lock SKODA SUPERB 2010 2.G / (B6/3T) Amundsen Navigation System Manual

General information5
Anti-theft protectionThe anti-theft coding of your radio naviga tion system prevents an operation of the
system after a voltage interruption, e.g. duri ng a vehicle repair or after theft. After
disconnecting the battery, disconnecting th e radio navigation system from the on-
board voltage of the vehicle and after a fuse failure, the code must be entered before
the vehicle can be used again.Enter code– If a keypad appears after switching on with the command to enter the code, the unit can be unlocked by entering the corr ect four-digit code number. The number
of the possible attempts is shown in the bottom screen line.
– Press a digit from to on the digit block displayed on the screen. The digit is accepted in the entry line.
– After a four-digit order has been entered, the group of digits will turn grey (inactive) and no further digits can be accepted in the entry line.
– Press on the screen in order to delete the digits in the entry line from right to left and thereby correct your input, if necessary.
– If the correct code number is displayed in the entry line, press .
Code number
The code number can only be called up “onl ine” via the Škoda system, as this guaran-
tees even more effective anti-theft protection. Please contact your authorized Škoda
Service Partner, if necessary.
Incorrect code number
If an incorrect code is confirmed after entr y of the code, the procedure can be repeated
twice . The number of possible attempts is shown in the bottom screen line.
If the code number is entered incorrectly for the third time, the unit will be blocked for
approx. one hour. It is possible to enter again the safety code after one hour has
expired, when the unit and the ig nition have been switched on.
If three invalid attempts are then made ag ain, the radio navigation system will be
blocked again for an hour.
The cycle - three attempts, blocked fo r an hour - will continue to apply.
Note
The code is normally stored in the instrument cluster. This ensures that it is automati-
cally decoded (convenience coding). Ma nual input of the code is normally not
necessary.
0
9
Delete
OK
s34g.6.book Page 5 Thursday, January 14, 2010 8:48 AM

General information
6
Operation when driving The demands of today's road traffic require fu ll concentration from all road users at all
times.
WARNING
•
Always concentrate fully on your driving. Inattention by the driver can lead
to accidents and injuries.
•
Do not allow yourself to be distracted by trying to use the unit, concentrate
instead on the traffic situation.
•
Use the unit only if road, weather and traffic conditions permit and you will
not be distracted.
•
The various volume settings must be selected in such a way that audible
signals from the outside, such as e.g. a Martins horn from police cars and fire
brigade, can be heard at all times.Note
Depending on the country, some functions of the radio navigation system can no
longer be selected on the screen at certai n speeds. This is not a malfunction, but corre-
sponds to the legal requirements of this particular country.Special functionsPar king aid*
If your vehicle is equi pped with “parking aid” and after it is activated, the distance to
the obstacle is shown on the screen.
Climatronic*
If your vehicle is equipped with climatronic, a feedback is received on the screen when
changing the settings.
Personalisation
Your vehicle can be equipped with up to fo ur keys. Individual settings of the unit are
always assigned to the key, which is currentl y inserted in the ignition lock. In practice, this means that each time you use another ve
hicle key, the setting of the unit which is
assigned to the key is carried out.
Switching the system on and off– The system is switched on or of f by pressing the control button .
The last active audio source before switching off is repeated.
If the key is pulled out of the ignition lock while the unit is switched on, the unit will
switch off automatically. You can then switch the unit on again. If the ignition is
switched off, the system switches off automa tically after approx. half an hour (vehicle
battery protection against discharging). Th is process can be repeated as often as
necessary.General - operationThe screen of the unit is a so-called touch screen (touch-screen). Fields circled in
colour on the touch-screen are presently “a ctive” and are operated by touching the
screen. Active fields, which call up a function or a menu, are called “ function buttons”
/ .
The following information is displayed in the main menu: the selected radio station (i ts frequency or designation);
selected waveband;
activation for the rece ption of traffic reports;
A1
Fig. 1 Menu radio
AD
AF
AAABAC
s34g.6.book Page 6 Thursday, January 14, 2010 8:48 AM

