headlight bulb SKODA SUPERB 2008 2.G / (B6/3T) Owner's Manual

Instruments and Indicator/Warning Lights
26
Warning lights
Overview
The warning lights indicate certain functions or faults.
Fig. 21 Instrument cluster with warning lights
Turn signal lights (to the left)⇒ page 27
Turn signal lights (to the right)⇒page 27
Fog lights⇒page 28
Main beam⇒page 28
Low beam⇒page 28
Rear fog light⇒page 28
Speed regulating system⇒page 28
Failure of the light bulbs⇒page 28
Adaptive headlights*⇒page 28
Diesel particle filter* (diesel engine)⇒page 28
Airbag system⇒page 29
NKO B6 20.book Page 26 Wednesday, March 26, 2008 3:15 PM

Instruments and Indicator/Warning Lights
28
Switching off the hazard warning light system is switched on will cause all of the
turn signal lights as well as both indicator lights to flash.
Further information about the turn signal system ⇒page 60.
Fog lights 
The warning light  comes on when the fog lights are operating ⇒page 57.
Main beam 
The indicator light  comes on when the main beam is selected or also when the
headlight flasher is operated.
Further information about the main beam ⇒page 60.
Low beam 
The warning light  comes on when low beam is selected ⇒page 53.
Rear fog light 
The warning light  comes on when the rear fog lights are operating ⇒ page 58.
Cruise control system* 
The warning light  lights up, when operating the speed regulating system.
Failure of the light bulbs 
The warning light  comes on if a light bulb is damaged:
•up to 2 seconds after the ignition is switched on;
•when switching on the defective light bulb.
The following text e.g will be displayed in the information display*: Check front right dipped beam!
The rear side lights and the licence plate lighting require several light bulbs. The
indicator light
 only lights up if all light bulbs of the licence plate lighting or the
parking light (in one rear light unit) are defe ctive. Check regularly the function of the
light bulbs.
Adaptive headlights*
If the warning light  flashes for 1 minute while driving or after switching on the
ignition and a warning signal sounds, a fault of the adaptive headlights is
confirmed.
Further information ⇒page 56.
Diesel particle filter*  (diesel engine)
If the warning light  comes on, this means that soot has accumulated in the
diesel particle filter because of the frequent short distances.
In order to clean the diesel particle filter, the vehicle should be driven at an even
speed of at least 60 km/h at engine speeds of 1 800 - 2 500 rpm for at least 15
minutes or until the warning light goes ou t with the 4th or 5th gear engaged (auto-
matic gearbox: position S) when the traffi c situation permits it. This increases the
exhaust temperature and the soot deposited in the diesel particle filter is burnt.
Always pay attention to the valid speed limits ⇒.
The warning light
 goes out after the successful cleaning of the diesel particle
filter.
If the filter is not properly cleaned, the warning light
 does not go out and the
warning light  begins to flash. In the information display* appears Diesel-
particle Owner's manual . Afterwards the engine contro l unit shifts the engine into
the emergency mode, which only has a re duced power output. After switching the
ignition off and on again the warning light
 comes on.
NKO B6 20.book Page 28 Wednesday, March 26, 2008 3:15 PM

