key SUBARU BAJA 2003 1.G Owner's Manual

Keys and doors2-17
–
CONTINUED –
remote transmitter. Note that in this mode, DOORS MUST BE MANU-
ALLY LOCKED. nTo enter the passive mode
WARNING
Do not disconnect or tamper with any yellow connector and/or any harness covered with yellow insulation and/or tape.Doing so could result in accidental inflation of the SRS airbag orcould make the SRS airbag system inoperative, which may result
in serious injury.
HB2038BB
HB2036BA
1. Remove the side sill cover on the driver ’s side.
1) Open the driver ’s door.
2) Remove the two clips fastening the front portion of the cover
with a screwdriver.
3) Remove the side sill cover by pulling it up.
2. Connect the white (1 pole) connector.
3. Turn the ignition switch from “LOCK” to “ON”.
4. Install the side sill cover.
To place the system in active arming mode (remote required for ac-
tivation), disconnect the white connector.

2-18
nArming the system CAUTION
In passive mode, the system will automatically activate the alarm
but WILL NOT automatically lock the doors. In order to lock thedoors you must either lock them as indicated in step 4 below orwith the key once they have been closed. Failure to lock thedoors manually will result in a higher security risk.
HB2024DB
HB2031BB
1. Turn the ignition switch to “ON”.
2. Turn the ignition switch from “ON” to “LOCK” and remove the key
from the ignition switch.
3. Open the doors and get out of the vehicle.
4. Before closing the doors, lock all doors with the inside door locklevers.
5. Close the doors. The system will automatically arm after one min-ute.
In the passive mode, the system can also be armed with the remote
transmitter or with the power door locking switches. If the remote
transmitter or power door lock switch is used to lock the vehicle, arm-
ing will take place immediately regardless of whether or not the pas-sive mode has been selected. Disarming the system
To disarm the system, briefly press the “UNLOCK/DISARM” button on

Keys and doors2-19
–
CONTINUED –
the transmitter. Tripped sensor identification
If an electronic chirp sounds four times and the turn signal lights flash
four times when you disarm the system, this indicates that the alarm
was triggered. The number of times the indicator light flashes indi-
cates what sensor caused the alarm condition.
To enter identification mode:
1. Open the driver ’s door and leave it open.
2. Turn the ignition switch to “ON” two times. ( “LOCK” “ON”
“LOCK” “ON” “LOCK”)
3. The indicator light will start flashing.
The indicator light provides the following indications. Flashing one time: Any door has been opened.
Flashing three times: The impact sensor in the system ’s unit has
been activated. This may indicate that your vehicle has been shocked
or tampered with by some outside force and/or unauthorized person.Flashing four times: The ignition switch has been turned on or the
battery has been disconnected. NOTE The battery must be reconnected before the indicator light will flash.
To exit this mode, close the door and turn the ignition switch to “ON”.

Keys and doors2-21
–
CONTINUED –
Windows Power windows
WARNING
To avoid serious personal injury caused by entrapment, you must observe the following warnings: When operating power windows, be extremely careful to pre-
vent anyone ’s fingers, arms or head from being caught in the
window. Always lock the passengers ’ windows using the lock switch
when children are riding in the vehicle. Before leaving the vehicle, always remove the key from the
ignition switch for safety and never allow an unattended child toremain in the vehicle. Failure to follow this procedure could result
in injury to a child operating the power window.
The power windows operate only when the ignition switch is in the “ON”
position.
Driver’ s side switches
HB2008BB

Keys and doors2-23
–
CONTINUED –
Passengers’ side switches
HB2005BB
HB2009CB
To open the window, push the switch down and hold it until the win-
dow reaches the desired position. To close the window, pull the switch
up and hold it until the window reaches the desired position.
When the lock switch on the power window switch cluster, located on the driver ’s side door, is in the “LOCK” position, the passengers ’ win-
dows cannot be operated with the passengers ’ switches.
Tailgate
CAUTION
Keep the tailgate closed when the vehicle is moving. If you mustdrive with the tailgate open, use the optional Subaru BedExtender and place the License Plate Bracket at its fully lowered/
open position. Cargo must not stick out beyond the Extender.Otherwise a dangerous road hazard or personal injury couldresult.

