odometer SSANGYONG KORANDO 2013 Service Manual

6) Odometer (ODO) and Trip Meter (TRIP)
The total driving distance (0 to 999,999 km or 0 to 999,999 miles) and the trip distance (0.0 to 999.9 km
or 0.0 to 9,999.9 miles) are calculated by using the value of pulse per 1 km which is programmed in the
EEPROM.
Applicable maximum driving speed is 300 km/h. If the vehicle speed goes over the limit, ODO and Trip
meter does not operate any more and the pointer indicates the maximum km/h (MPH). The pulse count
information is sent from the speed module according to the speed CAN data that matches the speed
frequency.

8010-01
Function Signal Remark
Input data Speed signal
Display type 4 digits LCD
Display range A: 0.0 ~ 999.9 km
(mile)
B: 0.0 ~ 9999.9 km
(mile)
Resolution 0.1 km (mile)
Maximum Odo
value
km
0.0 km
IGN OFF Memorize and maintain previous trip distance
Data clear Supply B+ voltage for the first time
Press and hold mode switch for more than 1 sec.
Maximum Odo
valueIf the signal indicating actual vehicle speed above 300 km/h is received, the data is
not accumulated.
Function Signal Remark
Input data Speed signal
Display type 6 digits LCD
Display range 0~999999 km(mile)
Hold
Resolution 1 km (mile)
Maximum Odo
valueIf the signal indicating
actual vehicle speed
above 300 km/h is
received, the data is
not accumulated.
STD Class Odometer Display & Data Storage
STD Class Tripmeter Display

Function Signal Remark
Display type 3 digits LCD
Display range 50 km ~ 999 km
(30 miles ~ 999 miles)
Resolution 1 km (mile)
Display interval every 1 seconds
(1) DTE (Distance To Empty) Mode
The DTE (distance to empty) function is an estimation on how much further the vehicle can be driven with
the fuel remaining in the tank, based on the previous driving pattern (fuel economy).
7) Display Mode
STD Class Odometer Display & Data Storage

8510-00
Windshield heating switch
Press this switch to operate the windshield
heating system for 12 minutes. Press the
switch again to stop the system. The
heated glass will operate for about 6
minutes when the switch is pressed again
within 10 minutes after completion of its
first operation cycle. The indicator lamp for
the switch comes on when the heating is
on.
Hazard warning flasher switch
When the driver presses the switch, all the
turn signal lamps flash regardless of the
ignition switch status. Pressing the switch
again turns off the turn signal lamps. The turn
signal lamp does not operate while the
hazard warning flasher operates.
TRIP/RESET switch
Whenever pressing this button, the information is
displayed in the following order: Odometer, Trip
A, Trip B, Distance to empty, Average fuel
economy, Instant fuel economy, Illumination level,
Tire pressure (with TPMS), Ambient air
temperature (for STD); Trip A, Trip B, Distance to
empty, Average fuel economy/Instant fuel
economy, Illumination level, Tire pressure (with
TPMS), Ambient air temperature (for SVC). Press
and hold this button to initialize (reset) Trip A/Trip
B and average fuel consumption, adjust
illumination level or change the unit of
temperature.
Description
Rear glass/outside rearview mirror heating
switch
Press this switch to operate the rear glass and
outside rearview mirror heating system for 12
minutes. Press the switch again to stop the
system. The heated glass will operate for about 6
minutes when the switch is pressed again within
10 minutes after completion of its first operation
cycle. The indicator lamp for the switch comes on
when the heating is on.
The switch is operable only when the engine
is started.
The hazard warning flasher blinks
during emergency hazard warning
lamp control and air bag deployment
signal activation.
The switch is operable only when the
engine is started.

SVC class instrument cluster
TRIP A TRIP BSTD class instrument cluster
TRIP A TRIP B
(3) Trip switch
Whenever pressing this button, the information is displayed in the following order: Odometer, Trip A, Trip
B, Distance to empty, Average fuel consumption, Instant fuel consumption, Illumination level, Ambient air
temperature (for STD); Trip A, Trip B, Distance to empty, Average fuel consumption, Instant fuel
consumption, Illumination level, Ambient air temperature (for SVC). Press and hold (for more than 1 sec)
this button to initialize (reset) Trip A/Trip B and average fuel consumption, adjust illumination level or
change the unit of temperature.
Description
The factory setting is DTE mode.
Display
Mode
SwitchDetecting
timeFunction
Briefly
and holdBelow 1
second
(60 to
980 ms)STD- Mode change
SVC- Mode change
Press
and holdOver 1
seconds- Reset
(Trip A, B, average fuel consumption)
- Change
Not
pressOver 3
seconds- Mode change