clutch SSANGYONG MUSSO 2003 Service Manual

5D2-52 TRANSFER CASE (TOD)
32. Install shift shaft oil seal if it is not installed.
33. Using pliers equipped with soft jaws, rotate the triangularshaft so it is aligned with the triangular slot in the transfer
case shift motor. If triangular shaft will not rotate, rotate the rear output shaft.
34. Slightly loosen the two nuts that attach the slotted support bracket to the end of the motor house.
35. Apply Black Non-Acid Cure Silicone Rubber or equivalent to motor housing base and install on transfer case.
36. Install the transfer case shift motor and three bolts along with speed sensor wire harness bracket and tighten. NoticeThe wire harness must be routed as shown to provide clearance and to prevent the wire harness from grounding
the damper.
37. Holding the slotted support bracket tight against the motor housing end, secure the bracket to the transfer case,
tightening the bolt with lockwasher to 8-11 Nm (72-96 lb-in).
38. Retighten the two nuts that attach the slotted support bracket to the end of the motor.
39. Install the clutch coil wire terminal and sensor wires.

9A-6 BODY WIRING SYSTEM Engine Room Fuse (EF) and Relay Box1 Fuse (15A) : ABS, ABD
2 Fuse (20A) : Sun Roof
3 Fuse (10A) : Air Bag
4 Fuse (15A) : Audio, Clock, Out Side Mirror
5 Fuse (30A) : Cigarette lighter, Power Socket
6 Fuse (30A) : Heater
7 Fuse (15A) : Door Lock
8 Fuse (30A) : Rear Heated
9 Fuse (10A) : Audio, Buzzer, Chime, Clock
10 Fuse (30A) : Power Window
11 Fuse (10A) : Immobilizer
12 Fuse (20A) : T/C
13 Fuse (15A) : Interior Lamp
14 Fuse (15A) : Hazard Lamp
15 Fuse (15A) : Stop Lamp
16 Fuse (15A) : Turn signal Lamp, Head Lamp
17 Fuse (10A) : Back up Lamp
18 Fuse (15A) : Cluster, STICS
19 Fuse (15A) : A/T, Diagnosis
20 Fuse (15A) : Over Voltage Protection Relay (Gasolin Only)
21 Fuse (15A) : Seat Heater
22 Fuse (15A) : ECS
23 Fuse (15A) : Front Wiper & Washer
24 Fuse (10A) : Rear Wiper & Washer, A/C
25 Relay : Front Wiper 26 Relay : ABS Warning Lamp
27 Relay : Flasher Unit
28 Relay : Fuel Pump (Gasoline Only)
29 Relay : Shift Lock (A/T)
30 Relay : Clutch Interlock & Neutral
31 Relay : Sun Roof
32 Relay : A/T ‘B’ Interlock (MB A/T)
33 Relay : Power Window
34 Relay : Rear Fog Lamp
35 Relay : ECS
36 Relay : Compressor (Diesel E/G)
Condenser Fan (Gasoline E/G)
37 Relay : Condenser Fan
38 Relay : Air Conditioner
39 Fuse (10A) : Tail Lamp
40 Fuse (15A) : Head Lamp(LH)
41 Fuse (15A) : Head Lamp(RH)
42 Fuse (15A) : Front Fog Lamp
43 Fuse (10A) : Horn
44 Fuse (10A) : Compressor
45 Relay : Resistor with Diode (Gasoline E/G)
46 Relay : Front fog Lamp
47 Relay : Condenser Fan
48 Relay : Tail Lamp
49 Relay : Horn

