turn signal SSANGYONG NEW REXTON 2012 Service Manual

Font Side
7910-01 Radiator Grille
- Changed the mounting type
(from on hood to on bumper).
- Changed the radiator grill design.
8310-01 Head Lamp
- Changed the head lamp design and functions.
- Turn signal lamp integrated with front fog lamp
1. EXTERIOR
7871-01 Front Bumper and Front PAS Sensor
- Changed the front bumper design according to the design changes of front combination lamp
and radiator grille.
- Changed the location of front PAS sensor.
Head lamp -
Low beam
Turn signal/Position lamp
Head lamp -
High beam Head lamp -
High beamHead lamp - Low beam
Position lamp (LED)
Front fog lamp
Front PAS sensorTurn signal/Front fog lamp
Front PAS sensor

0000-00
8310-23 Front
Combination
Lamp
- Front fog lamp and turn
signal lamp have been
integrated in combination
lamp assembyl.
7850-11 Outside Rearview Mirror
- Introduced the turn signal lamp on outside rearview mirror.
7810-04 Windshield Wiper Blade
- Changed the aero-blade material (from steel to rubber).
Outside turn signal lamp
6110-01 Hood Panel
- Changed the hood panel design.Front fog
lamp
Front fog
lamp
Turn signal lamp

0000-00
7940-02 Spoiler
- Added the wing type rear spoiler.
7880-13 Reflex Reflector
- Changed the reflex reflector according to
the changes of rear bumper.7940-34 Tailgate Lower Garnish
- Changed the tailgate lower garnish design.
Tail/Stop lampStop lamp
Turn signal lamp
Back-up
lamp
Tail lamp
Tail lamp
Turn signal
lamp
Back-up
lamp
Stop
lamp
8320-01 Rear Combination Lamp
- Changed the rear combination lamp design and functions.
- Changed the stop lamp and tail lamp to LED type.

D20DT Engine Remarks
HFM 6.0 HFM 6-ID
(Added digital signal function) -
Electrically controlled E-EGR valveECU controls the EGR valve directly.
It provides precise EGR control by
transmitting the electric signal of EGR
valve operating position. *
Vacuum modulator
Vacuum modulator for
turbocharger control
The vacuum modulator for controlling
EGR valve has been deleted. *
Throttle body is used to prevent the
engine from turning off with fluttering
noise at the moment the air to intake
manifold is blocked by closed flap
when the engine is switched off. *
Throttle body

HFM Sensor (ver. 6.0)VGT Turbo Chargera
Uncompressed air
Air coeaner Turbo
charger
Temperature
sensor
Pretension
graph
Ambient air
Air cleaner
Compressed air
1. INTAKE SYSTEM LAYOUT
The intake system is equipped with an electric throttle body which includes a flap. This flap is controlled
by an electrical signal to cut off the intake air entering to the engine when the ignition switch is turned off.
And, the improved HFM sensor has been adopted to control the intake air volume more precisely.
Exhaust manifold
Air coeaner
Intercooler Exhaust gas
VGT control actuator

Do not move the shift lever to Neutral position while driving with the cruise control turned on.
Otherwise, it may result in system malfunction or accidents.
Always be prepared to use the brake or accelerator pedal for safe driving while the cruise control
system is running.
The actual speed can be different from the set speed momentarily when driving on a uphill or
downhill. So, it is recommended to disable the cruise control function on a uphill or downhill. hen
driving on a steep hill use the engine brake and foot brake properly to protect the vehicle system
and for a safe driving.
Ensure that the safe distance is maintained and use the brake pedal if needed. 1.
2.
3.
4.
(1) Abnormal Cancellation of the Cruise Control
When the rapid deceleration is applied without braking.
When the rapid acceleration is applied without acceleration pedal intervention.
When the cruise control lever is faulty.
When the brake switch and the brake light switch input signal are implausible. 1.
2.
3.
When the cruise control function is cancelled abnormally or intermittent problems occur, stop the vehicle
and turn off the ignition switch and remove the key to reset the system. After a while, turn on the ignition
switch again to operate the cruise control system.

2) Fuel System Flow Diagram
The fuel from the fuel tank is supplied to the fuel heater of fuel filter/priming pump and then low pressure
generated by the low pressure pump (built into HP pump) is transmitted to the HP pump.
The fuel pressure at the HP pump is controlled by the IMV valve, and the maximum allowed pressure is
1,800 bar. The compressed fuel at the fuel pump is delivered to the rail, and injected by the injectors
according to the injection signals. The injection method is the same with the conventional method; Fuel
return by backleak which operates the needle valve.
The major difference is that the fuel return line is connected to the fuel filter inlet port, not the HP pump
venturi.
The pressure from the high pressure pump is increased to 1,800 bar from 1,600 bar, and the pump is now
installed to the cylinder head (cylinder block for previous model). The fuel pressure is generated by the
operation of intake camshaft and gears. The specifications for the IMV valve and the fuel temperature
sensor are not changed.

1. OVERVIEW
The intake system for D20DTR engine is equipped with a throttle body which includes a flap. This flap is
controlled by an electrical signal to cut off the intake air entering to the engine when the ignition switch is
turned off. Because of this, the shape of the intake manifold has been changed and improved HFM
sensor is newly adopted to control the intake air volume more precisely.
2. COMPONENT
2330-01 Intercooler assembly
2313-15 HFM sensor
HFM sensor, version 6
*For more information, refer to Chapter "Engine
Control".
2313-01 Air cleaner assembly

1543-00
1. SYSTEM DESCRIPTION
1) Overview
The lubrication system supplies oil to each lubrication section to prevent friction and wear and to remove
heat from the friction part. As the engine runs, frictional heat is generated on each lubrication section. If
this condition persists, the bearing can be burned and stuck.
In other words, it creates an oil film on each sliding surface to convert solid friction to liquid friction in order
to minimize wear and prevent temperature increasing on the friction part.
For the D20DTF engine with no oil pressure switch, the engine ECU receives the low engine oil level
signal from the oil level sensor and communicates with the instrument cluster through the CAN
communication to turn on the warning lamp.
2) Components
Oil coolerOil dipstick gaugeOil pump
Oil filter moduleOil pressure switchOil pan

Do not move the shift lever to Neutral position while driving with the cruise control turned on.
Otherwise, it may result in system malfunction or accidents.
Always be prepared to use the brake or accelerator pedal for safe driving while the cruise control
system is running.
The actual speed can be different from the set speed momentarily when driving on a uphill or
downhill. So, it is recommended to disable the cruise control function on a uphill or downhill. hen
driving on a steep hill use the engine brake and foot brake properly to protect the vehicle system
and for a safe driving.
Ensure that the safe distance is maintained and use the brake pedal if needed. 1.
2.
3.
4.
(1) Abnormal Cancellation of the Cruise Control
When the rapid deceleration is applied without braking.
When the rapid acceleration is applied without acceleration pedal intervention.
When the cruise control lever is faulty.
When the brake switch and the brake light switch input signal are implausible. 1.
2.
3.
When the cruise control function is cancelled abnormally or intermittent problems occur, stop the vehicle
and turn off the ignition switch and remove the key to reset the system. After a while, turn on the ignition
switch again to operate the cruise control system.