warning light SMART FORTWO COUPE 2015 Owner's Manual
[x] Cancel search | Manufacturer: SMART, Model Year: 2015, Model line: FORTWO COUPE, Model: SMART FORTWO COUPE 2015Pages: 222, PDF Size: 5.02 MB
Page 129 of 222
X
Push cap :onto the windshield washer
reservoir.
X Remount the service flap and close it
(Y page 123). Brake fluid
G
WARNING
During vehicle operation, the boiling
point of the brake fluid is continuously
reduced through the absorption of moisture from the atmosphere. Under extremely
strenuous operating conditions, this mois-
ture content can lead to the formation of
bubbles in the system, thus reducing the
system’s efficiency.
Therefore, the brake fluid must be replaced regularly. Refer to your vehicle’s Mainte-
nance Booklet for replacement interval.
The brake fluid level in the brake fluid
reservoir may be too low if the brake warn- ing lamp in the instrument cluster comes on(Y page 23) although the parking brake is
released.
! If you find that the brake fluid in the
brake fluid reservoir has fallen to the
minimum mark or below, have the brake
system checked for brake pad thickness
and leaks immediately. Contact an
authorized electric drive smart center
immediately. Do not add brake fluid as
this will not solve the problem.
X Remove the service flap and insert it on
the front of the vehicle (Y page 123).
The brake fluid reservoir is located in the
front compartment on the passenger side. Checking brake fluid level
X
Perform a visual check of the brake fluid
reservoir :.
The brake fluid level is correct when it
is between the minimum mark and the
maximum mark. R If the brake fluid level has fallen
slightly below the minimum mark,
drive to an authorized electric drive
smart center.
R If the brake fluid level has fallen sig-
nificantly below the minimum mark,
call Roadside Assistance or an author- ized electric drive smart center.
X Remount the service flap and close it
(Y page 123). Tires and wheels
Safety notes
Contact an authorized electric drive smart
center for information on tested and rec-
ommended rims and tires for summer and
winter operation. They can also offer
advice concerning tire service and pur-
chase. G
WARNING
Replace rims or tires with the same desig- nation, manufacturer and type as shown on
the original part. For further information
contact an authorized electric drive smart
center. If incorrectly sized rims and tires are mounted, the wheel brakes or suspen- Tires and wheels
127>> Operation.
Z
Page 140 of 222
Treadwear indicator
:appears as a solid
band across the tread.
Storing tires !
Keep unmounted tires in a cool, dry
place with as little exposure to light as
possible. Protect tires from contact with oil, grease and fuels.
Cleaning tires !
Never use a round nozzle to power wash
tires. The intense jet of water can result in damage to the tire.
Always replace a damaged tire. Uniform Tire Quality Grading Stand-
ards
The Uniform Tire Quality Grading is a U.S.
Government requirement designed to give
drivers consistent and reliable informa-
tion regarding tire performance. Tire
manufacturers are required to grade tires
based on three performance factors: tread- wear
:, traction ;, and temperature
resistance =. Although not a Government
of Canada requirement, all tires made for
sale in North America have these grades
branded on the sidewall.
i For illustration purposes only. Actual
data on tires are specific to each vehicle and may vary from data shown in above
illustration.
Quality grades can be found, where appli-
cable, on the tire sidewall between tread
shoulder and maximum section width. For
example: Treadwear Traction Temperature
200 AA A
All passenger car tires must conform to
federal safety requirements in addition to
these grades.
Treadwear The treadwear grade is a comparative rat-
ing based on the wear rate of the tire when
tested under controlled conditions on a
specified U.S. government test course. For example, a tire graded 150 would wear one
and one-half (1 1
/ 2 ) times as well on the
government course as a tire graded 100.
The relative performance of tires depends
upon the actual conditions of their use,
however, and may depart significantly from
the norm due to variations in driving hab-
its, service practices and differences in
road characteristics and climate.
Traction G
WARNING
The traction grade assigned to this tire is based on straight-ahead braking traction
tests, and does not include acceleration,
cornering, hydroplaning, or peak traction
characteristics. 138
Tires and wheels>> Operation.
Page 142 of 222
A
Manufacturer
B Tire ply material (Y page 143)
C Tire size designation, load and speed
rating (Y page 140)
D Load identification (Y page 142)
E Tire name
i For illustration purposes only. Actual
data on tires are specific to each vehicle and may vary from data shown in above
illustration.
For more information, see “Rims and
tires” (Y page 216).
Tire size designation, load and speed
rating :
Tire width
; Aspect ratio in %
= Radial tire code
? Rim diameter
A Tire load rating
B Tire speed rating
i For information purposes only. Actual
data on tires are specific to each vehicle and may vary from data shown in above
illustration.