Lights and Visibility57
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Mode city
In the mode “city”, the dispersion of the cone
of light in front of the vehicle is wider
and the width of illumination is shorter. It has as an aim to illuminate the adjacent
footpaths, crossings, pedestrian crossings etc. The mode is active at speeds of 15 -
50 km/h.
Mode motorway
In the mode “motorway” the dispersion of the cone of light is so widespread, that it
illuminates also the left (and right)
6) lane of the motorway, so that the driver can
react in time to an obstacle or any other danger. The mode is activated stepwise as
of a speed of 90 km/h. It gains its greatest effectiveness at speeds above 120 km/h.
Tourist light
When driving in countries with opposing traffic system, driving on the left/right, it is
possible to switch on the mode “tourist light” electronically. This mode makes it
possible to drive in the particular count ry without dazzling the oncoming vehicles.
When the mode “tourist light” is active, the above mentioned modes and the side
to side swivel of the headlight is deactivated.
The mode “tourist light” is activated in the information display* in the menu
⇒ page 19:
„SETUP (Settings)
„Automatic light (Automat. Lights)
Note
•The functions of the side to side swivel of the headlight* (activation at a speed
of 10 km/h), fog lights with the function “corner” ⇒page 57 and the function
dynamic headlight beam range* add to the System AHL*.
•The System AHL* is solely delivered with Bi-Xenon gas discharge bulbs for low
beam and main beam lights.
Fog lights 
Switching on the fog lights
– First of all turn the light switch into position
 or  ⇒ fig. 43 .
– Pull the light switch into position .
The rear fog light warning light  ⇒ page 26 lights up in the instrument cluster
when the fog light is switched off.
Fog lights with the function “Corner”*
The fog lights with the function “Corner” are designed for a better
illumination of all areas near the vehicle when corning, parking etc.
The fog lights with the function “Corner” are regulated according to the steering
angle or after switching on the turn signal light 7) in the following circumstances:
•the vehicle is stationary and the engine is running or it moves with a speed of
maximum 40 km/h;
•the daylight driving lights are not switched on;
6)It is valid for vehicles which are designed for driving on the left.
7)If both switch on versions are conflicting, for example if the steering wheel is turned to the
left and the right turn signal light is switched on, the turn signal light has the higher priority.
Fig. 43 Dash panel: Light
switch
A1
NKO B6 20.book Page 57 Wednesday, March 26, 2008 3:15 PM

Lights and Visibility59
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Headlamp range adjustment* 
Once the low beam is switched on you can then adapt the range of
the headlights to the load of the vehicle.
– Turn the control dial ⇒fig. 45 until you have adjusted the low beam
so that oncoming traffic is not dazzled.
Settings
The positions correspond approximat ely to the following vehicle loads:
Front seats occupied, luggage compartment empty.
All seats occupied, lugg age compartment empty.
All seats occupied, lugg age compartment laden.
Driver seat occupied, luggage compartment laden.
Caution
Set the headlight beam adjustment in such a way as to avoid dazzling oncoming
traffic.
Note
The Bi-Xenon bulbs* adapt automatically to the load and driving state of the vehicle
(e.g. speed, accelerating, braking) when the ignition is switched on and when driving. Vehicles which are not equipped
with Bi-Xenon bulbs* do not have a
manual headlight rang e adjustment control.
Switch for hazard warning lights 
–Press switch  ⇒ fig. 46 to switch the hazard warning light system on
or off.
All the turn signal lights on the vehicle flash at the same time when the hazard
warning light system is switched on. The indicator light for the turn signals and the
indicator light in the switch also flash at the same time. You can also switch on the
hazard warning light system if the ignition is switched off.
The hazard warning light system is switched on automatically if an airbag is
deployed in the event of an accident.
Please comply with any legal requirements when using the hazard warning light
system.
Note
Switch on the hazard warning light system if, for example:
•you encounter traffic congestion,
•your vehicle breaks down or an emergency situation occurs.
Fig. 45 Dash panel: Lights
and Visibility
A-
A1
A2
A3
Fig. 46 Dash panel: Switch
for hazard warning lights
NKO B6 20.book Page 59 Wednesday, March 26, 2008 3:15 PM

Lights and Visibility
60
The turn signal   and main beam lever 
The parking lights and headlight flasher are also switched on and off
using the turn signal and main beam lever.
The turn signal and main beam lever perform the following functions:
Right
 and left  turn signal light
– Push the lever upwards or downwards ⇒fig. 47 .
– If you only wish to flash three times* (the so-called convenience turn signal), push the lever briefly up to the upper or lower pressure point
and release it. This function can be activated/deactivated in the infor-
mation display* ⇒page 23.
– Turn signal for changing lanes - in or der to only flash briefly, move the
lever up or down to the pressure point and hold it in this position.
Main beam

– Switch on the low beam.
– Push the lever forwards.
– Pull the lever back into the initial position in order to switch the main beam off again. Headlight flasher

– Pull on the lever of the steering wheel (sprung position) - the main
beam and warning light in the instrument cluster come on.
Parking light

