wheel bolts SKODA YETI 2015 1.G / 5L Owner's Manual

Wheels
Tyres and wheel rims
Introduction
This chapter contains information on the following subjects:
Notes on using wheels
176
Tyre pressure
176
Tyre wear
177
Tyre wear indicator and wheel replacement
178
Tyre damage
178
Unidirectional tyres
178
Spare wheel
178
Spare wheel
179
Tyre label
179
Only use tyres or wheel rims that have been approved by ŠKODA for your mod-
el of vehicle.
WARNINGFor reasons of driving safety, do not replace tyres individually.
Note
■ We recommend that any work on the wheels or tyres be carried out by a spe-
cialist garage.■
We recommend that you use wheel rims, tyres, full wheel trims and snow
chains from ŠKODA Original Accessories.
Notes on using wheels
Read and observe
on page 176 first.
New tyres do not offer optimum grip during the first 500 km and appropriate
care should therefore be taken when driving.
Always fit the tyres with the deeper tread depth to the front wheels.
Tyre storage
Identify disassembled tyres so that the previous direction of rotation can be
maintained if the tyres are reassembled.
Always store wheels or tyres in a cool, dry place that is as dark as possible.
Tyres which are not fixed to a wheel trim should be stored upright.
Tyre age
Tyres age and lose their original characteristics, even if they are not being
used. The service life of the tyres is 6 years. Therefore, we recommend not us-
ing tyres that are older than 6 years.
Wheel bolts
Wheels and wheel bolts are matched to each other in terms of design. We rec-
ommend that you use wheel rims, wheel bolts from ŠKODA Original Accesso-
ries.WARNINGNever use tyres if you do not know anything about the condition and age.
Tyre pressure
Fig. 174
Label with a table of tyre sizes and tyre pressure value / inflate
tyres
Read and observe
on page 176 first.
The prescribed tyre inflation is on the sticker with pictograms
A
» Fig. 174 (for
some countries, the pictograms are replaced with a text).
Tyre pressure is always to match the load .
Inflation pressure for half load
Inflation pressure for environmentally-friendly operation
As a result of pressure level adaption to this value, the fuel consumption
and pollutant emissions may fall slightly.
Inflation pressure for full load 
BCD176General Maintenance

The fire extinguisher is attached by two straps in a holder underneath the driv-
er's seat.
Removing/attaching›
Loosen the two straps by pulling the buckles in the direction of the arrow
» Fig. 178 .
›
Remove the fire extinguisher.
›
Secure the fire extinguisher by placing it back into the holder and fastening
with straps.
Please read the instructions which are attached to the fire extinguisher.
Pay attention to the expiration date of the fire extinguisher. If the fire extin-
guisher is used after the expiration date, its proper function is not assured.
WARNINGThe fire extinguisher must always be secured safely so that they do not
come loose when making an emergency braking or in a vehicle collision
which could cause injuries to occupants.
Note
The fire extinguisher is part of the scope of delivery in certain countries only.
Vehicle tool kit
Fig. 179
Vehicle tool kit
The tool kit is housed in a box in the spare or emergency wheel compartment
or in this storage space.
Depending on the vehicle configuration, it may not contain all the compo-
nents listed in the on-board tool kit.
Screwdriver
Key for removing and installing the tail light
Adapter for anti-theft wheel bolts
Towing eye
Clamps for removing the wheel trims
Jack with sign
Wheel wrench
Extraction pliers for wheel bolt caps
Breakdown kitWARNINGThe factory-supplied lifting jack is only intended for your model of vehicle.
Under no circumstances attempt to lift heavier vehicles or other loads.
CAUTION
■ Screw the jack back into the starting position before storing in the box with
the tool kit.■
Ensure that the vehicle tool kit is safely secured in the boot.
■
Ensure that the box is always secured with the strap.
Note
The declaration of conformity is included with the jack or the log folder.
Changing a wheel
 Introduction
This chapter contains information on the following subjects:
Preparation
183
Removing/stowing the wheel
183
Full wheel trim
183
Wheel bolts
184
Anti-theft wheel bolts
184
Loosening/tightening wheel bolts
185
Raising the vehicle
185

