key SUBARU BAJA 2006 1.G Owner's Manual

2-19
Keys and doors
– CONTINUED –
: Press to Arm the system.
: Press to Disarm the system. 1) Security indicator light
6. Briefly press the “ ” button (for less than two sec-
onds). All doors will lock, an electronic chirp will sound
once, the turn signal lights will flash once, and the in-
dicator lights will start flashing rapidly. After rapid
flashing for 30 seconds (standby time), the indicator
lights will then flash slowly (twice approximately every
two seconds), indicating that the system has been
armed for surveillance.
If any of the doors is not fully closed, an electronic
chirp sounds five times, the turn signal lights flash five
times to alert you that the doors are not properly
closed. When you close the door, the system will au-
UG2042BA
1
UB2033BB

2-20
Keys and doors
tomatically arm and doors will automatically lock. T
To arm the system using power door locking
switches
1. Close all windows.
2. Remove the key from the ignition switch.
3. Open the doors and get out of the vehicle.
4. Make sure that the engine hood is locked.
5. Close the doors but leave only the driver’s door or
the front passenger’s door open.
6. Push the front side (“LOCK” side) of the power door
locking switch to set the door locks.
7. Close the door. An electronic chirp will sound once,
the turn signal lights will flash once, and the indicator lights will start flashing rapidly. After rapid flashing for
30 seconds (standby time), the indicator lights will
then flash slowly (twice approximately every two sec-
onds), indicating that the system has been armed for
surveillance.
NOTE y
The system can be armed even if the engine
hood, the windows and/or moonroofs are opened.
Always make sure that they are fully closed before
arming the system. y The 30-second standby time can be eliminated if
you prefer. Have it performed by your SUBARU
dealer. y The system is in the standby mode for a 30-sec-
ond period after locking the doors with the remote
transmitter. The security indicator light will flash
at short intervals during this period. y If any of the following actions is done during the
standby period, the system will not switch to the
surveillance state.
yDoors are unlocked using the remote trans-
mitter.y Any door is opened.
y Ignition switch is turned to the “ON” position.
y The engine does not start even when the igni-
tion switch is turned to the “START” position once
the alarm system has been triggered.
200889

2-21
Keys and doors
– CONTINUED –
„Disarming the system„
Disarming the systemBriefly press the “ ” button (for less than two sec-
onds) on the remote transmitter. The driver’s door will
unlock, an electronic chirp will sound twice, the turn
signal lights will flash twice and the indicator light will
go off.
NOTE
The system can be disarmed by the following
method. yCycle the ignition switch from the “LOCK” to the
“ON” position three times within 5 seconds. T Emergency disarming
If you cannot disarm the system using the transmitter
(i.e. the transmitter is lost, broken or the transmitter
battery is too weak), yo u can disarm the system with-
out using the transmitter.
1. Unlock the door with the key and then open the
door.
2. Insert the key into the ignition switch and cycle it
from the “LOCK” to the “ON” position three times with-
in 5 seconds .
„ Valet mode
„Valet modeWhen you choose the valet mode, the security system
does not operate. In valet mode, the remote transmit- ter is used only for locking and unlocking the doors
and panic activation.
To enter the valet mode, chang
e the setting of your ve-
hicle’s alarm system for deactivation mode. (Refer to
“Activating and deactivating the alarm system” in thissection.)
To exit valet mode, change the setting of your vehi-
cle’s alarm system for activation mode. (Refer to “Ac- tivating and deactiva ting the alarm system” in this sec-
tion.)
NOTE
The security indicator light does not flash during the valet mode. „ Passive arming
When passive arming mode has been programmed by
the dealer, arming of the syst em is automatically ac-
complished without using the remote transmitter. Note
that in this mode, DOORS MUST BE MANUALLY LOCKED. T To enter the passive mode
If you wish to program the passive arming mode, have
it done by your SUBARU dealer.

2-22
Keys and doors
T
Arming the system
1. Turn the ignition switch to the “ON” position.
1) ON
2) LOCK
2. Turn the ignition switch from “ON” to “LOCK” posi-
tion and remove the key from the ignition switch. 3. Open the doors and get out of the vehicle.
4. Before closing the doors, lock all doors with the in-
side door lock levers.
5. Close the doors. The system will automatically arm
after one minute.
In the passive mode, the system can also be armed
with the remote transmitter or with the power door
locking switches. If the remote transmitter or power
door locking switch is used to lock the vehicle, arming
will take place immediately regardless of whether or
not the passive mode has been selected.
1
2
HS2024BC
4
3
5
UB2024DC

