service interval SMART FORTWO COUPE ELECTRIC DRIVE 2015 Owners Manual
[x] Cancel search | Manufacturer: SMART, Model Year: 2015, Model line: FORTWO COUPE ELECTRIC DRIVE, Model: SMART FORTWO COUPE ELECTRIC DRIVE 2015Pages: 222, PDF Size: 5.02 MB
Page 16 of 222
R
Corrosion Warranty
R California, Connecticut, Maine, Massa-
chusetts, New York, Pennsylvania, Rhode
Island, and Vermont Emission Control
System Warranty
R smartmove Assistance (Canada only)
R State Warranty Enforcement Laws (Lemon
Laws, USA only) Important notice for California retail
buyers and lessees of smart automo-
biles
Under California law you may be entitled to
a replacement of your vehicle or a refund of
the purchase price or lease price, if
Mercedes-Benz USA LLC and/or its author-
ized repair or service facilities fail to
fix one or more substantial defects or mal- functions in the vehicle that are covered by
its express warranty after a reasonable
number of repair attempts. During the
period of 18 months from original delivery
of the vehicle or the accumulation of
18 000 miles (approximately 29 000 km) on the odometer of the vehicle, whichever
occurs first, a reasonable number of repair
attempts is presumed for a retail buyer or
lessee if one or more of the following
occurs:
(1) the same substantial defect or mal- function results in a condition that is
likely to cause death or serious bodilyinjury if the vehicle is driven, that
defect or malfunction has been subject
to repair two or more times, and you
have directly notified Mercedes-Benz
USA LLC in writing of the need for its
repair,
(2) the same substantial defect or mal- function of a less serious nature than
category (1) has been subject to repair four or more times and you have directly notified us in writing of the
need for its repair, or
(3) the vehicle is out of service by reason of repair of the same or different sub-
stantial defects or malfunctions for a
cumulative total of more than 30 cal-
endar days.
Written notification should not be sent to a dealer, it should be addressed to:
Mercedes-Benz USA LLC
One Mercedes Drive
Montvale, NJ 07645 Maintenance
The Scheduled Maintenance Guide (USA) and
Service Booklet (Canada) describes all the
necessary maintenance work which should
be performed at regular intervals. It is
important that you service your vehicle in accordance with the prescribed mainte-
nance schedule. Failure to do so may render your vehicle unsafe, it may affect the dura-
bility of the vehicle, and it may otherwise
void the limited, express warranty.
Always have the Scheduled Maintenance
Guide (USA) or Service Booklet (Canada)
with you when you take the vehicle to your
authorized electric drive smart center for
service. The service advisor will record
each service in the booklet for you. Operating range
If you plan a long distance trip, please be
aware that:
R You will need to have access to an AC
power socket or a private wallbox to 14
>> Introduction.
Page 95 of 222
i
If the vehicle needs more time to charge
the high‑voltage battery than usual,
check the settings of the maximum per-
missible charge current. Messages menu
The Messages Messages menu stores messages that
you can call up.
i When no messages have been stored, the
Messages
Messages menu is not displayed. X
Press the control switch on the control
lever (Y page 83) up or down until the
Messages Messages menu appears in the multi-
function display.
The number of stored messages is :dis-
played
X Press the OK button on the control lever
briefly.
The first stored message appears.
X To scroll through messages: Press the OK
button on the control lever briefly.
For more information on display messages,
see (Y page 161).
Maintenance service interval display The maintenance service interval display
will notify you when the next maintenance
service is due and what type of maintenance
service is required.
Example:
R ° Main Service in XXX mi
Main Service in XXX mi
R ° Main Service in XX Days Main Service in XX Days
X To confirm: Press the OK button on the
control lever briefly.
The mesage is stored. When the due date for the maintenance ser-
vice has been has been passed, the number
of miles (kilometers) or days since are
preceeded by a minus sign.
! Failure to have the maintenance ser-
vice performed at the designated times/
mileage, may result in vehicle damage
that is not covered by the smart Limited
Warranty. Settings menu
In the Settings Settings menu, you can select indi-
vidual settings for your vehicle.
The following functions are available:
R Setting the language
R Setting the temperature unit
R Setting the distance and speed unit
X Press the control switch on the control
lever (Y page 83) up or down until the
Settings
Settings menu appears in the multi-
function display.
X Press the OK button on the control lever
briefly.
Setting the language The following languages are available:
R German
R US English
R UK English
R French
R Italian
R Spanish X
Press the control switch on the control
lever (Y page 83) up or down until the Control system
93>> Controls. Z
Page 129 of 222
X
Push cap :onto the windshield washer
reservoir.
X Remount the service flap and close it
(Y page 123). Brake fluid
G
WARNING
During vehicle operation, the boiling
point of the brake fluid is continuously
reduced through the absorption of moisture from the atmosphere. Under extremely
strenuous operating conditions, this mois-
ture content can lead to the formation of
bubbles in the system, thus reducing the
system’s efficiency.
Therefore, the brake fluid must be replaced regularly. Refer to your vehicle’s Mainte-
nance Booklet for replacement interval.
