turn signal SSANGYONG RODIUS 2007 Service Manual

0-17
CIRCUIT
RODIUS 2006.09
8010-01
3)
(1) CONNECTOR INFORMATION
(2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION
WARNING (BAT CHANGE, OIL, BRAKE ENG CHCK, AIR BAG,
IMMOM SEAT-BELT) TURN SIGNAL, DEFOGGER, DOOR OPEN

0-12
RODIUS 2006.09
0000-00
CDEF(Catalytic Disel Particulate Filter)
6) CDPF Over Load (Notice of Beginning CPF Regeneration Mode
- P1430)
The CDPF system enters the regeneration mode when the mileage is around 600 ~ 1,200
km, depending on the driving condition and driving habits. At this moment, the ECU
performs the CDPF regeneration process; however, the driver may not notice anything
because there is no engine warning or other signals indicating such process.
The control logic in the regeneration process is to increase the exhaust gas temperature by
increasing the fuel injection during post injection process and controlling the intake ai
r
amount(throttle body), and no significant change can be noticed in the vehicle condition.
The engine CHECK lamp flashes but there is no decrease in engine torque.
The engine CHECK lamp flashes to inform the driver when there is an over load due to soot
accumulation because the regeneration temperature cannot be reached due to low speed,
even though CDPF regeneration is in process.
The CDPF regeneration process must be completed by driving for 15-20 minutes at a speed
higher than 80 km/h to solve this problem.
The engine CHECK lamp flashes when CDPF is over loaded; therefore, 4) above must be
performed in this case. 1.
2.
3.
4.
5.
7) CDPF's Excessive Soot Accumulation (P0432)
When the vehicle is driven at a low speed (5-10 km/h) for a long time or long distance, the
soot over accumulates inside the CDPF and the combustion temperature cannot be reached
even by performing the soot combustion process. In this case, this DTC is generated.
This is more serious situation than the CDPF over load condition. Therefore, the engine
power is decreased to protect the system and the engine CHECK lamp is turned on.
Blow the soot between the engine and the exhaust system several times and clear the DTC
to solve this problem. If the same DTC is generated again, check the system according to
the DTC description related to the differential pressure sensor.
* This DTC is actually generated mostly due to the related system malfunction, such as
differential pressure sensor malfunction. 1.
2.
3.

0-8
RODIUS 2006.09
8710-01
STICS
If the washer operating signal is inputted while the wipers are operating in intermittent or
AUTO mode, the system stores the previous intermittent interval and operates the washe
r
coupled wiper. After then, the wiper operation returns back to intermittent or AUTO mode
with the stored operating interval. 3.

0-9
STICS
RODIUS 2006.09
8710-01
(2) Rain Sensor Coupled Wiper
If equipped with RE-STICS rain sensor, has following operation system.
System layout ▶
This vehicle has a different wiper control logic compared to other models. As shown in the
system diagram, the rain sensor unit does not control wiper directly. The rain sensor unit sends
infrared rays signal through LED and then receives it with photo diode and then sends the
returned signal to STICS and the STICS controls the wipers directly.
For more details, refer to rain sensing wiper section in this manual.

0-10
RODIUS 2006.09
8710-01
STICS
Rain sensing operation point ▶
The wiper relay is turned on and the wiper motor runs one cycle when the ignition key is
turned to “ON” position (while the wiper switch is in “AUTO” position).
The wiper relay (LO) is turned on and the wiper motor runs one cycle when changing the
wiper switch to “AUTO” position from any other positions (while the ignition key is in
“ON” position). When the wiper switch is turned to “AUTO” position again from other
positions, the system drives the wiper relay (LO) to run the wiper motor one cycle only when
the rain sensor detects the “Rain Detected” signal. 1)
2)
Rain sensing sensitivity control ▶
The wiper relay is turned on and the wiper motor runs one cycle when the volume sensitivity is
increased (ex: from 0 to 1) (while the ignition key is in “ON” position, the wiper switch is
in “AUTO” position, and the wiper motor is in “Parked” position). However, the wiper
motor can be operated only when the rain sensor detects the “Rain Detected” signal.
* If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor runs
only one cycle.

