ECU SUBARU BAJA 2006 1.G Manual PDF

9-16
In case of emergency
9. Use the wheel nut wrench to securely tighten the
wheel nuts to the specified torque, following the tight-
ening order in the illustration. The torque for tightening
the nuts is 74 to 89 lbf·ft (100 to 120 N·m, 10 to 12
kgf·m). This torque is equivalent to applying approxi-
mately 88 to 110 lbs (40 to 50 kg) at the top of the
wheel nut wrench provided with your vehicle. Never
use your foot on the wheel nut wrench or a pipe exten-
sion on the wrench because you may exceed the
specified torque. Have the wheel nut torque checked
at the nearest automot
ive service facility.
T Storage of the flat tire
ySecure the flat tire in the cargo bed (with the
outer side of the wheel facing up) by using the
designated tire holding rod and retainer. If the
flat tire is not properly secured, it may fall out
and create a dangerous road hazard that could
lead to a serious accident. y Do not store the flat ti re under the floor. Do-
ing so could damage the underside of the vehi-
cle.
1. Take the tire holding rod and retainer out of the tool bag.
2. Remove the rubber cap from the cargo bed. Store
the rubber cap in a safe place. Pay attention not to
lose the rubber ca
p after removal.
UB9077BA

9-17
In case of emergency
– CONTINUED –
1) Holding rod
2) Retainer
3. Place the flat tire in the cargo bed with the outer
side of the wheel facing up. For an aluminum wheel,
remove the center cap before placing it in the cargo
bed.
4. Place the retainer on the center hole of the wheel
as illustrated and put the tire holding rod into the re-
tainer.
If the flat tire is separated from its wheel completely,
the retailer should be placed upside down on the
wheel. 5. Secure the flat tire by tightening the tire holding rod.
The tire holding rod and retainer are designed solely
to secure a flat tire in emergency. Do not use them for
another purpose such as securing cargo.
6. Store the jack and wheel nut wrench in their stor-
age locations.
7. Put the rubber cap back in its original position after
everything has been restored. T
Driving with the temporary spare tire
Your spare tire is only a temporary spare which is de-
signed for temporary emergency use only. When driv-
ing with the temporary spare tire, follow the instruc-
1
2
UB9062BBUB9063BA

9-25
In case of emergency
– CONTINUED –
Vehicle with trailer hitch (if equipped)
1) Tie-down hook T
Towing hook cover removal procedure
The towing hook cover is secured by tabs that fit into
corresponding slots in the vehicle body.
To remove the cover:
1. Free the tabs on the towing hook cover by firmly
pressing the point indicated by an arrow with the palm
of your hand.
1UB9010BB
UB9083BA

9-26
In case of emergency
2. Pull off the towing hook cover.
T
Towing hook cover installation procedure
To reinstall the towing hook cover, push it in on both
sides while pushing it back to its original position.
Make certain that the tabs at the end of the cover are
securely inserted into the corresponding slots in the vehicle’s body.
UB9084BA
UB9069BA

9-27
In case of emergency
– CONTINUED –
„Using a flat-bed truck
This is the best way to transport your vehicle. Use the
following procedures to ensure safe transportation.
1. Shift the selector lever into the “P” position for au-
tomatic transmission vehi cles or “1st” for manual
transmission vehicles.
2. Pull up the parking brake lever firmly.
3. Secure the vehicle onto the carrier properly with
safety chains. Each safety chain should be equally
tightened and care must be taken not to pull the chains
so tightly that the suspension bottoms out. „
Towing with all wheels on the ground
yNever turn the ignition switch to the “LOCK”
position while the vehicle is being towed be-
cause the steering wheel and the direction of
the wheels will be locked.y Remember that the brake booster and power
steering do not function when the engine is not
running. Because the engine is turned off, it will
take greater effort to operate the brake pedal
and steering wheel.
UB9072AAUB9071AA

11 - 6
Maintenance and service
3. Release the secondary hood release located under
the front grille by moving
the lever toward the left. 4. Lift up the hood, release the hood prop from its re-
tainer and put the end of the hood prop into the slot in
the hood.
To close the hood:
1. Lift the hood slightly and remove the hood prop
from the slot in the hood and return the prop to its re-
tainer.
2. Lower the hood until it approaches approximately 6
in (15 cm) from the closed position and let it drop.
3. After closing the hood, be sure the hood is securely
locked.
If this does not close the hood,
release it from a slightly
higher position. Do not push the hood forcibly to close
UBB094BAUBB003BA

11 -1 3
Maintenance and service
– CONTINUED –
oil.
1) Sealing washer
2) Drain plug
5. Wipe the seating surface of the drain plug with a
clean cloth and tighten it securely with a new sealing
washer after the oil has completely drained out. 6. Remove three clips at the front of the cover under
the oil filter.
1
2UBB051BB
UBB054BA

11 - 2 0
Maintenance and service
Turbo models
2. Place a proper container under the drain plug and
loosen the drain plug.
Never attempt to remove the radiator cap until
the engine has been shut off and has cooled
down completely. Since the coolant is under
pressure, you may suffer serious burns from a
spray of boiling hot coolant when the cap is re-
moved. 3. Loosen the radiator cap to drain the coolant from
the radiator. Then drain the coolant from the reserve
tank. Tighten the drain plug securely.
NOTE (Turbo models)
The cap (without tabs) on top of the radiator does
not need to be removed. To add coolant, remove
the cap (with tabs) on th
e coolant tank on top of
the engine.
Non-turbo models
1) Filler neck
2) Fill up to here
UBB104BA1 2
UBB007CB

11 -2 3
Maintenance and service
– CONTINUED –
Air cleaner elementAir cleaner element
Do not operate the engine with the air cleaner
element removed. The air cleaner element not
only filters intake air but also stops flames if the
engine backfires. If the air cleaner element is
not installed when the engine backfires, you
could be burned.
The air cleaner element func tions as a filter screen.
When the element is perforated or removed, engine
wear will be excessive and engine life shortened.
The air cleaner element is a viscous type. It is unnec-
essary to clean or wash the element. „ Replacing the air cleaner element
„Replacing
„ Air cleaner element
TNon-turbo models
Replace the air cleaner element according to the
maintenance schedule in the “Warranty and Mainte-
nance Booklet”. Under extremely dusty conditions, re-
place it more frequently. It is recommended that you
always use genuine SUBARU parts.
0
1) Bolt
1. Remove the bolt securing the rear air cleaner ele- ment case.
2. Unsnap the three clamps holding the rear air clean-
er element case.
1
UBB063BB