General:
Depending on the design standards used,
the tire size molded into the sidewall may
have no letter or a letter preceding the tire
size designation.
No letter preceding the size designation
(as illustrated above): Passenger car tire
based on European design standards. Letter “P” preceding the size designation:
Passenger car tire based on U.S. design
standards.
Letter “LT” preceding the size designa-
tion: Light Truck tire based on U.S. design
standards.
Letter “T” preceding the size designation: Temporary spare tires which are high pres-
sure compact spares designed for tempo-
rary emergency use only.
Tire width
Tire width :indicates the nominal tire
width in mm.
Aspect ratio
Aspect ratio ;is the dimensional rela-
tionship between tire section height and
section width and is expressed as a per-
centage. The aspect ratio is arrived at by
dividing section height by section width.
Tire code
Tire code =indicates the tire construc-
tion type. The “R” stands for radial tire
type. Letter “D” means diagonal or bias ply
construction; letter “B” means belted-bias
ply construction.
At the tire manufacturer’s option, any tire
with a speed capability above 149 mph
(240 km/h) can include a “ZR” in the size
designation (for example: 245/40 ZR 18).
For additional information, see “Tire
speed rating” (Y page 141).
Rim diameter
Rim diameter ?is the diameter of the
bead seat, not the diameter of the rim edge. Rim diameter is indicated in inches (in).
Tire load rating G
WARNING
The tire load rating must always be at least
half of the GAWR of your vehicle. Otherwise, tire failure may result and cause an acci-
dent and/or serious personal injury to you
or others. 140
Tires and wheels>> Operation.
Page 156 of 222
soft top fabric*. Environmental influen-
ces are not covered by the smart Limited
Warranty.
Frequent washing reduces and/or elimi-
nates the aggressiveness and potency of the
above adverse influences.
More frequent washings are necessary to
deal with unfavorable conditions:
R near the ocean
R in industrial areas (smoke, exhaust
emissions)
R during winter operation
You should check your vehicle from time to time for stone chipping or other damage.
Any damage should be repaired as soon as
possible to prevent corrosion.
In doing so, do not neglect the underbody of
the vehicle. A prerequisite for a thorough
check is a washing of the underbody fol-
lowed by a thorough inspection. Damaged
areas need to be re-undercoated.
Your vehicle has been treated at the factory with a wax-base rustproofing in the body
cavities which will last for the lifetime of
the vehicle. Post-production treatment is
neither necessary nor recommended by
smart because of the possibility of incom-
patibility between materials used in the
production process and others applied
later.
We have selected vehicle-care products
and compiled recommendations which are
specially matched to our vehicles and
which always reflect the latest technology. You can obtain smart approved vehicle-
care products at an authorized electric
drive smart center.
Scratches, corrosive deposits, corrosion
or damage due to negligent or incorrect
care cannot always be removed or repaired with the vehicle-care products recommen-
ded here. In such cases it is best to seek aid
at an authorized electric drive smart cen- ter. The following topics deal with the cleaning
and care of your vehicle and give important
“how-to” information as well as references to smart approved vehicle-care products. Vehicle care
Contact an authorized electric drive smart
center for recommended and approved care
products.
i Advice on caring for the soft top sys-
tem, see (Y page 157). G
WARNING
After washing the vehicle, the brakes may
still be wet and thus their functionality
impaired. Therefore, when you start off,
brake lightly several times without endan- gering traffic. 154
Vehicle care>> Operation.
* optional
Page 158 of 222
Exterior Special considera-
tions Lightly soiled
Hand-/Automatic
car washes Heavily soiled
Hand-/Automatic
car washes
Wheels and wheel
covers Two-layer metallic
paint (high-gloss) Car shampoo con-
centrate, rim care Car shampoo con-
centrate, rim care
Retractable soft top PAC fabric Car shampoo con-
centrate, soft top
cleaner, impregna-
tion spray Car shampoo con-
centrate, soft top
cleaner, impregna-
tion spray
Removing insects
Remove insect remains before you start to
wash the vehicle.
X Spray insect remover on.
X Allow insect remover to work in briefly.
X Rub in gently with a soft cloth or sponge.
X Rinse with plenty of water.
X Treat the cleaned surface with hard wax.
Removing tar Remove any tar marks before washing the
vehicle.
X Apply tar remover with a soft cloth.
X Allow tar remover to work in briefly.
X Rub in gently.
X Rinse with plenty of water.
X Treat the cleaned surface with hard wax.
Vehicle washing In the winter, thoroughly remove all traces
of road salt as soon as possible.
When washing the vehicle underbody, do not forget to clean the inner sides of the
wheels.