0-12
RODIUS 2006.09
8710-01
STICS
Defective rain sensor ▶
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wipe
r
sensitivity is changed to 2 from 3 during receiving the malfunction signal (1) from the rain
sensor (while the ignition key is in “ON” position and the wiper switch is in “AUTO”
position). 1)
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper
sensitivity is changed to 3 from 4 during receiving the malfunction signal (2) from the rain
sensor (while the ignition key is in “ON” position and the wiper switch is in “AUTO”
position). 2)

0-13
STICS
RODIUS 2006.09
8710-01
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper
sensitivity is changed to 2 from 1 during receiving the malfunction signal (3) from the rain
sensor (while the ignition key is in “ON” position and the wiper switch is in “AUTO”
position). Also, the wiper relay (LO) is turned on and the wiper motor runs one cycle when
the wiper sensitivity is changed to 2 from 1 during receiving the ground fixed or IGN fixed
signal from the rain sensor. 3)

0-22
RODIUS 2006.09
8710-01
STICS
7) Room Lamp Control
(1) Front Room Lamp
The front room lamp comes on when opening the
driver’s door or passenger’s door while the
front room lamp switch is at door coupled position
and the key reminder switch is turned off.
The room lamp stays on for 2 seconds (T1) and
then decays through 3 seconds (T2) when
closing the driver’s door or passenger’s door.
The room lamp output should stop immediately
after turning on the ignition key during decaying
operation.
The front room lamp comes on for 30 seconds
(T3) when receiving the unlock signal from the
remote control key while the door is closed. 1.
2.
3.
4.
The front room lamp output period is extended by 30 seconds (T3) when receiving the
unlock signal from the remote control key again during output.
When a door is opened during its extended period, the lamp stays on. If closed, operates as
in step 2.
<007b008f008c004700990096009600940047009300880094009700470096009c009b0097009c009b0047009a009b00960097009a0047009000940094008c008b00900088009b008c009300a000470088008d009b008c009900470099008c008a008c009000
9d00900095008e0047009b008f008c004700930096008a0092> signal from driver’s
<008b009600960099004700880095008b004700970088009a009a008c0095008e008c009902c5009a0047008b009600960099004700930096008a00920047009a009e0090009b008a008f0047009e008f00900093008c0047009b008f008c0047008b009900
90009d008c009902c5009a0047008b00960096009900470088>nd passenger’s door
are closed. 5.
6.
7.
Door coupled front
room lamp switch

0-23
STICS
RODIUS 2006.09
8710-01
(2) Rear Room Lamp
The rear room lamp comes on when opening the
rear door while the door coupled rear room lamp
switch is pressed (except for luggage room
lamp).
The rear room lamp extends its lighting period by
5 seconds when closing the rear door.
The room lamp output stops immediately afte
r
turning the ignition key to “ON” position
during the extended period.
The room lamp output stops immediately afte
r
receiving the lock signal from the rear door lock
switch or the remote control key while the rea
r
door is closed. 1.
2.
3.
4.
Door coupled front
room lamp switch

0-26
RODIUS 2006.09
8710-01
STICS
10) Defogger Timer
The system outp<009c009b009a0047009b008f008c0047009b008800900093008e0088009b008c00530047009e00900095008b009a008f0090008c0093008b004700880095008b00470096009c009b009a0090008b008c00470099008c00880099009d0090008c009e004700
94009000990099009600990047008f008c0088009b008c008b> glass “O
signal when turning on the defogger switch (while the engine is running).
The output stops when turning on the defogger switch again during its operation.
The out
p<009c009b00470090009a004702c80076007502c9004700960095009300a00047008d009600990047005d0047009400900095009c009b008c009a0047004f007b005a00500047009e008f008c00950047009b009c0099009500900095008e004702c8007600
7502c90047009b008f008c00470099008c008800990047008b>efogger switch
within 10 minutes (T2) after completion of output.
When turning on the defogger switch again within 10 minutes (T2) after completion of initial
12 minutes (T1) of output, the output comes on for 6 minutes (T3) again once only.
<007b008f008c00470096009c009b0097009c009b0047009a009b00960097009a0047009e008f008c00950047009b008f008c00470070006e0075004700590047009a009e0090009b008a008f00470090009a0047009b009c00990095008c008b0047009b00
96004702c80076006d006d02c9004700970096009a0090009b>ion or the ALT is
“OFF”. 1.
2.
3.
4.