The brake fluid level in the brake fluid
reservoir may be too low if the brake warn- ing lamp in the instrument cluster comes on(Y page 23) although the parking brake is
released.
! If you find that the brake fluid in the
brake fluid reservoir has fallen to the
minimum mark or below, have the brake
system checked for brake pad thickness
and leaks immediately. Contact an
authorized electric drive smart center
immediately. Do not add brake fluid as
this will not solve the problem.
X Remove the service flap and insert it on
the front of the vehicle (Y page 123).
The brake fluid reservoir is located in the
front compartment on the passenger side. Checking brake fluid level
X
Perform a visual check of the brake fluid
reservoir :.
The brake fluid level is correct when it
is between the minimum mark and the
maximum mark. R If the brake fluid level has fallen
slightly below the minimum mark,
drive to an authorized electric drive
smart center.
R If the brake fluid level has fallen sig-
nificantly below the minimum mark,
call Roadside Assistance or an author- ized electric drive smart center.
X Remount the service flap and close it
(Y page 123). Tires and wheels
Safety notes
Contact an authorized electric drive smart
center for information on tested and rec-
ommended rims and tires for summer and
winter operation. They can also offer
advice concerning tire service and pur-
chase. G
WARNING
Replace rims or tires with the same desig- nation, manufacturer and type as shown on
the original part. For further information
contact an authorized electric drive smart
center. If incorrectly sized rims and tires are mounted, the wheel brakes or suspen- Tires and wheels
127>> Operation.
Z
Page 150 of 222
keep in mind that a considerably higher
degree of effort is necessary to brake and
steer the vehicle. Adapt your driving
accordingly. Brakes
G
WARNING
Make sure not to endanger any other road
users when carrying out braking maneu-
vers.
Refer to the description of the hydraulic
brake assistant (Y page 47).
! Because the ESP ®
operates automati-
cally, the ignition must be switched off
when the parking brake is being tested
on a brake test dynamometer. Active
braking action through the ESP ®
may oth-
erwise seriously damage the brake sys-
tem which is not covered by the smart
Limited Warranty.
Brake pad wear or a leak in the brake system may be the reason for low brake fluid level
in the brake fluid reservoir.
The brake fluid level in the brake fluid
reservoir may be too low if the brake warn- ing lamp in the instrument cluster comes on
(Y page 23) although the parking brake is
released.
Have the brake system inspected immedi-
ately. Contact an authorized electric drive
smart center.
All checks and service work on the brake
system should be carried out by qualified
technicians only. Contact an authorized
electric drive smart center.
Only install brake pads and use brake fluid
recommended by smart. Inclines G
WARNING
Resting your foot on the brake pedal will
cause excessive and premature wear of the
brake pads.
It can also result in the brakes overheat-
ing, thereby significantly reducing their
effectiveness and your ability to stop the
vehicle in sufficient time to avoid an acci- dent.
Please observe the following guidelines to
avoid that the permitted maximum speed is
exceeded when driving on downhill grades:
R Do not move the gear selector lever to N.
R Recuperation is limited, if:
- the high-voltage battery is fully
charged or too cold
- the power electronics or the electric
motor is overheated.
When driving down long and steep grades, do not depress the brake pedal perma-
nently. Depress it in intervals instead to
reduce the vehicle speed.
High and low stresses After hard braking, it is advisable to drive
on for some time, rather than immediately
park, so that the air stream will cool down
the brakes faster.
If your brake system is normally only sub-
jected to moderate loads, you should occa- sionally test the effectiveness of the
brakes by applying above-normal braking
pressure at higher speeds. This will also
enhance the grip of the brake pads. G
WARNING
Make sure not to endanger any other road
users when carrying out these braking
maneuvers. 148
Driving instructions>> Operation.
Page 199 of 222
G
WARNING
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque of
80 lb-ft (110 Nm).
i The Tire Pressure Monitoring System
(TPMS)* only functions on wheels that are
equipped with the proper electronic
sensors (Y page 130). Batteries
Notes on the vehicle’s electrical sys-
tem
The vehicle’s electrical system provides
power for the electric drive and all elec-
trical consumers or components of the
vehicle.
Power is supplied to the vehicle via two
batteries:
R 12-volt battery
R High-voltage battery Notes on the 12‑volt battery
Your vehicle’s 12‑volt battery is located in
the passenger footwell below the footrest
(Y page 199).
The 12 volt battery should always be suffi-
ciently charged in order to achieve its
rated service life. Refer to the Scheduled
Maintenance Guide (USA only) or the Ser-
vice booklet (Canada only) for battery
maintenance intervals.
If you use your vehicle mostly for short-
distance trips, you will need to have the
12 volt battery charge checked more fre-
quently.
When replacing the battery, always use bat-
teries approved by smart. For information,
contact an authorized electric drive smart
center. If you do not intend to operate your vehicle
for an extended period of time, consult an
authorized electric drive smart center
about steps you need to observe. G
WARNING
Observe all safety instructions and pre-
cautions when handling automotive batter- ies. Risk of explosion.
