engine SSANGYONG RODIUS 2006 User Guide

01-6
RODIUS 2007.07
0000-00
ENGINE INFORMATION
2) SIDE VIEW
NO. FUNCTION NO. FUNCTION
23 Camshaft adjuster 27 Oil pump drive chain
24 Cooling fan and viscous clutch 28 Oil return pipe
25 Piston 29 Timing chain
26 Flywheel of drive plate

01-7
ENGINE INFORMATION
RODIUS 2007.07
0000-00
2. DESCRIPTION AND OPERATION
1) Cleanliness And Care
An automobile engine is a combination of many machined, honed, polished and lapped
surfaces with tolerances that are measured in the ten-thousanths of an inch. When any internal
engine parts are serviced, care and cleanliness are important. A liberal coating of enigne oil
should be applied to friction areas during assembly, to protect and lubricate the surfaces on
initial operation.
Proper cleaning and protection of machined surfaces and friction areas is part of the repai
r
procedure. This is considered standard shop practice even if not specifically stated.
Whenever valve train components are removed for service, they should be kept in order.
They should be installed in the same locations, and with the same mating surfaces, as when
they were removed. Battery cables should be disconnected before any major work is performed
on the engine. Failure to disconnect cables may result in damage to wire harness or othe
r
electrical parts.
2) On-Engine Service
Disconnect the negative battery cable before removing or installing any electrical unit, or
when a tool or equipment could easily come in contact with exposed electrical terminals.
Disconnecting this cable will help prevent personal injury and damage to the vehicle.
The ignition must also be in LOCK unless otherwise noted.
Notice Any time the air cleaner is removed, the intake opening -
Any time the air cleaner is removed, the intake opening should be covered. This will
protect against accidental entrance of foreign material, which could follow the intake
passage into the cylinder and cause extensive damage when the engine is started.g -

02-3
ENGINE ASSEMBLY
RODIUS 2007.07
0000-00
1113-01ENGINE ASSEMBLY
1. SPECIFICATIONS
1) ENGINE SPECIFICATIONS

02-4
RODIUS 2007.07
0000-00
ENGINE ASSEMBLY
2) PERFORMANCE CURVE

02-5
ENGINE ASSEMBLY
RODIUS 2007.07
0000-00
2. SPECIAL TOOLS AND EQUIPMENT

02-6
RODIUS 2007.07
0000-00
ENGINE ASSEMBLY

02-7
ENGINE ASSEMBLY
RODIUS 2007.07
0000-00
Name and Part Number
A9917 0012B (DW110-120)Holding Pin

02-8
RODIUS 2007.07
0000-00
ENGINE ASSEMBLY
3. FASTENER TIGHTENING SPECIFICATIONS

02-9
ENGINE ASSEMBLY
RODIUS 2007.07
0000-00
4. FASTENER TIGHTENING SPECIFICATIONS (CONT′D)

03-3
ENGINE FUEL SYSTEM
RODIUS 2007.07
0000-00
2211-22ENGINE FUEL SYSTEM
1. FUEL SYSTEM SPECIFICATION
Use Only Unleaded Fuel Rated at 89 Octane or Higher ▶
Fuel quality and additives contained in fuel have a significant effect on power output, drivability,
and life of theengine. Fuel with too low an octane number can cause engine knock.
- Use of fuel with an octane number lower than 89 may damage engine and exhaust system.
- To prevent accidental use of leaded fuel, the nozzles for leaded fuel are larger, and will not
fit the fuel filler neck of your vehicle.
Do Not Use Methanol ▶
Fuels containing methanol (wood alcohol) should not be used in vehicle.
This type of fuel can reduce vehicle performance and damage components of the fuel system.
- Use of methanol may damage the fuel sys-tem.
Vehicle Fueling from Drums or Storage Containers ▶
For safety reasons (particularly when using noncommercial fueling systems) fuel containers,
pumps and hoses must be properly earthed. Static electricity build up can occur under certain
atmospheric and fuel flow conditions if unearthed hoses, particularly plastic, are fitted to the
fuel-dispensing pump.
It is therefore recommended that earthed pumps with integrally earthed hoses be used, and
that storage containers be properly earthed during all noncommercial fueling operations.