General information7
current menu.
“Pop-up window”
If you press the function key on the screen, a so-called “pop-up window” will open
in which all possible set-up options are displayed.
Briefly press the desired set-up option. The pop-up window will disappear and the
newly selected set-up option is displayed in the function key.
“Check box”
Some functions can only be switched on or off.
There is a so-called “Check box” in front of a function which can only be switched on
or off. A tick in the check box
=
indicates that the function is switched on, an empty
check box
>
, indicates that it is switched off.
Briefly press the corresponding function key for switching on or off.
Input mask for free text inputIn some of the menus you can enter a free text, for example, when entering a new
destination or while searching for the name of a point of interest.
– Press to accept a character sequence offered by the system or press in
order to delete the characters in the entry line.
– When in the entry window, press on a character shown on the keypad block to accept it into the entry line. – You can also delete or change the characte
r sequence in the entry line as well as
insert additional characters.
Further input possibilities: - changes from upper case to lower case and vice versa.
- opens the input mask for digits and special characters. The function key changes
to . Press , to change again to the letter input mask.
˜
- space key for entering spaces.
- switches to the Cyrillic script.
or - moves the character entry cursor (the cursor) in the entry line to the left or
right.
- opens a pop-up window with special characters. - deletes characters in the entry line starting from the position of the character
entry cursor from right to left.
Selecting letters based on specific characters
Some letters in the input masks are also marked with a small triangle “
a”. This indi-
cates that specific characters based on this letter can be selected.
Continue to press down on the correspondin g function key with your finger until a
pop-up window with these specific characte rs can be displayed. Press to accept the
desired character into the entry line - the po p-up window will close. If no entries are
entered, the pop-up window will clos e automatically after a few seconds.
Input mask for selecting the destination address
AE
AF
Fig. 2 Input mask for free text input
OK
Delete
:;A-Z
A-Z
~‚
b
ÄÜDelete
Fig. 3 Input mask for selecting the
destination address
s34g.6.book Page 7 Thursday, January 14, 2010 8:48 AM

Range selector key MEDIA17
Range selector key MEDIAGeneral information for CD operation Audio-CDs (CD-A) and MP3-CDs can be played in the internal drive.
CD not legible
If you insert a CD which cannot be read by the unit, a pop-up window is displayed with
a note. Press on the function key , the CD is driven to the initial position.
If the CD is not taken out within 10 seconds, it is drawn in again for safety reasons.
WARNING
The CD player is a 1st class laser product. There is a definite risk of injury from
invisible laser beams if it is opened.
Caution
•
Inserting a second CD while a CD is being ejected can destroy the CD drive in the
unit. Please note that the CD ejection lasts a few seconds after pressing the Eject
button . During this time the lock in front of the CD case is open. It is essential that
you wait until the CD has been fully ejected before you try to insert a new CD.
•
If the CD drive becomes mechanically defective or a CD has been inserted incor-
rectly or not fully, “ Error:°CD” will be displayed on the screen. Please check the CD and
place it again correctly and fully into the drive. If “ Error:°CD” is indicated again, please
contact your Škoda Service Partner.
•
If the inside temperature of the unit is t oo high, no CDs will be accepted. The unit
switches into the last active operating mode.Note
•
If the function key is inactive, no new Audio CD has been inserted or an
inserted Audio CD is not readable.
•
It is possible that CDs protected by copyright and self-made CD-R and CD-RW are
not returned at all or only in certain circumstances.
•
Please observe the following information for the MP3 operation ⇒page 20.
•
Please comply with the national legal copyright requirements in your country.
•
The CD player contains no parts that have to be serviced or repaired. If the CD
player is defective, contact a specialist garage.
Main menu MEDIAMain menu MEDIA - OverviewCalling up the main menu MEDI A and changing the media source– Press the range selector key to switch to the main menu MEDIA. The last
used audio source will continue to play.
OK
š
CD
Fig. 7 Main menu MEDIA: CD modeFig. 8 Selectable sources in the menu
MEDIA
MEDIA
s34g.6.book Page 17 Thursday, January 14, 2010 8:48 AM