Fire, open flames and
smoking are prohibited
when handling batteries.
Avoid creating sparks.
Battery acid is caustic.
Do not allow it to come
into contact with skin,
eyes or clothing.
Wear suitable protective
clothing, especially
gloves, apron and face-
guard. Wear eye protection.
Rinse any acid spills
immediately with clear
water. Contact a physician
if necessary. Keep children away.
Follow the instructions in
this Operator’s Manual. G
WARNING
Failure to follow these instructions can
result in severe injury or death.
Observe all safety instructions and pre-
cautions when handling automotive batter- ies.
Never lean over batteries while connect-
ing, you might get injured. Batteries
197>> Practical hints.
* optional Z
Page 220 of 222
Capacities
Components Capacity Coolants, lubricants, etc.
Coolant system approx. 6.9 US qt (6.5 l) Anticorrosion/Antifreeze meet-
ing specification MB 325.0
Air conditioning system 500 g
(17.6 oz) R134a refrigerant (never R 12)
120 g
(4.2 oz) PAG lubricant oil Daphne 1234
Windshield washer sys-
tem 4.0 US qt (3.8 l)
Windshield washer concentrate
13
(Y page 218)
Washer fluid mixing ratio
(Y page 218) Brake fluid
G
WARNING
During vehicle operation, the boiling
point of the brake fluid is continuously
reduced through the absorption of moisture from the atmosphere. Under extremely
strenuous operating conditions, this mois-
ture content can lead to the formation of
bubbles in the system, thus reducing the
system’s efficiency.
Therefore, the brake fluid must be replaced regularly. Refer to your vehicle’s Mainte-
nance Booklet for replacement interval.
Only brake fluid approved by smart is rec- ommended. Any authorized electric drive
smart center will provide you with addi-
tional information. Windshield/rear window washer system
During all seasons: X Use a windshield washer concentrate
labeled for summer and water for tem-
peratures above freezing point.
X Use a windshield washer concentrate
labeled for winter and water for temper-
atures below freezing point.
X Premix the windshield washer fluid in a
suitable container depending on the out-
side temperature and in accordance with
the manufacturer’s instructions 14
.
Washer fluid mixing ratio R
Temperature above 32¦ (0¥):
1 part windshield washer concentrate
labeled for summer to 100 parts water
R Temperature of 14¦ (-10¥):
1 part windshield washer concentrate
labeled for winter to 2 parts water
R Temperature of -4¦ (-20¥):
1 part windshield washer concentrate
labeled for winter to 1 part water
13 Use a windshield washer concentrate labeled for summer and water for temperatures above freezing
point or a windshield washer concentrate labeled for winter and water for temperatures below freezing
point.
14 Refer to the notes for use on the container. 218
Service fluids and capacities>> Technical data.
Page 221 of 222
G
WARNING
Windshield washer concentrate is highly
flammable. Fire, naked flames and smoking
are prohibited when windshield washer
concentrate is being handled. Coolants
The battery and drive system coolant is a
mixture of water and anticorrosion/anti-
freeze, which provides: R Corrosion protection
R Freeze protection
R Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory with a coolant providing freeze protection
to approximately -35¦ (-37¥) and corro-
sion protection.
! Add premixed coolant solution only.
Adding water and MB 325.0 Anticorro-
sion/Antifreeze separately from each
other, could cause drive system damage
not covered by the smart Limited War-
ranty.
If the antifreeze mixture is effective to
-35¦ (-37¥), the boiling point of the
coolant in the pressurized cooling system
is reached at approximately 266¦ (130¥).
The coolant solution must be used year
round, even in countries which have high
temperatures to provide the necessary cor-
rosion protection and increase boil‑over
protection. Refer to Maintenance/ Service
Booklet for replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solu-
tion or other smart approved products of
equal specification are used to renew the
coolant concentration or bring it back up
to the proper level. For information on other smart approved
products of equal specification, contact an
authorized electric drive smart center.
To provide important corrosion protec-
tion, the solution must be at least 50% anti-
corrosion/antifreeze (equivalent to freeze
protection to approximately -35¦
[-37¥]).
If you use a solution that is more than 55%
anticorrosion/antifreeze (freeze protec-
tion to approximately -49 ¦[(-45¥ ]), the
drive system and battery temperature will
increase due to the lower heat transfer
capability of the solution. Therefore, do
not use more than this amount of anticor-
rosion/antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze should
be used to bring it up to the proper level
(have cooling system checked for signs of
leakage). Please make sure the mixture is
in accordance with label instructions.
Always use anticorrosion/antifreeze that
has been approved by smart. For informa-
tion contact an authorized electric drive
smart center.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water.
If you are not sure about the water quality, consult an authorized electric drive smart
center.
Capacities Cooling-system
capacity
All models approx. 6.9 US qt
(6.5 l)
Anticorrosion/antifreeze
Your vehicle contains a number of alumi-
num parts. The use of aluminum components
in motor vehicle drive systems necessi-
tates that anticorrosion/antifreeze cool- Service fluids and capacities
219>> Technical data. Z