the driver
side
– Insert a narrow screwdriver into the sl o t o n t h e l e f t s i d e o f t h e l i g h t a n d
carefully pull out the light.
– Take the faulty bulb out of the fixture and insert a new one.
– Insert the light first of all on the right side and carefully press it in step- wise until it locks in place.
Interior lights at the rear
– Insert a narrow screwdriver into the slot ⇒fig. 229 and carefully take
out the cover.
Fig. 227 Remove the luggage
compartment light
Fig. 228 Lighting for vanity
mirror
Fig. 229 Roof liner light at
the rear
NKO B6 20.book Page 252 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs253
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
– Take the faulty bulb out of the fixture and insert a new one.
– Insert the light first of all on the side opposite the arrows ⇒page 252,
fig. 229 and press it in carefully until it locks in place.
Warning light in the doors and entry light
– Fold out the light in direction of arrow ⇒fig. 230 .
– Take the faulty bulb out of and insert a new one.
– First of all insert the light at the bottom and press in the upper part.
Fig. 230 Front door: Warning
light
NKO B6 20.book Page 253 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs
254
NKO B6 20.book Page 254 Wednesday, March 26, 2008 3:15 PM