lock SSANGYONG KORANDO 2012 Manual Online

04-28
Smart key not found warning deactivation conditions
If below conditions are met, the SKM sends the signal for [Smart key not found warning
deactivation] to deactivate the warning. -
A smart key is found while the smart not found warning signal is output.
OR 1.
2.
(2) Smart key detection warning
When a valid smart key sends the LOCK signal from outside of the vehicle or the outside door handle
switch is pressed with no smart key outside, the smart key detection warning signal is output, provided
that all the doors or the tailgate is closed with IGN OFF or ACC ON and a smart key is in the vehicle.
Smart key detection warning conditions ▶
When a valid smart key sends the LOCK signal from outside of the vehicle, the SKM sends the signals
for [external buzzer] and [smart key detection warning] to the BCM and instrument cluster through the
BCAN to inform the driver of the existence of a verified key inside the vehicle, provided that all the doors
or the tailgate is closed with IGN OFF or ACC ON and a smart key is in the vehicle.
Smart key inside vehicle warning 2.
If a smart key including immobilizer slot is identified as being in the vehicle after the outside door handle
switch is pressed, the SKM sends the signals for [external buzzer] and [smart key detection warning] to
the BCM and instrument cluster through the BCAN to inform the driver of the existence of a verified key
inside the vehicle.
These 2 warnings (external buzzer, smart key detection warning) continue for up to 10 sec. until the
warning conditions are deactivated under the above conditions.
The SKM stops these warnings immediately after the warning conditions are deactivated. -
Smart key detection warning deactivation conditions ▶Deactivation warning 1.
Function stop warning deactivation conditions 1.
When theft deterrent deactivated
The SKM sends the signals for [external buzzer] and [smart key detection warning
deactivation].
Smart key inside vehicle warning deactivation conditions
When the door is opened and then closed and no smart key is found, the SKM sends the
signals for [external buzzer] and [smart key detection warning deactivation]. -
-

05-158010-01
Indicator
(green)
Hazard indicator ▶
ECO indicator ▶
Cruise control indicator ▶
Indicator
(red)
Indicator
(green)
Indicator
(green)
4WD LOCK indicator ▶
Indicator
(red)
4WD check warning lamp ▶This indicator comes on when the cruise control system is activated.
This indicator goes off when the brake pedal is depressed. (auto cruise
deactivated)
This warning lamp comes on when the 4WD LOCK switch is pressed.
This indicator goes off when pressing the switch again.
This warning lamp comes on when the 4WD system is defective. This indicator comes on when the hazard warning flashers are switched on.
(applies to STD class)
This indicator comes on when the ECO cruise system is activated.
This indicator goes off when the brake pedal is depressed. (ECO
deactivated)

05-20
SVC ▶
3) Block Diagram

05-318010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch to
ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

05-338010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch
to ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

05-46
Pin No.Message
Operating condition
Domestic Export
Smart key
warningThis message comes on the LCD display, if the smart
key is not in the vehicle when the door is open and
closed in the ignition ON or ACC mode.
This message comes on the LCD display for approx. 10
seconds, if the ignition switch is pressed when the smart
key is not in the vehicle.
This message comes on the LCD display for approx. 10
seconds, if the smart key verification fails after inserting
the smart key into the key holder.
This message comes on the LCD display for approx. 10
seconds with warning sound if the smart key is in the key
holder when the driver door is open with ignition OFF.
This message informs the driver that the brake pedal
should be depressed and the ignition switch be pressed
in order to start the engine, if the ignition is switched to
ACC mode for more than one time when the driver keeps
pressing the ignition switch without depressing the brake
pedal.
This message informs the driver that the clutch pedal
should be depressed and the ignition switch be pressed
in order to start the engine, if the ignition is switched to
ACC mode for more than one time when the driver keeps
pressing the ignition switch without depressing the clutch
pedal.
This message comes on for approx. 10 seconds to
inform the driver that the ignition switch should be
pressed with the shift lever in P in order to start the
engine.
This message comes on for approx. 10 seconds to
inform the driver that the verified smart key is in the
vehicle, if the driver locks the door using another verified
smart key with all the doors closed.
Pin No. Message Operating condition

06-8
Power window main switch
1) Driver Door Switches
2. SWITCH CLUSTER ON DOOR TRIM
(1) Power window main switch
Driver door window switch
Rear LH window switch Window lock switch Passenger door window switchRear RH window switch
Door lock/unlock switch

06-98510-00
Door lock/unlock switch
When the door lock/unlock switch
is pressed while all doors
including the tailgate are locked,
all doors will be unlocked. When
the switch is pressed again, all
doors will be locked.Window lock switch
If the window lock switch is
pressed down, only driver window
is operative. Passenger and rear
windows cannot be operated by
their switches.
Rear LH window
switch
The window is up and down
while this switch is operated.
Passenger door
switch
The window is up and down
while this switch is operated.
Rear RH window
switch
The window is up and down
while this switch is operated.
Driver door window switch
The driver's door window switch has Auto down/Auto up function. The
window can be controlled within 30 seconds by activating the power
window relay even after turning off the ignition switch.
However, if any of front doors is opened or the Lock switch on the
remote control key is pressed (theft deterrent mode is activated)
during the delaying period, the delaying time is immediately canceled
(power window relay is deactivated).
There are two variants of this: only auto down and anti-trap (auto
down and auto up).

06-10
Time lag power window control ▶
When turning the ignition switch to ON position, the power window relay is turned ON.
The power window relay keeps ON for 30 seconds even when stopping the engine.
However, the power window relay is turned OFF when opening a front door.
When locking the door (activation of theft deterrent mode), the power window relay is immediately
turned OFF. 1.
2.
3.

06-118510-00
Door lock/unlock switch
Function of door lock/unlock switch ▶
There are 5 actuators in door lock/unlock system (including tailgate). All of them can control the
corresponding door lock and unlock separately. But, the driver door lock switch can control all door
locks. The BCM controls the lock/unlock switch using the door lock/unlock relay. This is a same control
type with Auto door lock function that locks the doors when the vehicle speed exceeds 30 km/h. (see
circuit diagram)
Door lock/unlock relay (integrated in BCM) ▶
Door lock/unlock switch
When the door lock/unlock switch is pressed while all doors including the tailgate are locked, all doors
will be unlocked. When the switch is pressed again, all doors will be locked.