warning lights SMART FORTWO COUPE ELECTRIC DRIVE 2013 Owners Manual

Service and Literature
Your authorized electric drive smart
center has trained technicians and
Genuine smart Parts to service your vehicle
properly.
For expert advice and quality service,
contact an authorized electric drive smart
center.
For further information you can find us on
the smart web-site
www.smartusa.com(USA
only) or www.thesmart.ca (Canada only). G
WARNING
To help avoid personal injury, be extremely
careful when performing any service work
or repairs. Improper or incomplete service
or the use of incorrect or inappropriate
parts or materials may damage the vehicle
or its equipment, which may in turn result
in personal injury.
If you have any questions about carrying out
any type of service, turn to the advice of an
authorized electric drive smart center.
We reserve the right to make changes in
design and equipment.
Therefore, information, illustrations and
descriptions in this Operator’s Manual
might differ from your vehicle.
Reprinting, translation and copying, even
of excerpts, is not permitted without our
prior authorization in writing.
Symbols
Trademarks
®
:
R Bluetooth ®
is a registered trademark of
Bluetooth SIG Inc.
R ESP ®
is a registered trademark of
Daimler.
R iPod ®
is a registered trademark of Apple
Inc., registered in the U.S.A. and other
countries.
The following symbols are found in this
Operator’s Manual:
*O ptional equipment is identified with
an asterisk. Since standard equipment
varies between models, the
descriptions and illustrations in this
Operator’s Manual may differ slightly
from the actual equipment of your
vehicle. G
WARNING
Warning notices draw your attention to
hazards that may endanger your health or
life, or the health or life of others.
! Highlights hazards that may result in
damage to your vehicle.
i Helpful hints or further information
you may find useful.
X This symbol points to
instructions for you to follow.
X A number of these symbols
appearing in succession
indicates a multiple-step
procedure.
Y page This symbol tells you where you
can find additional information
on a topic within this Operator’s
Manual.
YY This continuation symbol marks a
warning or procedure which is
continued on the next page.
As at 10.02.2012

Driving
i The vehicle has acrawler function. The
vehicle moves forward when the brake
pedal is released.
X Depress the brake pedal.
X Move the gear selector lever to drive
position D.
D appears in the transmission position
indicator.
X Release the brake pedal.
The vehicle moves forward.
X Depress the accelerator pedal smoothly.
The vehicle accelerates. Reversing the vehicle
! Shift the transmission into reverse
gear Ronly when the vehicle is stopped
in order to avoid damaging the
transmission.
You can drive in reverse gear at a speed
of up to 9 mph (15 km/h).
i Das Fahrzeug verfügt über eine
Kriechfunktion. Bei Lösen des
Bremspedals fährt das Fahrzeug an.
X Depress the brake pedal.
X Move the gear selector lever to reverse
gear R.
R appears in the transmission position
indicator.
X Release the brake pedal.
Das Fahrzeug fährt an.
X Gleichmäßig Gas geben.
Das Fahrzeug beschleunigt. Parking
G
WARNING
With the drive system inactive, there is no
power assistance for the brake and steering
systems. In this case, it is important to
keep in mind that a considerably higher
degree of effort is necessary to brake and steer the vehicle
.Adapt your driving
accordingly. G
WARNING
Vehicle movement can cause serious
personal injury. Therefore, always do the
following before exiting and leaving the
vehicle:
R Keep right foot on the brake pedal.
R Engage the parking brake.
R Move the gear selector lever to park
position P.
R Slowly release the brake pedal.
R When parked on an incline, always turn
the front wheels towards the curb.
R Turn the key to starter switch position 0
and remove the key from the starter
switch.
R Take the key with you and lock the vehicle
when leaving.
X Properly stop and park the vehicle.
X Depress the brake pedal.
X Engage the parking brake (Y page 75).
When the ignition is switched on, the
brake warning lamp 0002(USA only) or
0001 (Canada only) in the instrument
cluster comes on.
X Release the brake pedal.
Parking brake The parking brake serves to secure the
vehicle against rolling away when it is
stationary or parked.
G
WARNING
Engaging the parking brake while the
vehicle is in motion can cause the rear
wheels to lock up. You could lose control of
the vehicle and cause an accident. In
addition, the vehicle’s brake lights do not
light up when the parking brake is engaged. Driving and parking
75>> Controls. Z