123456789182Do-it-yourself

Remove the wheel / fix186Follow-up tasks186
For your own safety and the safety of the passengers, the following instruc-
tions must be observed before changing a wheel on the road.
Switch on the hazard warning lights system.
Place the warning triangle at the prescribed distance.
Park the vehicle as far away as possible from flowing traffic.
Choose a location with a flat, solid surface.
Have all the occupants get out. The passengers should not stand on the
road (instead they should remain behind a crash barrier, for instance) while
the wheel is being changed.
Tyres with increased puncture resistance
Some vehicles may be fitted with tyres at the factory that have increased
puncture resistance (“SEAL” tyres).
These vehicles are delivered without a puncture repair kit, spare wheel and appropriate hand tools.
If tyres with increased puncture resistance are replaced with tyres that have
no increased puncture resistance, then the vehicle should be equipped with a
puncture repair kit, spare wheel and appropriate hand tools.
Preparation
Before changing the wheel, the following work must be carried out.
›
Switch off the engine.
›
For vehicles with manual transmission select 1st gear.
›
On vehicles with automatic transmission place the selector lever in the P po-
sition.
›
Firmly apply the handbrake.
›
Uncouple any trailers.
Removing/stowing the wheelFig. 180
Take out wheel
The spare wheel is located in a well under the floor covering in the boot and is
fixed in place with a fastening screw.
Take out wheel
›
Open the boot lid.
›
Raise the floor covering in the boot » page 102.
›
Loosen the belt and take out the box with the tool kit.
›
Unscrew the fastening screw in direction of arrow » Fig. 180.
›
Remove the wheel.
Store wheel away
›
Place the wheel into the spare wheel well with the wheel rim pointing up-
wards.
›
Pull the fixing band through the opposite holes in the wheel rim.
›
Screw on the fastening screw in the opposite direction to the arrow
» Fig. 180 until the wheel is safely secured.
›
Replace the box with the tool kit into the emergency or spare wheel and se-
cure it with the tape.
›
Fold back the floor in the luggage compartment.
›
Shut the boot lid.
Full wheel trim
Before removing the wheel bolts, remove the wheel cover.
Extracting
›
Hook the clamp found in the vehicle tool kit » page 182 into the reinforced
edge of the wheel trim.
›
Push the wheel wrench through the clamp, support on the tyre and pull off
the wheel trim. 
183Emergency equipment and self-help

Fitting›Press the wheel trim onto the wheel rim at the designated valve opening.›
Then press the trim into the wheel rim until its entire circumference locks
correctly in place.
Notes from the factory or from the ŠKODA Original accessory delivered trim.
▶ When using an anti-theft wheel bolt, make sure that this has been fitted ac-
cording to the position marked on the back of the wheel cover position.
▶ On the back of the wheel cover, the position for the anti-theft wheel bolt is
marked by means of a symbol. If the wheel cover is set outside the position
marked for the anti-theft wheel bolt, there is a risk of damaging the wheel
cover.
If wheel trims are fitted, an adequate flow of air must be assured in order to
cool the brake system.
CAUTION
Use the pressure of your hand only, do not strike the full wheel trim. The cover
could be damaged.
Note
We recommend that you use wheel trims from ŠKODA Original Accessories.
Wheel bolts
Fig. 181
Remove the cap
Before removing the wheel bolts, remove the covering caps.
Extracting
›
Push the extraction pliers » page 182 sufficiently far onto the cap until the
inner catches of the pliers are positioned at the collar of the cap.
›
Remove the cap in the direction of the arrow » Fig. 181.
Fitting
›
Push the caps onto the wheel bolts up to the stop.
Anti-theft wheel boltsFig. 182
Principle sketch: Anti-theft
wheel bolt with adapter
The anti-theft wheel bolts protect the wheels from theft. These can only be
loosened or tightened with the use of adapter
B
» Fig. 182 .
›
Remove the full wheel trim or the caps of the wheel bolts.
›
Insert adapter
B
» Fig. 182 with the toothed side all the way into the inner
teeth in the head of the anti-theft wheel bolts
A
.
›
Push the wheel wrench onto the adapter
B
up to the stop.
›
Loosen or tighten the wheel bolt » page 185.
›
Remove the adapter.
›
Replace the wheel trim or the caps.
To be equipped for a possible wheel change, the adapter for the anti-theft
wheel bolts must always be kept in the vehicle. The adapter is stowed in the
tool kit.
The position of the anti-theft wheel bolt is marked on the back of the wheel
cover with every ŠKODA supplied original equipment hub cap or directly at the
factors.
When using an anti-theft wheel bolt, make sure that this has been fitted ac-
cording to the position marked on the back of the wheel cover position.
Note
■ Note the code number which is embossed both on the adapter and also on
the end of each anti-theft wheel bolt. This number can be used to purchase a
replacement adapter from ŠKODA Original Parts if necessary.■
The anti-theft wheel bolt set and adapter can be purchased from a ŠKODA
Partner.
184Do-it-yourself