Washing your vehicle by hand
X Wash the vehicle using car shampoo con-
centrate and a sponge.
X Rinse with clean water.
X Towel dry the vehicle. !
Do not wash the vehicle in direct sun-
light. The body panel surfaces and paint finish may be damaged.
Washing your vehicle in an automatic car
wash
i When running your vehicle through an
automatic car wash, water droplets can
run down the inside of the side windows.
Unscrew your vehicle’s antenna before
driving into an automatic car wash. X
Removing: Unscrew antenna :counter-
clockwise.
X Fitting: Screw antenna :in clockwise.
Power washer G
WARNING
Do not use a round nozzle (dirt grinders) to powerwash your vehicle, in particular the
tires. You could otherwise damage the tires
and cause an accident. 156
Vehicle care>> Operation.
Page 163 of 222
Display messages
The following display messages appear in the multifunction display (Y page 83).
You can confirm certain display messages.
X Confirming messages: Press the OK button on the control lever briefly (Y page 83).Display messages Possible causes/consequences and
M
MSolutions ?
Switch Off Engine Switch Off Engine The coolant is too hot.
In addition, the
?warning lamp in the instrument cluster
lights up and a warning signal sounds.
X Stop the vehicle immediately as soon as it is safe to do so.
X Switch off the drive system immediately.
X Engage the parking brake.
X Make sure the air supply for the radiator is uninterrupted.
X Only start the drive system again after the display message
disappears. You could otherwise damage the drive system. $
(USA only)
J (Canada only)
Release Parking Release Parking
Brake Brake You are driving with the parking brake engaged.
In addition, the $(USA only), J(Canada only) warning
lamp in the instrument cluster lights up and a warning signal sounds.
X Release the parking brake. $
(USA only)
J (Canada only)
Brake System See
Brake System See
Operator's Manual Operator's Manual There is a slight malfunction in the vacuum supply of the brak-
ing system.
X When braking, continue to depress the brake pedal.
X Contact an authorized electric drive smart center. $
(USA only)
J (Canada only)
Brake Malfunction
Brake Malfunction
Y Service Required
Service Required There is a serious malfunction in the vacuum supply of the
braking system.
In addition, a warning signal sounds.
X Contact an authorized electric drive smart center. 5
Shift Shift
to
toN
Nor
or P
Pto
to
Start
Start You have attempted to start the engine while the automatic
transmission was in reverse gear
Ror drive position D.
X Shift the automatic transmission into park position Por
neutral position N.
X Make sure that Nor Pis shown in the multifunction display. Display messages
161>> Practical hints. Z
Page 164 of 222
Display messages Possible causes/consequences and
M
MSolutions 5
Transmission Not Transmission Not
in P in P The driver's door is open and the gear selector lever is in
position
R,Nor D.
In addition, a warning signal sounds. X Move the gear selector lever to P.5
Malfunction Serv. Malfunction Serv.
Req. Req. There is a malfunction in the coolant compressor or in the
heating/coolant circuit.
X Contact an authorized electric drive smart center. 5
Battery Power Too Battery Power Too
Low Low The outside temperature is too low. The full battery capacity is
not available.
The vehicle does not start.
X Charge the high‑voltage battery (Y page 112).ÿ
High-voltage Bat‐ High-voltage Bat‐
tery at Reserve tery at Reserve
Level Level The high‑voltage battery has reached reserve level.
X Charge the high‑voltage battery (Y page 112).*
Charge HV Battery Charge HV Battery
Immediately Immediately The charge level of the high‑voltage battery is below 5 %.
In addition, a warning signal sounds.
X Charge the high‑voltage battery (Y page 112).N
Engine Engine
Restart
Restart Not
Not
Possible
Possible There is a serious malfunction in the drive system. The drive
system can no longer be started.
In addition, a warning signal sounds.
X Do not restart the drive system.
X Contact an authorized electric drive smart center. N
High-Voltage Sys‐ High-Voltage Sys‐
tem tem
Y Service Required
Service Required There is a malfunction in the drive system, the electric motor
or the high‑voltage battery. There is a high‑voltage safety
problem.
In addition, the Nwarning lamp in the instrument cluster
lights up and a warning signal sounds.
X Contact an authorized electric drive smart center. þ
Reduce Reduce
YSpeed Speed The vehicle speed exceeds 84 mph (135 kmh).
In addition, a warning signal sounds.
X Reduce the speed.
The message disappears. 162
Display messages>> Practical hints.
Page 165 of 222
Display messages Possible causes/consequences and
M
MSolutions þ
Drive System Drive System
Y Service Required Service Required There is a malfunction in the drive system, the electric motor
or the high‑voltage battery.