9A-8 BODY WIRING SYSTEM1 Fuse Box
2 Door Lock Relay
3 Relay Box
3.1 Front Wiper Relay
3.2 ABS Warning Lamp Relay ....................................ABD 5.0
3.3 Flasher Unit
3.4 Fuel Pump Relay ................................................. Gasoline E/G
3.5 Shift Lock Relay ................................................... Automatic Transmission
3.6 Clutch Interlock & Neutral Relay ...........................Manual Transmission or Automatic Transmission
3.7 Sun Roof Relay
3.8 Automatic T ransmission ‘B’ Switch Interlock ....... Automatic Transmission
3.9 Power Window Relay
3.10 Rear Fog Lamp Relay .......................................... Rear Fog Lamp
3.11 ECS Relay 4 Defogger Relay
5 Ground 1
6 Roof Wiring Connector
7 Diode 1
8 Front Door Wiring Connector
9 Front Door Wiring Connector
10 Front Door Wiring Connector 11 Front Door Wiring Connector
12 Kick Down Relay .................................................. Automatic Transmission
13 Floor Wiring Connector
14 Floor Wiring Connector
15 Floor Wiring Connector
16 ABD Floor Wiring Connector ................................ABD 5.0
17 ECS Floor Wiring Connector
18 Rear Iper & Washer Switch
19 Clutch Switch ........................................................ Manual Transmission
19-1 Clutch Switch ........................................................ E32 Gasoline E/G with Manual Transmission
20 Stop Lamp Switch
21 Outside Mirror Switch
22 Ignition Switch
23 Multi Function Switch
24 Multi Function Switch
25 Black Out Switch .................................................. Black Out Lamp
26 Black out switch ................................................... Black Out Lamp
27 Joint Connector (Tail)
28 Joint Connector (Ignition)
29 Cluster
30 Cluster ................................................................. Automatic Transmission
31 Cluster
32 Cluster
33 4WD Switch .......................................................... Except TOD
33-1 4WD Switch .......................................................... TOD
3 4 Hazard Switch
35 Ground 2
36 Pedal Module ....................................................... Gasoline E/G with MSE ECU
37 Audio Switch
3 8 Immobilizer ........................................................... Crypto Type, Gasoline E/G with MSE ECU or Diesel E/G
39 Ignition Switch
40 Multi Function Switch
4 1 STICS
4 2 STICS
4 3 REKES ................................................................. Remote Keyless

MUSSO-SPORTS 1A-3
SUPPLEMENT
HUBER EGR
SYSTEM DESCRIPTION The following chart shows the relationship between the input and the output in Huber EGR control unit. Compared to traditional system that only operates theEGR valve with RPM sensor and Micro switch, the HuberEGR control unit bring big differences that of traditionalsystem on the functions.
Input Signal
RPM sensor (CPS)
EGR valve lift sensor
Throttle position sensor (TPS) - M/T
Shift lever position
Throttle position sensor (TPS)
Vehicle speed sensor(VSS) Basic input signal for EGR operation Engine cold or hot signal
Position signal of EGR valve that is triggered by vacuum modulator 1 Transfer the engine load signal to the control unit directly (manual transmission)
TCU (A/T)
EGR
Control
Unit
Coolant temperature sensor (CTS)
Solenoid valve (Control forvacuum modulator 2)
If the control unit determines it is in no-load sharp accel- eration mode after analyzing the input signals, this conver- sion type switch reduces the fuel consumption by cutting off the intake air pressure from
fuel injection ALDA and gen- erating the vacuum pressure. In no-load sharp acceleration
mode, Duty Control ( continu- ous precise control) is acti- vated according to the varia- tions of the input signals when the solenoid valve generates the vacuum pressure in ALDA.
Vacuum modulator 2
The opening value of the modulator is precisely con- trolled by input signals and programmed MAP, and the opening value of EGR valve is also changed by the varia- tions of vacuum pressure to EGR valve. The changed opening value is transferred to the control unit as input signal.
Vacuum modulator 1
TCU in automatic transmission equipped vehicle transfers the information such as driving conditions and speeds into the EGR control unit. EGR control unit uses the shift lever position and vehicle speed as important information for operating the solenoid valve during no-load sharp acceleration mode. In manual transmission, the signal of vehicle speed is transferred into the EGR control unit directly.
Clutch switch
In manual transmission, the clutch switch is the one of core elements to determine driving condition. Output Signal
EGR Control Unit

1A-34 MUSSO-SPORTS
SUPPLEMENT
15 IGN1
31
* ( ) : A/T
* A/T TPS, RPM Signal : TCU A5
30
GND
F24
LW A/T
TCU A5 Clutch SW
"1" TPSM/T
41 2
2 RPM Sensor
S201
1 3
LW GrW HUBER EGR ECU (K2004) BG
C R G BrB BrWLRG
10A
BAT+
F17
RY RY 3 9 28 62 61 81 10 29
1
4 6 0798 05 675 4 324 3 332 3 736
WR W WB BrW GR
WR W WB BrW GR BG BrG GL LG YL LB
WR Lift Sensor
EGR Valve Water Sensor
Temp EGR Modulator Exhanst Gas
RecirculationModulator Sol Valve
W WB BrW GR BG BrG GL LG YL LB
S201
8
12 10A
213 7 8
B
13(11) 14(12) 11(9) 12(10) 9(7) (10)8
C901 (C902)
C901
C108
C105
C104
G204
Ef 2 Ef 8
80A60A
C103
2
56 7 2 1
16 15 1411 10
4. HUBER EGR CIRCUIT(MUSSO SPORT)