– Switch off the ignition.
– Push the lever up or down - the ri ght-hand or left-hand parking light
is switched on.
Information concerning the function of the lights.
•The turn signal system only operates when the ignition is switched on. The
corresponding indicator light  or  in the instrument cluster also flashes.
•The turn signal is automatically cancelled after negotiating a curve.
•The indicator light flashes at twice its normal rate if a bulb of the turn signal light
fails.
•The side light and rear light on the appr opriate side of the vehicle are switched
on when the parking light is selected. The parking light only operates if the ignition
is switched off.
Caution
Use main beam or the headlight flasher only if this does not risk dazzling other road
users.
Note
•If you have switched on the right or left turn signal light and you switch off the
ignition, the parking light is not automatically switched on.
•Use only in accordance with the legal requirements the described lighting and
signal systems.
Fig. 47 Turn signal and main
beam lever
NKO B6 20.book Page 60 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs
242
Fuse cover in engine compartment
The fuse box in the engine comp artment exists in two different
versions. You can determine which vers ion your vehicle is fitted with
after removing the fuse cover at the location of the fuses.
For particular model versions, the battery must be removed before
removing the fuse cover ⇒page 216.
Removing fuse cover
– Move the circlips ⇒fig. 213 as far as the stop, the symbol

appears behind the circlip and remove the cover.
Installing fuse cover
– Position the fuse cover on the fuse box and push the circlips as far as the stop - the symbol
 is visible behind the circlip.
Caution
•When unlocking and locking the fuse cover, it must be pressed on the sides to
the box, otherwise damage can occur to the locking mechanism.
•Carefully position the fuse cover in the engine compartment. If the cover was
not correctly positioned, water can get into the fuses and this results in a damage
to the vehicle!
Fuse assignment in engine compartment - version 1
Certain electrical components are only standard on certain vehicle model versions
or only suppliable as optional equipment for certain models.
Fig. 213 Fuse cover in engine
compartment
AA
AA
No.Power consumerAmperes
F1Front right main headlight, right rear light unit30
F2Valves for ABS20
F3Not assigned
F4Not assigned
F5Horn15
F6Power supply for terminal 15 (ignition on)40
F7Not assigned
F8Not assigned
F9Valves10
F10Not assigned
F11Lambda probe10
Fig. 214 Schematic repre-
sentation of fuse box in
engine compartment -
version 1
NKO B6 20.book Page 242 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs243
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
F12Lambda probe10
F13Control unit for automatic gearbox15
F14Not assigned
F15Water pump10
F16Not assigned
F17Instrument cluster, windshield wiper lever and turn sig-
nal light lever5
F18Audio amplifier (sound system)30
F19Radio15
F20Phone5
F21Not assigned
F22Not assigned
F23Engine control unit10
F24Control unit for CAN databus5
F25Not assigned
F26Not assigned
F27Va lve for fuel d osi ng15
F28Engine control unit15
F29Main relay5
F30Control unit for auxiliary heating20
F31Front window wiper30
F32Not assigned
F33Not assigned
F34Not assigned
F35Not assigned
No.Power consumerAmperes
F36Not assigned
F37Not assigned
F38Radiator fan, valves10
F39Not assigned
F40Not assigned
F41Not assigned
F42Not assigned
F43Ignition30
F44Not assigned
F45Not assigned
F46Not assigned
F47Front left main headlight, left rear light unit30
F48Pump for ABS40
F49Not assigned
F50Not assigned
F51Not assigned
F52Power supply relay - terminal a)40
F53Accessory equipment50
F54Not assigned
a)In order not to drain the battery unnecessarily when starting the engine, the electrical com-
ponents of this terminal are automatically switched off.
No.Power consumerAmperes
NKO B6 20.book Page 243 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs
244
Fuse assignment in engine compartment - version 2
Certain electrical components are only st andard on certain vehicle model versions
or only suppliable as optional equipment for certain models.
No.Power consumerAmperes
F1Not assigned
F2Control unit for automatic gearbox DQ20030
F3Measuring circuit5
F4Valves for ABS30/20
F5Control unit for automatic gearbox DQ25015
F6Instrument cluster, windshield wiper lever and turn sig-
nal light lever5
F7Power supply for terminal 15 (ignition on)40
F8Radio15
F9Phone5
F10Engine control unit, Main relay5/10
Fig. 215 Schematic repre-
sentation of fuse box in
engine compartment -
version 2
F11Control unit for auxiliary heating20
F12Control unit for CAN databus5
F13Engine control unit15/30
F14Ignition20
F15Lambda probe - Petrol
Glow plug system relay and fuel pump - Diesel10
5
F16Front right main headlight, right rear light unit30
F17Horn15
F18Audio amplifier (sound system)30
F19Front window wiper30
F20Valve for fuel dosing
water pump20
10
F21Lambda probe10/15
F22Not assigned
F23Main relay
Valves
High pressure pump5
10
15
F24Fa n10
F25Pump for ABS30/40
F26Left main headlight30
F27Control unit for glow plug system50
F28Not assigned
F29Accessory equipment50
F30Power supply relay - terminal X a)50
a)In order not to drain the battery unnecessarily when starting the engine, the electrical com-
ponents of this terminal are automatically switched off.
No.Power consumerAmperes
NKO B6 20.book Page 244 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs245
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Fuse assignment in the dash panel
Certain electrical components are only standard on certain vehicle model versions
or only suppliable as optional equipment for certain models.
No.Power consumerAmperes
1Diagnostic socket, engine cont rol unit, relay EKP, control
unit for EKP7,5
2Control unit for ABS, ESP, swit ch for tyre inflation pres-
sure-control system, brake sensor5
3Switch and control unit for airbag5
4WIV, parking light, dimming rear mirror, pressure sensor,
telephone preinstallation5
5Control unit for headlamp beam adjustment and head-
light swivel, control unit for parking aid5
6Instrument cluster, control unit for electromechanical
power steering, Haldex5
7Valve heating, air mass meter10
Fig. 216 Schematic repre-
sentation of the fuse carrier
in the dash panel
8Control unit for trailer detection5
9Relay for auxiliary heating5
10Adaptive left main headlight10
11Adaptive right main headlight10
12Central locking system of the front doors10
13Diagnostic socket, light switch, rain sensor, clock7,5
14Central locking system and bonnet lid15
15Central control unit - interior lights7,5
16The air conditioning system7,5
17Central locking system of the rear doors10
18Not assigned
19Not assigned
20ABS, ESP, Uphill-Start off-Assist5
21Not assigned
22Air blower for Climatronic40
23Front power window30
24Selector lever lock5
25Rear window heater
relay for auxiliary heating and ventilation25
30
26Power socket in the luggage compartment25
27Fuel pump relay,
Fuel pump relay, control unit for fuel pump, injection
valves15
20
28Not assigned
29Not assigned
30Not assigned
No.Power consumerAmperes
NKO B6 20.book Page 245 Wednesday, March 26, 2008 3:15 PM