In addition, the yellow þwarning lamp in the instrument
cluster lights up.
X Contact an authorized electric drive smart center. þ
Drive System Drive System
Y Switch
Switch Engine
EngineOff
Off There is a malfunction in the drive train. If the drive system
continues to run, the drive train can become damaged.
In addition, the red
þwarning lamp in the instrument clus-
ter lights up and a warning signal sounds.
X Switch off the drive system.
X Do not continue driving.
X Contact an authorized electric drive smart center. *
Do Not Tow Do Not Tow
(Away)
(Away) Either the drive or the high‑voltage system is faulty.
In addition, the
Nwarning lamp in the instrument cluster
lights up.
X It is recommended to have the vehicle transported by a
qualified specialist workshop.
Do not tow the vehicle on its own wheels. *
Charging Charging
Not
NotPossi‐
Possi‐
ble
ble There is a malfunction in the on-board charger. The high‑volt-
age battery cannot be charged.
X Contact an authorized electric drive smart center. *
Parking Lock Inac‐ Parking Lock Inac‐
tive tive The gear selector lever is in position
P, but the parking lock is
not detected.
In addition, a warning signal sounds.
X Apply the parking brake.
X Move the gear selector lever to another position, e.g. to R.
X Move the gear selector lever to Pagain. Ö
Driver´s Door Ajar Driver´s Door Ajar The driver’s door is open.
X Close the driver’s door. Ø
Door Ajar Door Ajar The passenger door is open.
X
Close the passenger door. Õ
Tailgate Open Tailgate Open A tailgate or the rear soft top
9
is open.
X Close the tailgates or the rear soft. 9
cabriolet only. Display messages
163>> Practical hints. Z
Page 178 of 222
Loss of key
Problem Possible causes/consequences and
M
MSolutions You lose a key. X
Have the key deactivated at an authorized electric drive
smart center.
X Report the loss of the key to your car insurance company
immediately.
X If necessary, have the mechanical lock replaced.
Your authorized electric drive smart center will be glad to
supply you with a replacement following an identity check. Acoustic warning signals
Problem Possible causes/consequences and
M MSolutions A warning signal
sounds while driving. You are driving with the parking brake engaged.
X Release the parking brake (Y page 77).A warning signal
sounds when opening
the driver’s door. You have opened the driver’s door while the exterior lighting
is still switched on.
X Turn the exterior lamp switch to position $.A warning signal
sounds. The door is opened while a gear is engaged with the drive sys-
tem running and neither the brake nor accelerator pedals are
depressed.
X Close the driver’s and passenger door.
X Move the gear selector lever to park position P.
or
X Switch off the drive system. You open the driver’s door with the key in starter switch posi-
tion 0to remind you not to leave the key in the vehicle.
X Close the driver’s door.
or
X Remove the key from the starter switch. A warning signal
sounds. The seat belts are not fastened when the drive system is star-
ted. For details, see seat belt telltale (Y
page 168).
X Fasten your seat belts. 176
What to do if ...>> Practical hints.
Page 181 of 222
!
Check the polarity when inserting the
new transmitter battery. You could oth-
erwise damage parts of the electrical
system. When inserting the batteries,
make sure they are clean and free of lint.
X Insert the new transmitter battery.
X Press both halves of the key housing
together again.
X Check the operation of the remote con-
trol. Replacing bulbs
About replacing bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is
therefore essential that all bulbs and lamp
assemblies are in good working order at all times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. Contact an author- ized electric drive smart center for head-
lamp adjustment. G
WARNING
Bulbs and bulb sockets can be very hot.
Allow the lamp to cool down before changing a bulb. Otherwise you could be burned if you
touch them.
Keep bulbs out of the reach of children.
Halogen lamps contain pressurized gas. A
bulb can explode if you:
R touch or move it when hot
R drop the bulb
R scratch the bulb
Wear eye and hand protection.
i If the headlamps or front fog lamps* are
fogged up on the inside as a result of
high humidity, driving the vehicle a
distance with the lights on should clear
up the fogging. Notes on bulb replacement:
R Only use bulbs of the same type and with
the specified watt rating.
R Switch the lights off before replacing a
bulb to prevent short circuits.
R Always use a clean lint-free cloth when
handling bulbs.
R Your hands should be dry and free of oil
and grease.
R Avoid touching the glass of the bulb with
bare fingers.
R If the newly installed bulb does not come
on, contact an authorized electric drive
smart center.
R Have the bulbs for the front fog lamps*
and the LED daytime running lamps*
replaced at an authorized electric drive
smart center. Replacing bulbs
179>> Practical hints.
* optional Z