Range selector key MEDIA
18
Buttons on the unit for controlling the current audio sources
The arrow buttons on unit or will always affect the currently heard audio source,
irrespective of the current menu used.
- briefly press to go to the beginning of the current track, press repeatedly to return
to the beginning of the previous track.
- brief pressing changes over to the beginning of the next track.
When in the menu of the currently played au dio source it is also possible to change
titles using the setting up button.
- by briefly pressing, you can select the display for the additional information of the
audio sources.
Selectable audio sources in the AUDIO menu
CD - changes over to an inserted CD.
CD 1-6* - changes over to a connected external CD changer.
SD card - changes over to an inserted memory card.
, or * - changes over to a connected external audio source.
Operating an externally connected audio sour ce is possible, with certain restrictions,
via the radio navigation unit and depends pr imarily on the type of the connected unit.
Additional function keys in the AUDIO menu - opens a pop-up window where the random play function Mix, the automatic
play Scan or the replay of the track or the folder can be started.
- opens the list of the tracks for the current audio source in order to select
another track.Inserting or ejecting a CDInserting the CD– Push a CD with the writ ten side facing up as far as possible into the CD case until it
is automatically drawn in. The play function will start automatically. Taking out the CD– Press the button to move the CD in the internal CD drive into the eject position.If a CD is not taken out in the initial position, it will be reinserted after approximately
10 seconds for safety reasons.
Inserting or removing a memory cardInserting a memory card– Push the memory card into the memory ca
rd case with the trimmed edge to the
front top, until it is locked in position . The play function will start automatically.Taking out a memory card– Press the button and then the function key .
– You can select the function key using the menu control button .
– Press against the spring resistance of the inserted memory card, the memory card “skips” back into the Eject position.
– After removing the SD card, confirm with on the screen.
Memory card empty or data not readable
If a memory card is inserted, on which no audio data has been stored, it will not be
switched over into the memory card mode after the loading procedure.
Requirements of the memory card•
Memory cards measuring 32 mm x 24 mm x 2.1 mm or 1.4 mm can be inserted into
the memory card case.
•
SD (Secure Digital Memory Cards) and MMC (Multimedia Cards) memory cards
with a capacity up to 4 GB.
•
SDHC (Secure Digital High-Capacity Memory Cards) memory cards with a capacity
up to 32 GB.
•
Due to the differing demands on quality of the card manufacturer, it is possible that
some of the data on the memory cards canno t be played or their play is restricted.
ƒ
„
ƒ„ºIII KAUX
MDI
Bluetooth audio
ExtrasSelect
š
SETUP
System
Remove SD card
A10
OK
s34g.6.book Page 18 Thursday, January 14, 2010 8:48 AM

Range selector key NAV (Navigation)29
– You can determine which types of destinations should be provided or not by using
the function keys , and
. These types of destinations will, however, be used for the
route calculation if there is no other logica l route to the destination (e.g an island is
to be used without using a ferry).
Determining the parameters for the route calculation•
Fa s t : calculates the fastest route to the dest ination, even if a detour is necessary.
•
Short: calculates the shortest route, even if a longer driving time is necessary.
Please note that the setting “Short route” during route guidance can sometimes lead
to unexpected results.
•
Economical : calculates a route with a driving time as minimal as possible and a
driving distance as short as possible.
Route guidance
Select the destination and start the route guidance. The unit will switch over to the map
display.
– You can change the scale of the map di splay by turning the menu control button
.
– The last navigation anno uncement is repeated if you press the menu control
button .
– If you press the range selector key , you can select between the menu
or .
– If you press the range selector key , you can change between the operating modes of the map by pressing the symbol
z.
If you press the function key in the operating mode , you can select
between the map displays.
•
,
•
and (different viewing angles of the map),
•
- during the active route guidan ce, the calculated route from the
current vehicle position to the entered destination is displayed,
•
.
The route to be driven is highlighted during the route guidance, the symbol
9
shows
the current vehicle position, the symbol

shows the distance to the destination and
the symbol

shows the estimated time of arrival or the driving time.
Stretches of the road ahead can also be blocked manually during a route guidance
⇒ page 30.
Stop route guidanceSelect the destination and start the route guidance. The unit will switch over to the map
display.
– The route guidance is interrupted and the function key changes to “ Start” by
pressing the range selector key and then the function key .
– If you press on the function key the route guidance will continue at the
current position.
˜ °Dynamic°route
˜°Avoid motorways
˜°Avoid toll roads/ferries
Fig. 15 Map display with function keysFig. 16 Map display during the route
guidance
A10
A10
NAV
Extras
Exit
NAV
Extras
NAV
2D north2D heading
3D heading
Overview mapMain menu
NAV
Exit
Start
s34g.6.book Page 29 Thursday, January 14, 2010 8:48 AM

