relay SSANGYONG RODIUS 2007 User Guide

01-4
RODIUS 2006.09
0000-00
FUSE AND RELAY
Fuse and Relay in Instrument Panel
▶
The fuse box is underneath the dash board on the driver's side. You can find the function,
location and capacity for fuses from the back plate of the fuse box cover. If any electrical device
doesn't operate, check for an open fuse. If any fuse is blown, replace it with a new fuse.
If a new fuse also opens, have the electrical system checked and repaired by Ssangyong
Dealer or Ssangyong Authorized Service Operation.

01-5
FUSE AND RELAY
RODIUS 2006.09
0000-00
3. CAPACITY AND DESIGNATION
1) Engine Compartment

01-6
RODIUS 2006.09
0000-00
FUSE AND RELAY
2) Interior (Driver Side)

01-7
FUSE AND RELAY
RODIUS 2006.09
0000-00
1) D27DT - I
4. CIRCUIT DIAGRAM FOR FUSES AND RELAYS

01-8
RODIUS 2006.09
0000-00
FUSE AND RELAY
2) D27DT - II

01-9
FUSE AND RELAY
RODIUS 2006.09
0000-00
3) GASOLINE - I

01-10
RODIUS 2006.09
0000-00
FUSE AND RELAY
4) GASOLINE - II

0-5
STICS
RODIUS 2006.09
8710-01
The STICS in this vehicle has similar functions with the one used in the new Rexton. Additional
function of diagnosing through SCAN-Tool has been added into new STICS.
The major difference in hardware-wise is that STICS receives vehicle collision signal from G-
sensor in the airbag module to activate automatic door unlock function when the vehicle
collided over 15 km/h of vehicle speed.
1. COMPONENTS LOCATOR
STICS / ICM module
Air bag ECU
Sends the vehicle collision
signals to STICS.
Theft deterrent horn
Installed under the battery. This
horn works only for the theft
deterrent function, panic
function, and remote starting.
SCAN-tool
SCAN-100 is used fo
r
REKES key coding and
trouble diagnosis.
REKES
Added the escort and
panic function
RK STICS
ICM module
This module contains
various relays, chime and
buzzer controlled by
STICS

0-7
STICS
RODIUS 2006.09
8710-01
3. FUNCTIONS OF RK STICS
1) Wiper Control
(1) Wiper MIST and Washer Coupled Wiper
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch for
0.2 ~ 0.59 seconds (T2) with the ignition key “ON”, and it is turned off when the
parking terminal is turned off. 1.
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch
over 0.6 seconds (T2) with the ignition key “ON”, and it is turned on three times
immediately after turning off the washer switch. 2.

0-10
RODIUS 2006.09
8710-01
STICS
Rain sensing operation point ▶
The wiper relay is turned on and the wiper motor runs one cycle when the ignition key is
turned to “ON” position (while the wiper switch is in “AUTO” position).
The wiper relay (LO) is turned on and the wiper motor runs one cycle when changing the
wiper switch to “AUTO” position from any other positions (while the ignition key is in
“ON” position). When the wiper switch is turned to “AUTO” position again from other
positions, the system drives the wiper relay (LO) to run the wiper motor one cycle only when
the rain sensor detects the “Rain Detected” signal. 1)
2)
Rain sensing sensitivity control ▶
The wiper relay is turned on and the wiper motor runs one cycle when the volume sensitivity is
increased (ex: from 0 to 1) (while the ignition key is in “ON” position, the wiper switch is
in “AUTO” position, and the wiper motor is in “Parked” position). However, the wiper
motor can be operated only when the rain sensor detects the “Rain Detected” signal.
* If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor runs
only one cycle.