USAGE AND CAPACITY OF FUSES IN FUSE BOX 4-3
2. I/P FUSE BLOCK
1) POSITION OF RELAY AND FUSE 2) USAGE OF FUSE IN PASSENGER ROOM FUSE BOX
* 30 : BAT(+) Power Supply Through Ef1.
15A10A
10A15A10A
20A10A10A
10AST F110AIG1 F210AIG1 F3
ACC10AF4 B+30AF5
B+
(1) F6
F13
IG1
F20
15AF730AF1410AF21
F8F15F22
20AF915AF1610AF23
F10
B+
(2)
F17
F24
20AF1115AF1810A 15A
20AF1210AIG2 F19
30A
F25 F26
F27
85
87a3087
86
85
-3087
86
BE
L
85-
30
87
86
2) RELAY BOX
FRONT WIPERRELAY DEFOGGER
RELAY TURN SIGNAL
RELAY GSL : FUEL PUMP RELAYDSL : CIGAR LIGHTER, P/SOCKET RELAY A/T SHIFT LOCK
RELAY
8730
8685
8730
8685
8730
8685
8730
8685
A/T:PNP RELAY M/T:CLUTCH INTER LOCK RELAY SUNROOF
RELAY 'B' S/W
INTERLOCK RELAY POWER WINDER
RELAY 10A 10A10A10A30A15A15A10A20A20A20A20A30A15A15A10A 15A 10A10A10A10A10A10A10A15A30A
F1F2F3F4F5F6F7F8F9
F10 F11F12F14F15F16F17 F18 F19F20F21F22F23F24F25F26F27
Fuse No Capacity Usage
Starter Motor Relay Air BagABS/ABDOutside Mirror, AudioCigar Lighter, Power SocketStop LampHazard SwitchInteriorFuel Pump (Only GSL)TCCU/TOD, Power seatOVPR 1 (Only GSL)OVPR 4 (Only GSL)Heated GlassSun RoofRear Fog Lamp, Power ANT., ECSDLCFront Wiper & WasherRear Wiper & WasherTCCU/TCMBack Up Lamp, Turn Signal LampHead Lamp, Cluster OVPR 3 (Only GSL) Speed Sensor, Unit, Relay CoilNot UsedNot UsedNot Used
Power Supply
30 BAT(+)
ACC (15C) IGN2 (15A)
30 BAT (+)
IGN1 (15)
IGN1 (15)
SPARE
8730
8685
8730
8685
ECS
RELAY ABS WARNING
LAMP RELAY
8730
8685

3) PEDAL MODULE, THROTTLE MOTOR & SENSOR, CTS, SENSOR(KNOCK, INTAKE AIR TEMP',HEATED O 2) CIRCUIT ...................................................................................................................... ......................5-28
(1) W/O EURO III ............................................................................................................... ..................................................................... 5-28
(2) W/ EURO III ................................................................................................................ ....................................................................... 5-30
4) VSS, CLUTCH SWITCH, IMMOBILIZER CIRCUIT ...................................................................................... .........5-32
(1) W/O EURO III ............................................................................................................... ..................................................................... 5-32
(2) W/ EURO III ................................................................................................................ ....................................................................... 5-34
5. ECM (E32, MSE) ............................................................................................................... .......... 5-36
1) OVPR, FUEL PUMP, CCP SOLENOID CIRCUIT ........................................................................................ ....... 5-36
(1) W/O EURO III ............................................................................................................... ..................................................................... 5-36
(2) W/ EURO III ................................................................................................................ ....................................................................... 5-38
2) IGNITION COIL, SENSOR (CAM SHAFT POSITION, HFM, CKP), CAM SHAFT ACTUATOR, RESONANCE FLAP CIRCUIT ............................................................................................................................... . 5-40
3) PEDAL MODULE, THROTTLE MOTOR & SENSOR, SENSOR(KNOCK, ECT, HEATED O 2) CIRCUIT ....... 5-42
(1) W/O EURO III ............................................................................................................... ..................................................................... 5-42
(2) W/ EURO III ................................................................................................................ ....................................................................... 5-44
4) VSS, CLUTCH SWITCH, IMMOBILIZER CIRCUIT ...................................................................................... ....... 5-46
5) HEATED O 2 SENSOR(1,2,3,4) ............................................................................................................... ............... 5-48
6. ECM (E20, HFM).............................................................................................................. ........... 5-50
1) INJECTOR, OVPR, IGNITION COIL, FUEL PUMP CIRCUIT ............................................................................ 5-50
2) CCP SOLENOID, SENSOR (MAF, CKP) CIRCUIT ...................................................................................... ...... 5-52
3) THROTTLE MOTOR & SENSOR, ECT SENSOR, VSS, HEATED O 2 SENSOR CIRCUIT ............................ 5-54
7. ECM(E23, HFM) ............................................................................................................... ........... 5-56
1) INJECTOR, OVPR, IGNITION COIL, FUEL PUMP CIRCUIT(W/ IMMOBILIZER) ........................................... 5-56
2) INJECTOR, OVPR, IGNITION COIL, FUEL PUMP CIRCUIT(W/O IMMOBILIZER) ........................................ 5-58
3) SENSOR (CKP, CMP, KNOCK, MAF), CAM SHAFT ACTUATOR CIRCUIT ...................................................... 5-60
4) THROTTLE MOTOR & SENSOR, ECT SENSOR, VSS, HEATED O 2, SENSOR CIRCUIT ............................. 5-62

