heating SSANGYONG KORANDO 2013 Owner's Manual

Center fascia switch
2) Center Fascia Switch
This helps the driver to drive the vehicle comfortably by operating the switch for the driving situation. It
consists of the windshield heating switch, TRIP/RESET switch, rear glass/outside rearview mirror
heating switch and hazard warning flasher switch.
Windshield heating switch
TRIP/RESET switch
Rear glass/outside rearview mirror heating switch
Hazard warning flasher switch A.
B.
C.
D.

8510-00
Windshield heating switch
Press this switch to operate the windshield
heating system for 12 minutes. Press the
switch again to stop the system. The
heated glass will operate for about 6
minutes when the switch is pressed again
within 10 minutes after completion of its
first operation cycle. The indicator lamp for
the switch comes on when the heating is
on.
Hazard warning flasher switch
When the driver presses the switch, all the
turn signal lamps flash regardless of the
ignition switch status. Pressing the switch
again turns off the turn signal lamps. The turn
signal lamp does not operate while the
hazard warning flasher operates.
TRIP/RESET switch
Whenever pressing this button, the information is
displayed in the following order: Odometer, Trip
A, Trip B, Distance to empty, Average fuel
economy, Instant fuel economy, Illumination level,
Tire pressure (with TPMS), Ambient air
temperature (for STD); Trip A, Trip B, Distance to
empty, Average fuel economy/Instant fuel
economy, Illumination level, Tire pressure (with
TPMS), Ambient air temperature (for SVC). Press
and hold this button to initialize (reset) Trip A/Trip
B and average fuel consumption, adjust
illumination level or change the unit of
temperature.
Description
Rear glass/outside rearview mirror heating
switch
Press this switch to operate the rear glass and
outside rearview mirror heating system for 12
minutes. Press the switch again to stop the
system. The heated glass will operate for about 6
minutes when the switch is pressed again within
10 minutes after completion of its first operation
cycle. The indicator lamp for the switch comes on
when the heating is on.
The switch is operable only when the engine
is started.
The hazard warning flasher blinks
during emergency hazard warning
lamp control and air bag deployment
signal activation.
The switch is operable only when the
engine is started.

(1) Rear glass/outside mirror heating switch
Overview
The rear glass/outside mirror heating is operated by BCM.
The heating operates for about 12 minutes when the switch is pressed with the engine started.
Press the switch again to stop the operation.
The output is "ON" only for 6 minutes when turning on the rear defogger switch within 10 minutes after
completion of output for 12 minutes. This can be done only once.
This function is available only when the engine is running.
Operation curve

8510-00
(2) Windshield heating switch
The windshield glass/outside mirror heating is operated by BCM.
The heating operates for about 12 minutes when the switch is pressed with the engine started.
Press the switch again to stop the operation.
The output is "ON" only for 6 minutes when turning on the rear defogger switch within 10 minutes after
completion of output for 12 minutes. This can be done only once.
This function is available only when the engine is running.
Operation curve

Lower main panel switch
3) Lower Main Panel Switch
Rear fog lamp switch (EU ONLY)
Steering wheel heating switchHLLD (Headlamp Leveling Device)4WD LOCK switch
ESP OFF switch This helps the driver to drive the vehicle comfortably by operating the switch for the driving situation.

8510-00
4WD LOCK switch
This switch is of push lock type, which
enables to increase/decrease the
torque to the rear wheels in AWD
mode.
Steering wheel heating
switch
This switch is of push return type,
which is used to activate or deactivate
the steering wheel heating function.
ESP OFF switch
The ESP OFF switch is of push return
type, which is used to stop or resume
the ESP function.
4WD LOCK switch
This switch is of push lock type, which
enables to increase/decrease the
torque to the rear wheels in AWD
mode.
HLLD
(Headlamp Leveling Device)
The headlamp aiming can be adjusted
by using this dial-type switch.
Rear fog lamp switch
(EU ONLY)
This switch is of push return type,
which sends ON/OFF signal to the
BCM so that the BCM can switch on
the lamps by activating the rear fog
lamp relay.

