manual transmission SSANGYONG MUSSO 2003 Service Manual

0B-2 GENERAL INFORMATION661LA
4Cylinder
DIESEL 89
92.4
2299 22:1
101/4000
21.5/2400
Application
Engine Type Bore (mm) Stroke (mm)
Total Displacement (cc) Compression Ratio Maximum Power (ps/rpm)
Maximum Torque (kg.m/rpm)
Engine
662NA
5Cylinder
DIESEL 89
92.4
2874 22:1
95/4000
19.6/2400662LA
5Cylinder
DIESEL 89
92.4
2874 22:1
120/4000
25.5/24002.0L DOCH 4Cylinder
GASOLINE 89.9 78.7
19989.6:1
135/5500
19.3/40002.3L DOCH 4Cylinder
GASOLINE 90.9 88.4
2295
10.4:1
149/5500
22.4/40003.2L DOCH 6Cylinder
GASOLINE 89.9
84
3199 10:1
222/5500
31.6/3750
661LA
TREMEC
T5
3.969 2.341 1.457 1.0000.8513.705 4.55
3.4
Application
Ignition Type
Ignition Timing (BOTH)Ignition Sequence Spark Plug Gap (mm) Spark Plug Maker
Spark Plug Type Ignition System
Clutch - Manual Type 2.0L DOHC
6° ± 2°
1-3-4-2
0.8 ± 0.1
2.3L DOHC
6° ± 2°
1-3-4-2
0.8 ± 0.1 2.0L DOHC
8° ± 2°
1-5-3-6-2-4 0.8 ± 0.1
Distributorless Ignition Bosch, Chapion, Beru
F8DC4(BOSCH)
C11YCC(CHAMPION) 14F8DU4(BERU)
661LA 225 1509.2
662NA
225 1509.2 662LA
2401509.2 2.0L DOHC
2251509.2 2.3L DOHC
2251509.2 3.2L DOHC
2401559.3
Application
TypeOutside Diameter (mm) Inside Diameter (mm) ThicknessFluid
Single Dry Diaphram
Common use :Brake Fluid
Application
Maker
Type or Model
Gear Ratio : 1st 2nd3rd 4th 5thReverse
Final Drive RatioOil Capacity (L)
Manual Transmission
662NA
TREMEC
T5
3.969 2.341 1.457 1.0000.8513.705 4.55
3.4 662LA
TREMEC T5
3.9692.341 1.457 1.0000.8513.705 4.27
3.4 2.0L DOHC
TREMEC T5
3.9692.341 1.457 1.0000.8513.705 4.55
3.4 2.3L DOHC
TREMEC
T5
3.9692.341 1.457 1.0000.8513.705 4.55
3.4 3.2L DOHC
TREMEC T5
3.9692.341 1.457 1.0000.8513.705 3.73
3.4

GENERAL INFORMATION 0B-9
Chassis and Body
Months
MAINTENANCE ITEM MAINTENANCE INTERVAL
Kilometers or time in months, whichever comes first
120
105
90
75
60
45
30
15
1
96
84
72
60
48
36
24
12
-
x1,000 km
Exhaust pipes & mountings Brake/Clutch fluid
(3)(4)
Parking brake/Brake pads F & R (5)Brake line & connections (including booster)
Manual transmission oil (3) Clutch & brake pedal free play
Front & Rear Differential Fluid (3)I
R
IIIII- --II
-
I IIIIII I
I
R I II I I IIII
R I
R IIIII I II
R
II
R I
R IIIIII II
R I IIII
Automatic transmission fluid (MB W4A040) (6) Automatic transmission fluid (BTRA M74)Chassis & underbody bolts & nuts tight/secure Tire condition & inflation pressure
Wheel alignment (7) Steering wheel & linkage
Power steering fluid & lines* (3)Drive shaft boots Seat belts, buckles & anchors Lubricate locks, hinges & bonnet latchIIII I I IIII I III I I IIII I IIII
R
III I IIII IIII I IIIIIIIII I III I
R R
III I IIII IIII I IIII
Transfer case fluidRII
I
Inspect & ADJUST when abnormal condition is noted
I
I II I IIII
Chart Symbols :
I - Inspect these items and their related parts. If necessary, correct, clean, replenish, adjust or replace.R - Replace or change.
(3) Refer to “Recommended fluids and lubricants”.
(4) Change the brake / clutch fluid every 15,000 km if the vehicle is mainly driven under severe conditions:- Driving in hilly or mountainous terrain, or
- Towing a trailer frequently
(5) More frequent maintenance is required if under severe condition : short distance driving, extensive idling, frequent low - speed operation in stop-and-go traffic or driving in dusty condition.
(6) Change automatic transaxle fluid and filter every 75,000 km if the vehicle is mainly driven under severe conditions. - In heavy city traffic where the outside temperature regularly reaches 32°C (90°F) or higher, or- In hilly or mountainous terrain, or- When doing frequent trailer towing, or- Uses such as found in taxi, police or delivery service.
(7) If necessary, rotate and balance wheels.

