relay SSANGYONG TURISMO 2013 Owner's Manual

02-12
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 3 during receiving the malfunction signal (1) from the rain sensor. However, the
wiper motor can be operated only when the rain sensor detects the "Rain Detected" signal. 1)
If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor runs
only one cycle. ▶ Defective rain sensor

02-138710-01
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 3 from 4 during receiving the malfunction signal (2) from the rain sensor (while the
ignition key is in “ON” position and the wiper switch is in “AUTO” position). 2)
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 1 during receiving the malfunction signal (3) from the rain sensor (while the
ignition key is in “ON” position and the wiper switch is in “AUTO” position). Also, the wiper
relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is changed to 2
from 1 during receiving the ground fixed or IGN fixed signal from the rain sensor. 3)

02-158710-01
The wiper relay continues to output when the parking terminal is fixed at the ground or IGN
while the wiper relay is “ON” (INT switch = ON or Washer switch = ON) (The output
stops immediately after turning off the switch) - (1) Wiper MIST and washer coupled wiper
When turning on the washer switch while the wiper relay is operating.
1)
If the wiper relay “ON” request time is shorter than the remained “ON” time, it is
disregarded. -
(2) Speed sensitive INT (intermittent) wiper
The wiper relay continues to output for remaining “ON” time even when the INT switch is
turned off.
IGN 2 switch “ON”, INT switch “OFF”: resume the intermittent time when turning “ON
IGN 2 switch “OFF”, INT switch “ON”: resume the intermittent time when turning “ON 1)
2)
3)
(3) Controls when the wiper motor parking is defective

02-16
▶INT Switch Auto Position Reminder (Power-Up Reminder Wiper)
When turning off and on the auto INT switch, the system drives the wiper motor through LOW
relay regardless of communication with rain sensor.
When turning the INT-AUTO switch from the "OFF" to "ON" position with the ignition switch in
the "ON" mode, the LOW relay operates to drive the wiper motor for 1 cycle, regardless of the
rain sensor communication.
After that, when turning the INT-AUTO switch from the "OFF" to "ON" position, the LOW relay
operates to drive the wiper motor for 1 cycle only if data from the rain sensor indicates rain
drops. 1.
2.

02-278710-01
9) Battery Saver (Tail Lamp Auto Cut)
The tail lamp is turn on or off according to the operations of the multifunction tail lamp switch.
The tail lamp relay is turned off (auto cut) when opening and closing the driver’s door after
removing the ignition key without turning off the tail lamp.
Tail lamp relay is turned on when inserting the ignition key into ignition switch again after step 2
operation.
The tail lamp relay is turned off (auto cut) when opening and closing the driver’s door while the
ignition key is removed and the tail lamp is turned on. 1.
2.
3.
4.

02-298710-01
This vehicle has the windshield heated glass and the tailgate and outside rearview mirror heated glass.
The heater relay in the ICM box controls the tailgate and outside rearview mirror heated glass and its
fuse (15A) is located in the engine compartment fuse box.
Windshield, rear rear glass and outside rearview
mirror heated glass switch

02-36
12) Time Lag Power Window Control
The power window is turned off when turning the ignition key to “ON” position.
The power window relay is turned “ON” for 90 seconds (T1) when turning the ignition key to
“OFF” position.
However, the power window relay stays on for 90 seconds (T2) when the ignition key is turned to
“OFF” position while the door is opened.
The power window relay is turned “ON” again for 90 seconds (T2) just for once when
opening the door during its extended operation period of 90 seconds (T1).
The power window relay is turned “OFF” when closing the door during its extended
operation period of 90 seconds (T2). 1.
2.
3.
4.

02-378710-01
13) Theft Deterrent
(1) Description of Burglar Alarm Function
The “LOCK” output is “ON” when receiving the “LOCK” signal from transmitter while the
ignition key is removed and all doors are closed. The armed mode is activated when the door lock
switch is locked (theft deterrent horn output: once, hazard relay output: twice).
The theft deterrent horn and hazard relay outputs are “ON” when receiving the “LOCK” signal
from the remote control key again in armed mode (theft deterrent horn output: once, hazard relay
output: twice).
When receiving “LOCK” signal from the remote control key while any of doors is not closed,
only the “LOCK” output can be done and then activates the armed ready mode (without theft
deterrent horn and hazard warning flasher). At this moment, if the ignition key is in the ignition switch,
the door unlock switch is turned “ON” or the door lock switch is unlocked (after 0.6 seconds),
cancels the armed mode and activates the normal mode. However, in these cases, if closing the
door and locking the door lock switch, the theft deterrent horn outputs once and the hazard warning
flasher outputs twice and then activates armed mode.
When the door is not opened or the ignition key is not inserted into ignition switch for 30 seconds
after receiving “UNLOCK” signal, outputs “LOCK” and then activates armed mode (RELOCK
operation). Also, at this moment, the system outputs the theft deterrent horn and hazard warning
flasher.
The armed mode will not be activated except above conditions.
Ex) The armed mode will not be activated when the door is locked by the ignition key. 1.
2.
3.
4.
5.
▶Theft deterrent mode ON conditions

06-4
4) Multifunction Switch
Description Description
Multifunction
switchRated voltage DC 12 V
Operating temperature-30℃~+80℃
Rated loadLight switch ON: 1A (Relay load)
Dimmer and passing switch High beam/low beam/passing:
0.3 A (Relay load)
Turn signal switch6.6±0.5 A (Lamp load)
Wiper switchLow: 5 A (Motor load)
High: 7 A (Motor load)
Auto: 0.22±0.05 A (Relay load)
Fixed: max. 28 A (Motor load)
Washer switch 4 A (Motor load)
Intermittent wiper switch max. 25 mA
Mist switch 5 A (Motor load)

08-4
ICM box
The wiper related relays are installed in
ICM box.
Relay5
(Wiper INT-Low)Relay6
(Wiper High)
STICS
The rain sensing unit detects the amount of rain drops and sends the
operating signal to STICS, and STICS drives the wiper directly.
At this moment, STICS determines the wiper operation mode
(washer, MIST, AUTO), then sends the information to the rain
sensor.