ignition SMART FORTWO COUPE ELECTRIC DRIVE 2014 Owner's Guide
[x] Cancel search | Manufacturer: SMART, Model Year: 2014, Model line: FORTWO COUPE ELECTRIC DRIVE, Model: SMART FORTWO COUPE ELECTRIC DRIVE 2014Pages: 222, PDF Size: 16.17 MB
Page 184 of 222
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
X Turn the exterior lamp switch to position
003F (Ypage 64).
X Switch off the ignition.
X Open the service flap (Y page 123).Left headlamp, (right headlamp in reverse)
Parking and side marker lamp bulb X
Removing:
Driver’s side: Turn bulb socket 0085toward
the outside.
Passenger side: Turn bulb socket 0085
toward the outside.
X Pull bulb socket 0085out of the headlamp
housing.
X Pull the bulb out of bulb socket 0085.
X Installing: Insert the new bulb into bulb
socket 0085.
X Insert bulb socket 0085into the headlamp
housing.
X Driver side: Turn bulb socket 0085toward
the inside.
Passenger side: Turn bulb socket 0085
toward the inside.
Low‑beam headlamp bulb X
Removing: Take off low‑beam headlamp
cover 0087.
X Detach the electrical connector. X
Bend the retainer spring end down and
forward until it unclips. Fold the
retainer spring back.
X Pull the bulb out of the headlamp hous-
ing.
X Installing: Insert the new bulb into the
headlamp housing.
X Fold the retainer spring forward.
X Bend the retainer spring end forward
then up and back to clip in.
X Attach the electrical connector.
X Reinstall low‑beam headlamp cover 0087.
High‑beam headlamp bulb X
Removing: Take off high‑beam headlamp
cover 0044.
X Detach the electrical connector.
X Tilt the bulb socket down and pull it out.
X Pull the bulb out of the bulb socket.
X Installing: Insert the new bulb into the
bulb socket.
X Fit the bulb so that the retaining lug of
the base plate is pointing up.
X Press the bulb into the bulb socket until
it is fully engaged.
X Attach the electrical connector.
X Reinstall high‑beam headlamp cover 0044.
Front turn signal lamp bulb X
Removing: Turn bulb socket 0043counter-
clockwise by a quarter of turn and pull it
out of the headlamp housing.
X Press gently onto the bulb and turn it
counterclockwise.
X Pull the bulb out of bulb socket 0043.
X Installing: Insert the new bulb into bulb
socket 0043.
X Press gently onto the bulb and turn it
clockwise.
X Insert bulb socket 0043into the headlamp
housing. 182
Replacing bulbs>> Practical hints.
Page 185 of 222
The arrow on bulb socket
0043must be in
line with the line on the headlamp hous-
ing.
X Turn bulb socket 0043clockwise by a quar-
ter of turn.
Side turn signal lamp bulb X
Removing: Open the door on the corre-
sponding side. X
Press on retaining lug 0043in the direc-
tion of the arrow until the side turn sig-
nal lamp housing disengages.
X Close the door.
X Use a suitable tool to loosen the side turn
signal lamp housing from the fender.
X Turn the bulb socket counterclockwise
and pull it out of the side turn signal
lamp housing.
X Pull the bulb out of the bulb socket.
X Installing: Insert the new bulb into the
bulb socket.
X Insert the bulb socket into the side turn
signal lamp housing and turn the bulb
socket clockwise.
X Fit the side turn signal lamp housing
onto the fender.
X Press gently onto the side turn signal
lamp housing.
The side turn signal lamp housing must
audibly engage. Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
X Turn exterior lamp switch to position
003F (Ypage 64).
X Switch off the ignition.
Tail lamp unit X
Removing:
Coupé: Open the upper tailgate.
X Open the lower tailgate.
X Cabriolet: Open the rear soft top
(Y page 72).
X Remove the side cover in the cargo com-
partment on the corresponding side.
X Fold the damping material forward, if
necessary. Left bulb carrier illustrated as example
0043
Retaining tab
0044 Electrical connector
X Press retaining tab 0043in the center of
the bulb carrier upwards.
X Pull the bulb carrier out of the tail lamp
housing. Replacing bulbs
183>> Practical hints. Z
Page 207 of 222
Front cover
Rear covers
X
Remove respective cover 0043or0044 using
a suitable object to reveal the threaded
hole for the towing eye bolt.
X Screw towing eye bolt in clockwise to its
stop and tighten with a suitable object. G
WARNING
For safety reasons, recovery or lashing
down of the vehicle by means of the towing
eye is not allowed. Failure to observe this
could result in the towing eye being ripped
out of its mounting and people being
injured.
Towing the vehicle X
Engage the parking brake.
X Connect the strap or tow bar to the towing
eye.
X Switch on the ignition.
X Depress the brake pedal and keep it
pressed. X
Move the gear selector lever to neutral
position N.
X Release the brake pedal.
X Switch on the hazard warning flasher.
X Release the parking brake.
Wait for at least 2 minutes after the vehicle
has been towed until start working on the
vehicle. Fuses
The electrical fuses in your vehicle serve
to switch off malfunctioning power cir-
cuits.
If a fuse is blown, the components and sys-
tems secured by that fuse will stop operat-
ing. G
WARNING
Only use fuses approved by smart with the
specified amperage for the system in ques-
tion and do not attempt to repair or bridge
a blown fuse this may cause an overload
leading to a fire, and/or cause damage to
electrical components and/or systems.
Contact an authorized electric drive smart
center if you encounter any electrical
problems.
! A blown fuse must be replaced by an
appropriate spare fuse (recognizable by
its color or the fuse rating given on the
fuse) of the amperage recommended in
the fuse chart. Any smart center will be
glad to advise you on this subject.
If a newly inserted fuse blows again, have
the cause determined and rectified at an
authorized electric drive smart center.
Before replacing fuses:
R Engage the parking brake.
R Make sure the gear selector lever is in
park position P.
R Turn off all electrical accessories. Fuses
205>> Practical hints. Z
Page 212 of 222
No. Accessory/Component Amperage Color
0080
Rear window defroster 40 A Orange
0081
Soft top (cabriolet only) 30 A Green
0082
Radiator cooling fan 40 A Orange
006A
Horn, central locking system 20 A Yellow
0069
— — —
0068
Starter switch (ignition) 50 A Red
0066
ESP
®
control unit 40 A Orange
00B7
EPS control unit 30 A Green
009A
Exterior rear view mirror heating 7.5 A Brown
009B
Brake lamps 7.5 A Brown
009C
— — —
009D
Tire pressure monitor control unit 7.5 A Brown
009E
Coolant pump, electric drive components, HV
interior PTC heater passenger compartment,
windshield unit car2go 10 A Red
009F
Audio, subwoofer, sound system, soft top
(cabriolet only) 15 A Blue
00A0
Interior lighting 5 A Light brown
00A1
Surround sound system 20 A Yellow
00A2
Seat heating control unit 25 A Neutral210
Fuses>> Practical hints.