Keys and doors2-25
–
CONTINUED –
the license plate bracket must be placed at its fully lowered/open posi-
tion to make the rear license plate visible.
CAUTION
In order to avoid damaging the license plate bracket or the bum-
per, the license plate bracket must be in its fully lowered/openposition before the tailgate is lowered.
HB2053BA
HB2054BA
To use the license plate bracket at its lowered/open position, push the
two release buttons and pull the license plate bracket up until it clicks.And then open the tailgate.
If your vehicle is equipped with a trailer hitch, remove the ball mount
from the hitch receiver tube before opening the tailgate. Failure to follow
this procedure could result in damage to the license plate bracket.
When you drive with the tailgate closed, the license plate bracket must
be restored to its original position.
To restore the license plate bracket to its original position, close the tail-gate, and then pull the license plate bracket down until it clicks.
If the license plate bracket is hard to be restored to its original position, mud may have accumulated on the back of the license plate bracket.
Remove accumulated mud before pulling the license bracket down.

Keys and doors2-27
–
CONTINUED –
To open the switchback door:
HB1112BA
1. Pull up the rear seat cushion. Refer to “Rear seats ” section in Chapter
1 for operating details.
HB1113BA
HB1112CB
2. Unlock the rear seatback by pulling up on the knob and fold down the
rear seatback. Confirm that the pins located at the bottom of the seat
cushion is inserted into the slots at the top of the seatback.

Keys and doors2-29
–
CONTINUED –
To close the switchback door, firmly push it upward until it latches.
Return the seatback and seat cushion to their original positions and
make sure they are securely locked.
CAUTION
After returning the seatback to its original position, make sure
that the rear seatback has been securely locked. When securely
locked, the red marks on the locking knobs are no longer visible.
Switchback door indicator light
HB4010JA
While the ignition switch is in the “ON” position, the switchback door indi-
cator light comes on when the switchback door is open.
While the ignition switch is in the “LOCK” or “ACC” position, the switch-
back door indicator light flashes for about 20 seconds and goes offwhen the switchback gate is open.

2-30
MoonroofWARNING
Never let anyone ’s hands, arms, head or any objects protrude
from the moonroof. He/she could be seriously injured if the
vehicle stops suddenly or turns sharply or if the vehicle is in-
volved in an accident.
To avoid serious personal injury caused by entrapment, you must observe the following warnings: Before closing the moonroof, make sure that no one ’s hands,
arms, head or other objects will be accidentally caught in themoonroof. Before leaving the vehicle, always remove the key from the
ignition switch for safety and never allow an unattended child toremain in the vehicle. Failure to follow this procedure could resultin injury to a child operating the moonroof.
CAUTION
Do not sit on the edge of the open moonroof.
Do not operate the moonroof if falling snow or extremely cold
conditions have caused it to freeze shut.
Tilting/sliding moonroof
The moonroof has both tilting and sliding functions.
The moonroof operates only when the ignition switch is in the “ON” posi-
tion.

Keys and doors2-31
–
CONTINUED –
HB2034BB
To raise or lower the moonroof
The tilting function will only operate when the moonroof is fully closed.
Push the rear side of the “Tilt” switch to raise the moonroof.
Push the front side of the “Tilt” switch to lower the moonroof.
Release the switch after the moonroof has been raised or has been
lowered completely. Pushing the switch continuously may cause dam-
age to the moonroof. To open or close the moonroof
Push the “Open/Close” switch rearward to open the moonroof. The
sun shade will be also opened together with the moonroof. Push the “Open/Close” switch forward to close the moonroof. The
moonroof will stop halfway if you continue to press on the switch.
Release the switch once and push it again to close the moonroof
completely.
After washing the vehicle or after it rains, wipe away water on the roof
prior to opening the moonroof to prevent water drops from falling into
the passenger compartment.
NOTE If the moonroof cannot be closed through the switch operation
because of system failure, it can be closed manually using a hex-headed wrench. For the procedure, refer to “Moonroof — if the
moonroof cannot be closed ” in Chapter 9 “In case of emer-