Fuses and light bulbs
246
Electrically adjustable seats are protected by automatic circuit breakers, which
switch on again automatically after a few seconds after the overload has been
eliminated.
Bulbs
Changing bulbs
The relevant lamp must always be switch ed off before a light bulb is replaced.
Defect light bulbs should only be replaced with light bulbs of the same type. The
designation is located on the li ght socket or the glass bulb.
Changing certain bulbs is not something wh ich you can do yourself, but requires to
be done by a specialist. Other parts of the vehicle must be removed in order to
change the light bulbs. This applies, in particular, to bulbs which can only be
reached from the engine compartment.
We therefore recommend that you have any bulbs changed by a Škoda Service
Partner or, in exceptional cases, by ca lling on other professional assistance.
Please note that the engine compartment is a hazardous area ⇒page 209,
“Working in the engine compartment”.
We recommend that you carry the set of light bulbs with you which was delivered
in your vehicle. Replacement light bulbs
17) are available at specialist garages.
The set of light bulbs can be stowed in the locable box in the spare wheel.
Fitted with a xenon headlight
Change of light bulbs on Xenon lights (low beam lights, parking lights and main
beam lights) should be undertaken by a specialist garage.
Overview of bulbs
31Not assigned
32Rear power window30
33Electric sliding/tilting roof25
34Alarm, spare horn5
35front and rear lighter25
36Headlight cleaning system20
37Front seat heating20
38Heated rear seats20
39Not assigned
40Fan air-conditioning system, relay for auxiliary heating
and ventilation40
41Not assigned
42Light switch5
43To w i n g d e v i c e15
44To w i n g d e v i c e20
45To w i n g d e v i c e15
46Heated windscreen washer nozzles, relay for auxiliary
heating and ventilation, switch for seat heating5
47Not assigned
48Not assigned
49Not assigned
No.Power consumerAmperes
17)Replacement light bulbs are, on the other hand, part of the basic equipping of the vehicle in
some countries.
NKO B6 20.book Page 246 Wednesday, March 26, 2008 3:15 PM