height SSANGYONG RODIUS 2007 Service Manual

0-9
PARKING AID SYSTEM
RODIUS 2006.09
8790-04
3) Cautions on parking aid system
Note that the display does not show everything in the rear area.
Always check nobody, especially animals and children, is behind the vehicle.
Normal precautions when reversing should be maintained. *
*
The parking aid system is just a supplemental device to help your parking operation.
Always keep the safety precautions.
Do not press or shock the sensors by hitting or high-pressure water gun while washing, o
r
the sensors will be damaged.
If the system is in normal operating conditions, a short beep sounds when the gear selecto
r
lever is moved into “R” position with the ignition key “ON”.
If the system is in abnormal operating conditions, a beep sounds for 3 seconds when the
gear selector lever is moved into “R” position with the ignition key “ON” or engine
running. However, it is also occurred when the obstacle is within 50 cm from the rea
r
bumper. 1.
2.
3.
4.
5.
(1) The parking aid system will not work or improperly work under
following cases:
▶Certain obstacles that sensors can not detect
- Wires, ropes, chains.
- Cotton, sponge, clothes, snow that absorb ultrasonic waves.
- Obstacles lower than the bumper.
▶Not defective but improperly working
- When the sensing portion is frozen.
- When the sensing portion is covered by rain, water drops, snow or mud.
- When receiving other ultrasonic signals
(metal sound or air braking noises from heavy commercial vehicles).
- When a high-power radio is turned on.
▶Narrowed sensing area
- When the sensing portion is partially covered by snow or mud.
<00540047007a009c009900990096009c0095008b00900095008e0047009b008c00940097008c00990088009b009c0099008c00470096008d0047009a008c0095009a0096009900470090009a0047009b009600960047008f0090008e008f0047004f008800
97009700990096009f005500470096009d008c00990047005f>0°C) or too low (approx.
below -
30°C)
▶Not defective but may occur improper working
- When driving on the rough road, gravel road, hill and grass.
- When the bumper height is changed due to the heavy load.
- When the sensing portion is frozen.
- When the sensing portion is covered by rain, water drops, snow or mud.
- When receiving other ultrasonic signals
(metal sound or air braking noises from heavy commercial vehicles).
- When a high-power radio is turned on.
- When some accessories are attached in detecting ranges

0-3
PROPELLER SHAFT
RODIUS 2006.09
3310-01
3310-01PROPELLER SHAFT
1. PROPELLER SHAFT GENERAL INFORMATION
The propeller shaft transfers the power through
the transmission and transfer case to the
front/rear axle differential carrier (final reduction
gear). It is manufactured by a thin rounded steel
pipe to have the strong resisting force against
the torsion and bending. Both ends of propelle
r
shaft are connected to the spider and the cente
r
of propeller shaft is connected to the spline to
accommodate the changes of the height and
length. The rubber bushing that covers the
intermediate bearing keeps the balance of rea
r
propeller shaft and absorbs its vibration.
2. SPECIFICATION

0-2
RODIUS 2006.09
8810-01
AIR BAG SYSTEM
8810-01AIR BAG SYSTEM
1. AIRBAG OVERVIEW
Passenger’s airbag
Airbag unit (SDM)
Driver’s airbag
Front seat
Driver’s
Passenger’s Height adjuster (Driver/passenger)

0-4
RODIUS 2006.09
7410-01
SEAT
Back flat adjust lever
Seat warmer switch
Sliding adjust lever
Seat control switch
Sliding control
1. COMPONENTS OF SEAT
Seat position control Seat height control Reclining control
Back supporter (Driver’s seat)

0-20
RODIUS 2006.09
7410-01
SEAT
Seat height (up/down)
·
Seat moves up/down controlled by
seat height control switch
:
Reclining
·
Seat back reclining controlled by seat
reclining control switch
:
Seat reclining motor