8. ECM(E32, HFM) .......................................................................................................................... 5-64
1) INJECTOR, OVPR, IGNITION COIL, FUEL PUMP CIRCUIT(W/ IMMOBILIZER) ........................................... 5-64
2) INJECTOR, OVPR, IGNITION COIL, FUEL PUMP CIRCUIT(W/O IMMOBILIZER) ........................................ 5-66
3) SENSOR (CKP, CMP, KNOCK, MAF), CCP SOLENOID, CAM SHAFT ACTUATOR CIRCUIT ....................... 5-68
4) THROTTLE MOTOR & SENSOR, SENSOR (IAT, ECT, HEATED O 2), VSS, CIRCUIT (UNLEAD) ................. 5-70
5) THROTTLE MOTOR & SENSOR, SENSOR (IAT, ECT), CO POTENTIO METER, VSS CIRCUIT(LEAD) ..... 5-72
9. DLC CIRCUIT ................................................................................................................. ............. 5-74
10. TCM(GSL, BTRE) .............................................................................................................. ......... 5-76
1) POWER SUPPLY, GROUND, INDICATION LAMP CIRCUIT ............................................................................. 5- 76
2) KICK DOWN SWITCH, SELECT LEVER POSITION SENSOR, TRANSMISSION CIRCUIT ........................ 5-78
11. TCM(DSL, BTRE) .............................................................................................................. ......... 5-80
1) POWER SUPPLY, GROUND, INDICATION LAMP, SENSOR (TR, ENGINE SPEED) CIRCUIT .................... 5-80
2) KICK DOWN SWITCH, SELECT LEVER POSITION SENSOR, TRANSMISSION CIRCUIT ........................ 5-82
12. KICK DOWN RELAY, 'B' SWITCH CIRCUIT (MB A/T) ........................................................... 5-84
13. TCCU-PART TIME .............................................................................................................. ........ 5-86
1) POWER SUPPLY, GROUND, INDICATION LAMP, PNP RELAY, CLUTCH SWITCH CIRCUIT ..................... 5-86
2) 4WD SWITCH, T/C SPEED SENSOR, T/C MOTOR CIRCUIT ........................................................................ 5-88
14. TCCU-FULL TIME .............................................................................................................. ........ 5-90
1) POWER SUPPLY, GROUND, INDICATION LAMP, NEUTRAL RELAY, CLUTCH CIRCUIT ............................ 5-90
2) 4WD SWITCH, T/C SPEED SENSOR, T/C MOTOR CIRCUIT ........................................................................ 5-92
15. TOD(TORQUE ON DEMAND)-E32,MSE .................................................................................. 5-94 1) POWER SUPPLY, GROUND, WARNING LAMP, 4WD SWITCH, T/C MOTOR CIRCUIT .............................. 5-94
2) T/C SPEED SENSOR, PNP RELAY, CLUTCH SWITCH, CAN CIRCUIT .......................................................... 5-96
16. ECS ......................................................................................................................... ..................... 5-98
1) POWER SUPPLY, GROUND, SENSOR(WHEEL'G, VERTICAL, LATERAL) CIRCUIT ................................... 5-98
2) ECS SWITCH, DAMPER CIRCUIT ...................................................................................................................... 5-100