2-23
Keys and doors
– CONTINUED –
In passive mode, the system will automatically
activate the alarm but WILL NOT automatically
lock the doors. In order to lock the doors you
must either lock them as indicated in step 4
above or with the key once they have been
closed. Failure to lock the doors manually will
result in a higher security risk.
T Disarming the system
T
Disarming the systemTo disarm the system, brie fly press the “ ” button
on the transmitter. „ Tripped sensor identification
The security indicator light flashes when the alarm system has been tri ggered. Also, the number of flash-
es indicates the location of unauthorized intrusion or
the severity of impact on the vehicle. y When the ignition switch is turned to the “ON” posi-
tion, the indicator light will light for 1 second and then
flash as follows: When a door was opened: 5 times
When the ignition switch was turned to the “ON” po-
sition: 3 times
When a strong impact or multiple impacts were sensed: twice (only vehicles with shock sensors
(dealer option))
When a light impact was sensed: once (only vehi-
cles with shock sensors (dealer option))
NOTE
Any of the above indicator light flashings will re-
cur each time the ignition
switch is turned to the
“ON” position. Rearming the alarm system can-
cels the flashing. „ Shock sensors (dealer option)
The shock sensors trigger the alarm system when
they sense impacts applied to the vehicle and when
any of their electric wires is cut. The alarm system
causes the horn to sound and the turn signal lights to
flash for a short time when the sensed impact is weak,
but it warns of a strong im pact or multiple impacts by
sounding the horn and flashing the turn signal lights,
both lasting approximately 30 seconds.
If you desire, your SUBARU dealer can connect them
and set them for activation or deactivation.
NOTE y The shock sensors are not always able to sense
impacts caused by breaking in, and cannot sense
an impact that does not cause vibration (such as

2-24
Keys and doors
breaking the glass using a rescue hammer). y
The shock sensors may sense vibration like
those shown in the following and trigger the alarm
system. Select the settings of the alarm system
and shock sensors appropriately depending on
where you usually park your vehicle.
Example: Vibration from construction site
Vibration in multistory car park
Vibration from trains
y You can have the sensitivity of the shock sen-
sors adjusted to your preference by your SUBARU
dealer.Child safety locksChild safety
Locks
Always use the child safety lock whenever a
child rides in the rear seat. Serious injury could
result if a child accidentally opened the door
and fell out.
1) Lock
2) Unlock
Each rear door has a child safety lock that prevents
1 2
UB2002BB

2-25
Keys and doors
– CONTINUED –
the doors from being opened even if the inside door
handle is pulled.
When the child safety lock le ver is in the lock position,
the door cannot be opened from inside regardless of
the position of the inner door handle lock lever. The
door can only be opened from the outside.WindowsWindows
„ Power windows„Power
„ Windows
To avoid serious personal injury caused by en-
trapment, you must do the following. yWhen operating the power windows, be ex-
tremely careful to prevent anyone’s fingers,
arms, neck or head from being caught in the
window.y Always lock the passengers’ windows using
the lock switch when children are riding in thevehicle.y Before leaving the vehicle, always remove
the key from the ignition switch for safety and
never allow an unattended child to remain in
the vehicle. Failure to follow this procedure
could result in injury to a child operating the
power window.
The power windows operate only when the ignition
switch is in the “ON” position.

2-26
Keys and doors
T
Driver’s side switches
1) Lock switch
2) For driver’s window
3) For rear left passenger’s window
4) For front passenger’s window
5) For rear right passenger’s window
All door windows can be controlled by the power win-
dow switch cluster at the driver side door. V
Operating the driver’s window
1) Lock
2) Unlock
3) Close
4) Open
5) Automatically open
To open:
Push the switch down lightly and hold it. The window
will open as long as the switch is held.
This switch also has a one-touch auto down feature
that allows the window to be opened fully without hold-
ing the switch.
Push the switch down until it clicks and release it, and
the window will fully open. To stop the window half-
1
2
3 4
5
UB2008BB
1 2 3
4
5 3
4
UB2008DB

2-27
Keys and doors
– CONTINUED –
way, pull the switch up lightly.
To close:
Pull the switch up lightly and hold it. The window will
close as long as the switch is held. VOperating the passengers’ windows
To open the passengers’ windows, push the appropri-
ate switch down and hold it until the window reaches
the desired position. To close the window, pull the
switch up and hold it until it reaches the desired posi-tion. V Locking the passengers’ windows
To lock the passengers’ windows, push the lock
switch. When the lock switch is in the “LOCK” position,
the passengers’ windows cannot be opened or closed.
Press the switch again to cancel the passengers’ win-
dow locking. T
Passengers’ side switches
Front passenger’s window switch
1) Open
2) Close
1 2UB2009CB

2-28
Keys and doors
Rear passenger’s window switches
1) Open
2) Close
To open the window, push the switch down and hold it
until the window reaches the desired position. To
close the window, pull the switch up and hold it until
the window reaches the desired position.
When the lock switch on the power window switch
cluster, located on the driver’s side door, is in the
“LOCK” position, the pass engers’ windows cannot be
operated with the passengers’ switches.
TailgateTailgate
Keep the tailgate closed when the vehicle is
moving. If you must drive with the tailgate
open, use the optional SUBARU Bed Extender
and place the License Plate Bracket at its fully
lowered/open position. Cargo must not stick
out beyond the Extender. Otherwise a danger-
ous road hazard or personal injury could result.
Before opening the tailgate, remove any object on the
2 1
UB2005BB
UB2050BA