turn signal SSANGYONG KORANDO 2012 Owners Manual

07-118310-00
Approach (puddle) lamp
(7) Puddle (approach) lamp
Approach lamp ON 1.Lamp control for models with SKM ▶
When turning the ignition switch to OFF from ON position and opening the driver door, the
approach lamps come ON.
When receiving the UNLOCK signal from the smart key remote control or outside door handle
switch signal in the theft deterrent mode, the approach lamps come ON for 30 seconds.
When receiving the AUTO approach signal in the theft deterrent mode, the approach lamps come
ON for 30 seconds. -
-
-
Approach lamp OFF 2.
When receiving the door lock signal from the smart key remote control or outside door handle
switch signal with the approach lamps ON, the lamps go OFF (reactivation of theft deterrent
mode).
When turning the ignition switch to ON position with the approach lamps ON, the lamps go OFF.
The approach lamps go OFF after 30 seconds. -
-
- Approach lamp ON 1.Lamp control for models without SKM ▶
When receiving the UNLOCK signal in the theft deterrent mode, the approach lamps come ON for
30 seconds.
When turning the ignition switch to OFF from ON position and opening the driver door, the
approach lamps come ON. -
-
Approach lamp OFF 2.
When receiving the door lock signal with the approach lamps ON, the lamps go OFF (reactivation
of theft deterrent mode).
When turning the ignition switch to ON position with the approach lamps ON, the lamps go OFF.
The approach lamps go OFF after 30 seconds. -
-
-

07-14
2) Operation
(1) Front room lamp/Center room lamp
Front room lamp Center room lamp
Operating the front room lamp and center room lamp switches illuminates the driver/passenger side
lamps and center room lamp.
Room lamp control by door coupled room lamp operation ▶
If a door except the tailgate is opened after the ignition is turned off, provided that door coupled front
room lamp switch is pressed, the front room lamp and center room lamp are illuminated for 2 sec.
and then fade out for 3 sec.
If a door except the tailgate is opened and then closed while the room lamp is fading out, the room
lamp is illuminated for 2 sec. and then fades out for 3 sec. If the ignition is turned on, the room lamp
goes off immediately.
The front room lamp and center room lamp are illuminated for 30 sec. when the door is unlocked by
the REKES or passive door UNLOCK function with IGN OFF and the ignition key removed. If the
REKES or passive door UNLOCK signal is received again, the room lamps are illuminated for
another 30 sec.
The room lamp goes off immediately when the REKES or passive door LOCK signal is received or
the ignition switch is turned to ON position.
If the room lamp is turned on after the ignition key is removed (door open or room lamp switch is
pressed), it is turned off after 10 minutes by the BCM.
When the door open state is changed or the ignition is turned on after the room lamp has been turned
off automatically, the battery saver feature is reset. 1.
2.
3.
4.
5.

08-137810-00
(1) Wiper mist
When the multifunction switch is pushed to the MIST position for 0.1 sec. or more with the IGN1 ON,
the wiper relay is turned on after 0.1 sec. has passed. When the wiper returns to the park position, the
wiper relay is turned off.
When the MIST switch signal is input the wiper is operated at high speed. When the switch is release
from the MIST position, the wiper is operated at low speed. 1.
2.

08-14
(2) Wiper LO/HI control
The wiper LOW relay is turned on when the multifunction wiper switch is at the LO position. The wiper
HIGH relay is turned on when the wiper switch is at the HI position. When the wiper switch is at the HI
position, both the LOW relay (constant operation) and HIGH relay are operated.
The wiper motor returns to parking position and stops, even when turning off the ignition switch during
wiper operation.
The wiper relay should stay ON in low/high wiper operation mode even if the parking signal for the
wiper motor is not received. In INT/AUTO wiper operation mode, the wiper relay should be turned
OFF after 5 seconds if there is no parking signal for the wiper for 3 seconds and informs the driver of
parking position signal abnormality.
While the wiper operates at low/high speed, the front/rear washer switch can be operated but the auto
washer switch cannot.
The wiper motor returns to parking position and stops when turning off the ignition switch during wiper
operation in high mode. 1.
2.
3.
4.
5.