5-8 ELECTRICAL WIRING DIAGRAMS
1. STARTING & CHARGING SYSTEM
1) GSL E23 MB A/TC101 (21Pin, Colorless) C102 (2Pin, Colorless) C108 (2Pin, Black) C110 (6Pin, Black) C208B (15Pin, Black)
b. CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION
a. CONNECTOR INFORMATION
C108
W/H GENERA- TOR C208B
W/H MAIN
C101
W/H MAIN C102
W/H MAIN C110
W/H MAIN
START LOCK
SWITCH (MB A/T) IGNITION SWITCH
CLUSTER
CONNECTOR(NUMBER)CONNECTING. WIRING HARNESS
Main - Engine Main - Engine Genertor - Engine Main - Engine MainMain - T/M
CONNECTOR POSITION
Inside The Engine Room Fuse Block Inside The Engine Room Fuse Block Under The Air Cleaner Housing (GSL)Behind The ABS Module (HFM) Upper The T/C (GSL)
12345 678910
11 12 13 14 15 16 17 18 19 20 211212
135 2 46
1
4 52
8
14
7
93
15
13
10
11 6
12
76
12
4
38 N
P IGNR
D
3910123 456
11 2
29 38
28
13 2021
39 434842
M
+-30 (BAT +)
: M/T (HFM E20, E23)
15 (IGN 1) 15A (IGN 2)
15C (ACC)
31 GND
Cluster (Charging
WarningLamp)
G105
G104
B B
G201
BST 3
4
OFF
"12"ICU
ACC
ONST BL
BY BY BY
BL
BG
BG 162
F22
10A
F24
10A
RG
W
RGLB 18 5
2 1 YW YW YW
C108
Generator
I.C Regulator D+
B+ 1
C101
Resister 15
C101
14
Ef7
40A
E
f2 80A
BW L LW
Ignition Switch
C102
1
Battery Start LockSwitch(MB A/T)
BY StarterMotor
1
30 87
8685
2
Clutch Switch
1 2
C110
4 C208B
PNP
Relay
8
C208B
2

5-10 ELECTRICAL WIRING DIAGRAMSMain - Engine Main - Engine Genertor - Engine Main - T/MMain - T/M Main
2) GSL BTRE A/T, GSL E32 MB A/T
C101 (21Pin, Colorless) C102 (2Pin, Colorless) C108 (2Pin, Black) C207 (16Pin, Black) C208 (16Pin, Black) G201
b. CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION
a. CONNECTOR INFORMATION
C108
W/H GENERA- TOR C208
W/H T/M
C101
W/H MAIN C102
W/H MAIN C207
W/H T/M
START LOCK
SWITCH (MB A/T) IGNITION
SWITCH
CLUSTER
CONNECTOR(NUMBER)CONNECTING. WIRING HARNESSCONNECTOR POSITION
Inside The Engine Room Fuse Block Inside The Engine Room Fuse Block Under The Air Cleaner Housing (GSL)Upper The T/C Upper The T/C Right The I/P Fuse Block
12345 678910
11 12 13 14 15 16 17 18 19 20 211212
1234 5678
9 101112
13 14 15 16
76
12
4
38 N
P IGNR
D
3910123 456
11 2
29 38
28
13 2021
39 434842PNP SWITCH
12
34
CLUTCH SWITCH
12
M
30 (BAT +) 15 (IGN 1)15A (IGN 2)
15C (ACC)
31 GND
Cluster (Charging
WarningLamp)
G201
G201
G105 B BST3
4
OFF
ACC
ONST BL
R M/T
162
F22
10A
F24
10A
RG
W
RG
+-
LB 18 5
2 1 YW YW YW
C108
Generator
I.C Regulator D+
B+ 1
C101
Resister 15
C101
14
E f7
40A
F110A
E
f2 80A
BW L LW
Ignition Switch
C102
1
C207
Battery
PNP Switch(BTRE A/T) Start Lock
Switch (MB A/T)
BG BL BY
BY
BY BY
StarterMotor BG BG
1 3
12
12
4
C101
A/T
M/T 20C101
13
C208
3
C207
3 C208
4
87
Clutch
Switch 85
Starter Motor
Relay
30 86
G104
1234 5678
9 101112
13 14 15 16