Loosening/tightening wheel boltsFig. 183
Changing a wheel: Loosening the
wheel bolts
Before removing the wheel bolts, the caps for the wheel bolts must be pulled
off.
Release
›
Push the wheel wrench onto the wheel bolt until it locks into place.
Use the appropriate adapter for undoing the anti-theft wheel bolts » page 184.
›
Grasp the end of the wrench and turn the bolt about one turn in the direction
of the arrow » Fig. 183.
Tightening
›
Push the wheel wrench onto the wheel bolt until it locks into place.
Use the appropriate adapter for tightening the anti-theft wheel bolts
» page 184 .
›
Grasp the end of the wrench and turn the bolt against the direction of the
arrow » Fig. 183 , until it is tight.
After tightening the wheel bolts, the covering caps must be replaced.
WARNINGIf it proves difficult to undo the bolts, carefully apply pressure to the end of
the wrench with your foot. Keep hold of the vehicle when doing so, and
make sure you keep your footing.Raising the vehicleFig. 184
Jacking points for positioning
lifting jack
Fig. 185
Principle sketch: Attach lifting jack
Use the jack from the tool kit to raise the vehicle.
Position the car jack at the jacking point closest to the flat tyre .
The mounting points are located directly below the mark on the lower beam
» Fig. 184 .
›
Support the base plate of the jack with its full area resting on level ground
and ensure that the jack is located in a vertical position at the jacking point
» Fig. 185 -
 .
›
Position the lifting jack below the jacking point with the crank and move it up
until its claw encloses the web » Fig. 185 -
 .
›
Continue turning up the jack until the wheel is just about lifted off the
ground. 
185Emergency equipment and self-help

WARNING■If the wheel has to be changed on a slope, first of all block the opposite
wheel with a stone or similar object to prevent the vehicle from unexpect-
edly rolling away.■
Secure the base plate of the lifting jack with suitable means to prevent
possible moving. A soft and slippery ground under the base plate may move
the lifting jack, causing the vehicle to fall down. It is therefore always nec-
essary to place the lifting jack on a solid surface or use a wide and stable
base. If the surface is smooth, such as on cobbled stones, tiled floor, etc.,
use a non-slip base (e.g. a rubber foot mat).
■
Only attach the lifting jack to the attachment points provided for this pur-
pose.
■
Always raise the vehicle with the doors closed.
■
Never position any body parts, such as arms or legs under the vehicle,
while the vehicle is raised with a lifting jack.
■
When the vehicle is raised, never start the engine.
CAUTION
It is important to ensure that the jack is correctly attached to the web of the
lower fork leg - risk of damage to the vehicle.
Remove the wheel / fix
When changing a wheel, the following instructions must be followed.
›
Remove the full wheel trim or the caps of the wheel bolts.
›
First of all slacken the anti-theft wheel bolt and then the other wheel bolts.
›
Jack up the vehicle until the wheel that needs changing is clear of the
ground.
›
Unscrew the wheel bolts and place them on a clean surface (cloth, paper,
etc.).
›
Remove the wheel carefully.
›
Attach the wheel and slightly screw on the wheel bolts.
›
Lower the vehicle.
›
Tighten the wheel bolts opposite each other using the wheel wrench (alter-
nating crosswise). Tighten the anti-theft wheel bolt last.
›
Replace the wheel trim or the caps.
When fitting unidirectional tyres, ensure that the direction of rotation is cor-
rect » page 178 .
All bolts must be clean and must turn easily.
If it is established when changing a wheel that the wheel bolts are corroded and difficult to move, then these must be replaced.
Under no circumstances grease or oil the wheel bolts.WARNINGUndo the wheel bolts only a little (about one turn) as long as the vehicle
has not yet been jacked up. Otherwise the wheel could become loose and
fall off.
Follow-up tasks
After changing the wheel, the following work must be carried out.
›
Stow the replaced wheel in the wheel well and secure it with a special nut.
›
Stow the tool kit in the space provided and secure using the band.
›
Check the tyre pressure on the fitted wheel as soon as possible.
›
Have the tightening torque of the wheel bolts checked with a torque wrench
as soon as possible.
After changing the wheel, the tyre pressure should be adjusted. In vehicles
with tyre pressure monitoring, save tyre pressure values » page 141.
Replace the damaged wheel or consult a specialist garage about repair op-
tions.
The prescribed tightening torque of the wheel bolts is 120 Nm.
WARNING■
If the wheel bolts are tightened to a too low tightening torque, the rim
can come loose when the car is moving. A tightening torque which is too
high can damage the bolts and threads and this can result in permanent
deformation of the contact surfaces on the rim.■
Drive cautiously and only at a moderate speed until the tightening torque
has been checked.
Puncture repair kit
 Introduction
This chapter contains information on the following subjects:
Components of the puncture repair kits
187
General information
187