8510-00
Steering wheel heating switch
The steering wheel heating switch is mounted to the lower main panel. In that, signal voltage from the
steering wheel heating controller, which is installed in the steering wheel, is grounded. This is used as
an operation signal for the steering wheel heating system. The indicator in the switch comes on when it
is operated.
Steering wheel heating switch
(3) Operation process

8510-00
Front seat heating and ventilation switch (2-
level of driver seat heating and ventilation, 2-
level of passenger seat heating)
A. Driver seat heating switch
B. Driver seat ventilation switch
C. Passenger seat heating switch
5. SEAT HEATING AND VENTILATION SWITCH
1) Front Seat Heating and Ventilation Switch Overview (2-level of
Driver Seat Heating and Ventilation, 2-level of Passenger Seat
Heating)
The temperature of the seat can be adjusted in 3
seat heated wire and ventilation switch. Every
time the seat heating and ventilation switch is
pressed, the temperature level goes down by
one level. Pressing the switch a third time will turn
off the operation. Pressing the desired side of the
switch heats the seat cushion and seatback or
activates the seat ventilation function. The
temperature of the seat is kept uniform by cutting
off or connecting power through thermistor fitted
in the seat. The seat heating and ventilation unit
controls the rpm of the motor using PWM control
to operate the seat ventilation.
Front seat heating & ventilation switch (2-level of driver seat heating and ventilation, 2-level of
passenger seat heating)-
-
The front seat heating and ventilation functions cannot be operated at the same time.
The front seat heating and ventilation switch functions only when the engine is started. -
-Seat heating and ventilation unit & switch application

Front seat heating switch
A. Driver seat heating switch
B. Passenger seat heating switch
Rear seat heating switch
A. Rear LH seat heating switch A. Rear RH seat heating switch
The front seat heating switch can be operated to
the desired temperature (LO/HI) by pressing the
the seat heating switch to heat the seat and
seatback. When the temperature reaches 40
connects and cuts the power to keep the
temperature stable. There is no separate seat
warmer unit to control the temperature of the seat
heating system.
2) Front Seat & Rear Seat Heating Switch Overview
LH RH
The front seat and rear seat heating switches operates with IGN ON.
The seat heating and ventilation unit is not fitted in a vehicle without seat ventilation function. -
-

Ensure that the connection or disconnection between the audio system and the USB memory/iPod
is carried out only when the engine is switched off. If the engine is switched on or off while the USB
memory is connected or disconnected, the USB memory may be damaged or not operate normally.
The audio system may not recognize some USB memory depending on the comparability or
condition. Check whether the USB memory operates normally in the vehicle before using it.
Take great care to ensure that the USB connection does not come in contact with the human body
or any object and the USB linking cable does not disturb a safe driving.
When you connect and disconnect the USB memory to the audio system several times in a short
periods, it may cause the USB memory to corrupt. If you particularly disconnect USB memory
during playback, it may be broken or operate incorrectly.
When you use the USB device for charging or heating by using the USB terminal on the audio
system, it may cause the system to deteriorate or fail.
iPod is a registered trademark of Apple Inc.
This audio system supports only the following iPod products: iPod Nano /iPod/iPod Touch/ iPhone.
This audio system may not support some iPod/iPhone products.
Always use the linking cable included with the iPod product when connecting it to the audio system.
The other cables may not be compatible and cause the audio system to fail.
In some cases, the iPod product may be damaged or not operate normally when the engine is
switched on while it is connected to the audio system. When not in use, always disconnect the iPod
product with the engine switched off.
When you use the iPod by connecting it to the audio system, the playback function and information
display may differ from original.
The iPod product can't be recharged using a iPod linking cable. -
-
-
-
-
-
-
-
-
-
-
-Cautions for using USB memory/iPod