08-177810-00
When the AUTO washer switch is operated with IGN ON and the INT/AUTO switch OFF, the
washer motor is operated for 2 sec. and the wiper continues to cycle 4 times. And then the washer
motor is operated for 2 sec. and the wiper continues to cycle 3 times before returning to park
position.
The auto washer switch signal is overridden during speed sensitive intermittent wiper, washer
coupled wiper or auto washer coupled wiper operation.
When turning the wiper switch to AUTO position during the operation of auto washer, the auto
washer stops its operation and the intermittent/automatic wiping mode will be started.
The front and rear washer switch signal are overridden during the operation of auto washer.
The input from the switch during the AUTO washer coupled wiper operation also is ignored. 1.
2.
3.
4.
5.
(2) AUTO washer coupled wiper
Auto washer switch
If pressing the switch when the wiper switch turns
to the "OFF" position, washer fluid is sprayed
once and wiper operates 4 times.
After a while, washer fluid is sprayed once more
and the wiper operates 3 times.

08-197810-00
4) Rear Washer Control Function
The rear washer motor is operated only when the rear washer switch is activated with the ignition
key ON.
If the front washer or automatic washer switch signal is received during the rear washer switch
operation, the washer motor stops and the front washer or automatic washer motor begins to
operate. 1.
2.Rear washer motor control ▶
When the switch is fully turned, washer fluid
will be sprayed onto the rear window glass
and the wiper will also operate. When the
switch is released, it will return to the “OFF
"
position and turn off the wiper and washer.

08-22
If the intermittent/automatic wiper switch is in "ON" position, the wiper motor does not operate even
when turning the ignition switch to ON from OFF position.
When the INT/AUTO wiper switch is turned on from off with the ignition switch ON, the wiper is
operated at low speed for the 1st cycle regardless of the rain sensor signals. After that, if the
INT/AUTO wiper switch is turned on from off, the wiper cycles one time at low speed only when the
rain sensor detects the presence of rain. 1.
2.
(2) Power-up reminder wiper

08-26
When the wiper speed control switch is turned to step 3 from step 4 the wiper motor cycles one time
at low speed, provided that the BCM receives a communication error signal from the rain sensor uni
t
with IGN ON and the INT/AUTO switch ON. 2.
When the wiper speed control switch is turned to step 2 from step 3 the wiper motor cycles one
time at low speed, provided that the BCM receives a faulty sensor signal from the rain sensor unit
with IGN ON and the INT/AUTO switch ON. 1.
(6) For faulty rain sensor

09-6
IP display (SVC only)
When the gear selector lever is shifted into “R", the parking aid system is activated and three
sensors in the rear bumper detect the distance to any obstacle. The PAS detects the returning signals
reflected to the obstacles at regular intervals when the vehicle is parked to indicate the display and alarm
for the distance between the obstacles by phase so as to allow the driver easy parking by securing safe
distance.
1. OVERVIEW
Buzzer for PAS
Buzzer sounds using instrument
cluster buzzer
Rearview cameraShift lever

09-12
4. OUTPUT SPECIFICATIONS FOR SENSOR SELF-
DIAGNOSIS BUZZER SOUND
Fail condition (However, no obstacle should be within 30 cm)
1. The signal wire is open
2. The power wire (+ and -)is open -Conditions to "FAIL" in sensor diagnosis ▶Buzzer interval during self diagnosis ▶
Timeout processing time for buzzer interval after measuring distance/self diagnosis: 600 ms
- If timeout is reached, the PAS returns to undetected condition.
Process while re-inputting
- After timeout, the process is performed normally if the signal required for display is received
from beginning to end. (not detectable if the signal is received in the midst of process) 1.
2.Exception/error handling ▶ Self diagnosis is performed once when the ignition is switched on (gear shift lever in "R" position). If the
system is defective (Fail) due to open sensor or communication problem, the information for the failed
sensor is displayed as buzzer sound.
If it is normal, the warning buzzer sounds for 60 ms.