GENERAL INFORMATION 0B-11
Chassis and Body
Months -
MAINTENANCE ITEMMAINTENANCE INTERVAL
Kilometers or time in months, whichever comes first
100
90
80
70
60
50
40
30
20
10
1
60
54
48
42
36
30
24
18
12
6
x1,000 km
Exhaust pipes & mountings
Brake/clutch fluid (3) (4)
Parking brake/Brake pads (F & R) (5) Brake line & connections (including booster)
Manual transmission fluid (3)Clutch & brake pedal free play
F & R Differential fluid (3)
I I I IIIIIIIIIIIII I
R
IIIII IIIIIII IIII
R I
R I
R
IIIII IIIIIIIIIIIIII I
R
IIIII IIII
R I
R
Automatic transmission fluid (BTRA M74) (6) Chassis & underbody bolts & nuts tight/secure Tire condition & inflation pressure
Wheel alignment (7) Steering wheel & linkage
Power steering fluid & lines* (3) Drive shaft boots Seat belts, buckles & anchors Lubricate locks, hinges & bonnet latchI II I IIII III I IIII IIII I III I
I II I IIII III I IIIIIII I IIII III II II III I IIIIIII I IIII
Transfer case fluid (3)
RI R
I
I
I
I I I II IIII I IIII
Inspect & ADJUST when abnormal condition is noted
II I
Chart Symbols :
I - Inspect these items and their related parts. If necessary, correct, clean, replenish, adjust or replace.R - Replace or change.
(3) Refer to “Recommended fluids and lubricants”.
(4) Change the brake / clutch fluid more regularly if the vehicle is mainly driven under severe conditions :- Driving in hilly or mountainous terrain, or
- Towing a trailer frequently
(5) More frequent maintenance is required if under severe condition : short distance driving, extensive idling, frequent low - speed operation in stop-and-go traffic or driving in dusty condition.
(6) Change automatic transmission fluid every 70,000 km if the vehicle is mainly driven under severe conditions. - In heavy city traffic where the outside temperature regularly reaches 32°C (90°F) or higher, or- In hilly or mountainous terrain, or- When doing frequent trailer towing, or- Uses such as found in taxi, police or delivery service.
(7) If necessary, rotate and balance wheels.

M162 ENGINE MECHANICAL 1B1-53
FLYWHEEL / DRIVEN PLATE Preceding Work : Removal of manual or automatic transmission
1 Flywheel Mounting Bolt (M10 x 22, 8 pieces)............................................... 1st step 45+5 Nm
2nd step +90 ° +10 °
2 Plate 3 Driven Plate (A/T)
4 Dowel Pin
Service Data Standard (Stretch Bolt)
Nominal Size
Stretch Side Diameter
Bolt Length
Tightening Torque
M x 1.5
8.5 - 0.2 mm 8.0 mm
21.8 - 22.2 mm-
When New
Min. Diameter When NewDd L
1st step 50 Nm, 2nd step 90 °

1B1-54 M162 ENGINE MECHANICAL Removal & Installation Procedure
1. Unscrew the stretch bolt.Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Crankshaft Front Seal
4 Flywheel MTG Bolt
5 Crankshaft
6 Dowel Pin
7 Plate
8 TGCC
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear

Replace the bolt when the stretch side diameter (d) of the flywheel mounting bolt is less than 8.0mm.
For the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90 ° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles, or the driven plate (3), and plate (2) for Auto. transmission vehicle.
3. Installation should follow the removal procedure in the reverse order. Tightening Torque
1st step 45+5 Nm
2nd step 90
° + 10 °

1B2-60 M161 ENGINE MECHANICAL
FLYWHEEL/DRIVEN PLATE Preceding Work : Removal of manual or automatic transmission
1 Flywheel Mounting Bolt(M10 x 22, 8 pieces) ................ 1st Step 45 Nm 2nd Step 90°+10 °
2 Plate 3 Driven Plate (A/T)
4 Dowel Pin
5 Flywheel (M/T)
Service Data Standard (Stretch Bolt)
Nominal Size
Stretch Side Diameter
Bolt Length
Tightening Torque
M x 1.5
8.5 - 0.2 mm 8.0 mm
21.8 - 22.2 mm-
When New
Min. Diameter When NewDd L
1st step 50 Nm, 2nd step 90 °

M161 ENGINE MECHANICAL 1B2-61
Removal & Installation Procedure
1. Unscrew the stretch bolt.Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Radial Seal
4 Bolt
5 Crankshaft
6 Dowel Pin
7 Washer (Thickness : 3.5 mm)
8 Washer
9 Bolt
10 Front Drive Plate 11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear

Replace the bolt when the stretch side diameter (d) of
the flywheel mounting bolt is less than 8.0mm.
For the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90 ° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles, or the driven plate (3), and plate (2) for Auto. transmission vehicle.
3. Installation should follow the removal procedure in the reverse order. Tightening Torque
1st step 45 Nm
2nd step 90
°+5 °

1B3-82 OM600 ENGINE MECHANICAL
CRANKSHAFT BALL BEARING
1 Spacer
2 Cover ......................................... Replace
Notice
Manual transmission only.
Tools Required 000 589 33 33 00 Counter Support000 589 25 33 00 Internal Extractor Removal & Installation Procedure
1. Remove the manual transmission.
2. Using a puller, pull out the locking ring and ball bearing together.
Counter Support 000 589 33 33 00
Internal Extractor 000 589 25 33 00
3. Apply Loctite 241 on the new ball bearing and then insert the ball bearing to be stopped at the spacer ring by using a proper mandrel.3 Ball Bearing
4 Bolt ....................................... 45Nm + 90 °

1B3-94 OM600 ENGINE MECHANICAL
Manual transmission flywheel
Automatic transmission flywheel
OM661LA
OM662LA

OM600 ENGINE MECHANICAL 1B3-95
3. Remove the flywheel (3), if equipped with manualtransmission. Installation Notice Correctly align the position of dowel pin (2).
Tools Required 602 589 00 40 00 Engine Lock Removal & Installation Procedure
1. Install the engine lock.
Engine Lock 602 589 02 40 00
2. Remove the 12-sided stretch bolts (4). Installation Notice
Tightening Torque 45 Nm + 90 °
Notice If the length ‘L’ of bolts exceeds 22.5mm, replace the bolts.