When doing so, observe that the display
and buttons on control element
002Aboth
point upwards.
Control element on the charging cable
(Level 1) G
WARNING
When connected to a power supply socket, a
high electrical load during the charging
process can lead to overheating of the
external power supply. There is a risk of
fire.
Find out about the maximum permissible
current load of the external power supply
socket for the respective country at an
authorized electric drive smart center.
Check the maximum permissible charge
current on site before you begin the
charging process. Contact an authorized
electric drive smart center should you
require assistance. If necessary, adjust
the settings of your vehicle.
! An excessive charge current can blow a
fuse or lead to overheating of the
external power supply. Check whether the
external power supply is compatible
with the set charge current. If necessary,
lower the set charge current or use
another power socket. 0002
AC status display
0003 Monitoring and safety system display
002B Charge current display
002A Set charge current button If the lights on indicator lamps
0002
and 0003light up, it means the following: Indicator lamp
0002 lights up
green The connection to the
external power supply is
OK. The high‑voltage
battery can be charged.
flashes red A malfunction is detected
in the external power
supply. The high‑voltage
battery will be charged
when the current signal
reaches a normal value.
lights up
red There is a malfunction.
The charging cable must
be unplugged from the
power socket and plugged
in again.
Indicator lamp
0003 lights up
green There is no malfunction.
The high‑voltage battery
can be charged.
lights up
red The power supply on the
control element is not
permissible. The
high‑voltage battery
cannot be charged.
i
Information on problems during the
charging process can be found on
(Y page 117).
X To set the charge current: press
button 002Arepeatedly until the desired
setting is selected in display 002B.
R An LED lights up: minimum setting
R All LEDs light up: maximum setting
i Depending on the country, the value of
the maximum setting may vary. High-voltage battery
113>> Operation. Z

Display messages
The following display messages appear in the multifunction displa y(Ypage 81). Display messages Possible causes/consequences and
0001 Solutions
0005
Switch Off Engine The coolant is too hot.
In addition, the
0005warning lamp in the instrument cluster
lights up and a warning signal sounds.
X Stop the vehicle immediately as soon as it is safe to do so.
X Switch off the drive system immediately.
X Engage the parking brake.
X Make sure the air supply for the radiator is uninterrupted.
X Only start the drive system again after the display message
disappears. You could otherwise damage the drive system. 0002
(USA only)
0001 (Canada only)
Release Parking Brake You are driving with the parking brake engaged.
In addition, the 0002(USA only), 0001(Canada only) warning
lamp in the instrument cluster lights up and a warning signal
sounds.
X Release the parking brake. 0002
(USA only)
0001 (Canada only)
Brake System See Operator's Manual There is a slight malfunction in the vacuum supply of the
braking system.
X
When braking, continue to depress the brake pedal.
X Contact an authorized electric drive smart center. 0002
(USA only)
0001 (Canada only)
Brake Malfunction 0001Service Required There is a serious malfunction in the vacuum supply of the
braking system.
In addition, a warning signal sounds.
X
Contact an authorized electric drive smart center. 0001
Shift
to N or P to
Start You have attempted to start the engine while the automatic
transmission was in reverse gear
Ror drive position D.
X Shift the automatic transmission into park position Por
neutral position N.
X Make sure that Nor Pis shown in the multifunction display. 0001
Transmission Not
in P The driver's door is open and the gear selector lever is in
position
R,Nor D.
In addition, a warning signal sounds.
X Move the gear selector lever to P. Display messages
155>> Practical hints. Z

Display messages Possible causes/consequences and
0001 Solutions
0001
Malfunction Serv.
Req. There is a malfunction in the coolant compressor or in the
heating/coolant circuit.
X
Contact an authorized electric drive smart center. 0001
Battery Power Too
Low The outside temperature is too low. The full battery capacity
is not available.
The vehicle does not start.
X
Charge the high‑voltage battery (Y page 108).0001
High-voltage
Battery at Reserve
Level The high‑voltage battery has reached reserve level.
X
Charge the high‑voltage battery (Y page 108).0007
Charge HV Battery
Immediately The charge level of the high‑voltage battery is below 5 %.
In addition, a warning signal sounds.
X
Charge the high‑voltage battery (Y page 108).0002
Engine
Restart Not
Possible There is a serious malfunction in the drive system. The drive
system can no longer be started.
In addition, a warning signal sounds.
X
Do not restart the drive system.
X Contact an authorized electric drive smart center. 0002
High-Voltage
System
0001Service Required There is a malfunction in the drive system, the electric motor
or the high‑voltage battery. There is a high‑voltage safety
problem.
In addition, the
0002warning lamp in the instrument cluster
lights up and a warning signal sounds.
X Contact an authorized electric drive smart center. 0001
Drive System
0001Service Required There is a malfunction in the drive system, the electric motor
or the high‑voltage battery.
In addition, the yellow
0001warning lamp in the instrument
cluster lights up.
X Contact an authorized electric drive smart center. 156
Display messages>> Practical hints.