Range selector key NAV (Navigation)
30
Inserting route listThe route list for the trip can only be displayed during a route guidance.Split-screen in the map display– An additional window opens if you pres s the button during route guidance.
– Select the function key in the a dditional window. The route list is
displayed. The list of the points (street names, street descriptions and stretches of
the road) still to be driven, is displayed in the Route list.
– In addition, the distance still to be driven on the driven road and the estimated time
to the following turning point are displayed.Manually excluding a stretch of the road– You can select the beginning of the stretch of the road to be excluded by using the
control button .
– Press on the function key , this changes to the function key .
– Select the end of the stretch of the road to be excluded and select the function key .
– The route is newly calculated.
– If you wish to cancel the exclusion of the stretch of the road, press the function key
.Dynamic route guidance with TMC use Switching the dynamic navigation on or off– Press the button and then select the function key while in the
main menu Navigation.
– In the menu Route options, activate the check box and select the
desired set-up by pressing your choice in the pop-up window.
Requirements for a dynamic route guidance
TMC (Traffic Message Channel) is a digital radio data service for continuous transmis-
sion of traffic information. The unit has a continuous background of
TMC traffic reports providing a TMC station
at the current locati on can be received.
The quality of the transmitted traffic report s depends on the broadcast editing carried
out by the radio station. The reception of the TMC traffic reports cannot be switched
on or off.
The station you are listening to does not have to be a TMC station.
TMC traffic reports can only be evaluated an d displayed by the unit if the navigation
data for the currently driven area is stored in the unit memory or can be called up via
an inserted navigation CD.
The current TMC traffic reports can be disp layed by pressing the range selector key
.
Note
•
There may not be any advantage in avoiding the traffic jam if, as a result of the TMC
traffic reports, the diversion is also heavily congested.
•
You can manually block the information for th e route in front of you if traffic prob-
lems ahead have not yet been included in the TMC traffic reports ⇒page 30.
º
Route list
A1
Exclude
Exclude to
Exclude toCancel
SETUP
Route options
˜°Dynamic°route
TMC
s34g.6.book Page 30 Thursday, January 14, 2010 8:48 AM

Range selector key PHONE31
Range selector key PHONEOverviewMain menu PHONE
Individual functions in the menu TELEPHONE may depend on the
equipment and the properties of the connected mobile phone.Connect your mobile phone with the mobile phone program according to the instruc-
tion manual applicable to your vehicle.
– Press the range selector key to call up the main menu PHONE.
After the connection process it will take a few minutes until the telephone book data
of the mobile phone connected to th e radio navigation unit is available.
Function keys in the main menu PHONE - Take calls, dial entered number. After pr essing the call list, the selected phone
numbers are displayed in the main menu PHONE.
- End conversation or reject call.* - establishes a connection to a an em ergency number after further confirma-
tion.
voice mailbox - select the voice mailbox number. select number - opens the number block for entering a call number.
non-accepted calls - shows a li st of the non-accepted calls.
selected number - shows a li st of the selected numbers.
accepted calls - shows a list of the accepted calls. Telephone book - opens the telephone book of the connected mobile phone for
selecting a call number.
WARNING
Concentrate fully at all times on your steering! As the driver you are fully
responsible for road safety. Only use the sy stem so that you are in full control of
your vehicle in every traffic situation - risk of accident!Enter call numberEnter a number and select– Press on the function key in the main menu PHONE, in order to open the
number block for enteri ng a call number.
– Press an inserted number key to accept the corresponding number in the entry
line.
– By pressing the button the characters in the entry line are deleted from right to left.
– Press function key when the desired ca ll number is indicated in the entry line.
The connection to the entered call number is established.
You can select the character “ +” instead of the first two digits (for example “ 00”) when
entering a country code.
The special keys “Stars” and “Rhombus” have the same function as those on a
mobile phone keypad. These characters are primarily needed when transmitting
sound signals during a call.
or - the cursor can be moved in the entered telephone number with the help of
the arrows.Telephone bookOpening the telephone book– Press on the function key in the main menu PHONE, in order to open the tele-
phone book.
PHONE
^SOS_[:::]|}{]
[:::]Delete
*
#
‚
b
]
s34g.6.book Page 31 Thursday, January 14, 2010 8:48 AM