186Do-it-yourself

Index
A
abroad lead-free petrol
161
Abroad Headlights
69
ABS Operation
127
Warning light36
Acceptance and recycling of used vehicles152
Accessories149
Adaptive headlight see xenon headlight
66
AdBlue163, 164
refilling163
replenish164
adjusting auxiliary heating and ventilation
110
Adjusting Exterior mirrors
74
Head restraints79
Steering wheel9
Adjusting the seats8
adjustment Front seat
75
Adjustment Headlight beam
64
Seats76
AFS Display messages
36
Warning light36
AHL see xenon headlight
66
Air-conditioning system Air outlet vents
108
Airbag15
Deactivating19
Deactivating the front passenger airbag20
Deployment15
Front airbag16
Head airbag19
Knee airbag17
Modifications and damage to the airbag system 151
Side airbag
18
Warning light37
Airbag system15
Air conditioning104
Air distribution control107
Climatronic106
Manual air conditioning105
Air distribution control107
Air outlet vents108
Alarm Enable/disable
56
Switch off56
Trailer148
Triggering56
Alcantara cleaning
158
Alternator Warning light
33
Anodized parts Refer to vehicle maintenance
155
Anti-lock braking system (ABS)127
Anti-theft alarm system Enable/disable
56
Trailer148
Anti-theft wheel bolts184
Armrest Front
78
artificial leather158
Ashtray87
ASR warning light
35
Assistance systems OFF ROAD-mode
129
Assist systems127
ABS36
ASR35
ESC35
Auto Check Control31
Automatic driving lamp control66
Automatic gearbox Manual shifting of gears
123
Selector lever-emergency unlocking195
Selector lever lock123
Starting-off and driving124
Tiptronic123
Using the selector lever122
Automatic gearbox modes122
Automatic load deactivation175
automatic transmission selector lever lock defect
123
Automatic transmission122
Kickdown124
Selector lever lock123
AUX94
Auxiliary heating and ventilation Switching on and off directly
110
System settings110
Auxiliary heating (auxiliary heating and ventila- tion)
109
Auxiliary heating (aux. heating and ventilation) Radio remote control
111
Avoiding damage to your vehicle125
B
Ball head Check fitting
144
Ready position142, 143
Ball rod installing
143
removing144
Bar with sliding hook98
213Index

Headlight glasses155
Interior care157
Maintenance154
Materials158
Natural leather158
Plastic parts155
Polishing vehicle paint work154
Rubber seals155
Safety belt159
Seat covers159
Under-body protections157
washing152
Vehicle condition See Auto-Check Control
31
Vehicle data sticker204
Vehicle data sticker and nameplate Vehicle data sticker and nameplate
204
Vehicle dimensions207
Vehicle height207
Vehicle Identification Number (VIN)204
Vehicle length207
Vehicle tool kit182
Vehicle width207
vest Location of the reflective vest
181
VIN Vehicle Identification Number
204
Visibility70
Visors see front sun visors
71
W
Warning lights
32
MAXI DOT display31
warning messages Diesel particulate filter
37
Warning symbols MAXI DOT display
31
see Warning lights32
Warning triangle181
warning when speeding42
Washing Automatic car wash system
153
by hand152
High-pressure cleaner153
Washing vehicles152
Waste container88
Water in the fuel filter Warning light
31
warning messages31
Weather conditions149
Wheel bolts Anti-theft wheel bolts
184
Caps184
Loosening and tightening185
Wheel rims176
Wheels Age of wheels
176
Changing182
Driving style177
Full trim183
General information176
Load index179
Remove183
Snow chains180
Speed symbol179
Storage of wheels176
stow183
Tyre damage178
Tyre pressure176
Tyre size179
Tyre wear177
Tyre wear indicator178
unidirectional tyres178
Wheel balance177
Wheel replacement178
Winter tyres180
Wi-Fi Connection50
Password50
Password change51
Setting51
Wi-Fi Direct Connection
50
Password change51
Setting51
Window operation Malfunctions
61
Windscreen Heater
70
Windscreen washer fluid Checking
167
Replenishing167
Warning light38
Winter167
Windscreen washer system167
Windscreen washers72
Windscreen wiper Replacing the rear window wiper blade
196
Windscreen wipers automatic rear window wipers
72
Cleaning windscreen wipers195
Replacing the front windscreen wipers195
Service position of windscreen wiper arms195
Windscreen washer fluid167
Windscreen wipers and washers71
Winter operation180
De-icing window155
Snow chains180
Winter tyres180
Winter tyres See Wheels
180
Wiper blades157
Wipers Maintaining wiper blades
157
Wiping interval72
223Index