Display messages Possible causes/consequences and
0001 Solutions
0001
Drive System
0001Switch Engine Off There is a malfunction in the drive train. If the drive system
continues to run, the drive train can become damaged.
In addition, the red 0001warning lamp in the instrument
cluster lights up and a warning signal sounds.
X Switch off the drive system.
X Do not continue driving.
X Contact an authorized electric drive smart center. 0007
Do Not Tow
(Away) Either the drive or the high‑voltage system is faulty.
In addition, the
0002warning lamp in the instrument cluster
lights up.
X It is recommended to have the vehicle transported by a
qualified specialist workshop.
Do not tow the vehicle on its own wheels. 0007
Charging Not
Possible There is a malfunction in the on-board charger. The
high‑voltage battery cannot be charged.
X
Contact an authorized electric drive smart center. 0007
Parking Lock
Inactive The gear selector lever is in position
P, but the parking lock
is not detected.
In addition, a warning signal sounds.
X Apply the parking brake.
X Move the gear selector lever to another position, e.g. to R.
X Move the gear selector lever to Pagain. 0001
Driver´s Door Ajar The driver’s door is open.
X
Close the driver’s door. 0002
Door Ajar The passenger door is open.
X
Close the passenger door. 0003
Tailgate Open A tailgate or the rear soft top
9
is open.
X Close the tailgates or the rear soft. 0003
Charge Cable
Connected The charging cable is inserted in the vehicle power socket.
The vehicle cannot be moved.
In addition, a warning signal sounds.
X
To drive off, remove the charging cable from the vehicle
power socket and stow the cable in the vehicle. 9
cabriolet only. Display messages
157>> Practical hints. Z

!
Check the polarity when inserting the
new transmitter battery. You could
otherwise damage parts of the electrical
system. When inserting the batteries,
make sure they are clean and free of lint.
X Insert the new transmitter battery.
X Press both halves of the key housing
together again.
X Check the operation of the remote
control. Replacing bulbs
About replacing bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is
therefore essential that all bulbs and lamp
assemblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. Contact an
authorized electric drive smart center for
headlamp adjustment. G
WARNING
Bulbs and bulb sockets can be very hot.
Allow the lamp to cool down before changing
a bulb. Otherwise you could be burned if you
touch them.
Keep bulbs out of the reach of children.
Halogen lamps contain pressurized gas. A
bulb can explode if you:
R touch or move it when hot
R drop the bulb
R scratch the bulb
Wear eye and hand protection.
i If the headlamps or front fog lamps* are
fogged up on the inside as a result of
high humidity, driving the vehicle a
distance with the lights on should clear
up the fogging. Notes on bulb replacement:
R
Only use bulbs of the same type and with
the specified watt rating.
R Switch the lights off before replacing a
bulb to prevent short circuits.
R Always use aclean lint-free cloth when
handling bulbs.
R Your hands should be dry and free of oil
and grease.
R Avoid touching the glass of the bulb with
bare fingers.
R If the newly installed bulb does not come
on, contact an authorized electric drive
smart center.
R Have the bulbs for the front fog lamps*
and the LED daytime running lamps*
replaced at an authorized electric drive
smart center. 172
Replacing bulbs>> Practical hints.
* optional

X
Remove the jumper cables from negative terminals 002Band 002Afirst.
X Remove the jumper cables from positive terminals 0002and 0003.
You can now switch on the headlamps.
X Remount the positive terminal cover.
X Have the 12-vol tbattery checked at the nearest authorized electric drive smart center.
i Please keep in mind that it will take quite some time to charge the 12-volt battery.
When you switch off the drive system after driving a short distance, you may not be able
to start it again.
Charge the 12-volt battery completely as soon as possible. Towing
About towing
This section offers information on towing
methods for breakdown situations and
emergency towing. Recommended towing method -
Breakdown situation
! To prevent damage during transport, do
not tie down the vehicle by its chassis or
suspension parts — use only wheel straps
to position and hold down the vehicle.
Improper tie down on a flatbed carrier
truck or trailer can damage suspension
parts and body panels.
smart recommends that the vehicle be
transported with all wheels off the ground
using a flatbed carrier truck or
appropriate wheel lift/dolly equipment.
Always have your vehicle transported:
R when the 0002warning lamp for the high-
voltage system lights up in the
instrument cluster
R when the Do not tow (away) message
appears in the instrument cluster
R when the multifunction display is
inoperative R
when one or several of the following
warning lamps light up:
-0001 Drive diagnostics (red)
- 0004 12‑Volt battery
0002 Power steering
R if the brake pedal already starts to
pulsate just after towing begins
R if you have to transport the vehicle over
long distances
X Switch off the tow‑away protection* and
interior motion sensor* (Y page 47). Emergency towing
When circumstances do not permit the
recommended towing method, the vehicle
may be towed with all wheels on the ground
using a strap or tow bar connected to
another vehicle. Only tow the vehicle as far
as necessary to have the vehicle moved to a
safe location where the recommended
towing method can be employed. 196
Towing>> Practical hints.
* optional