water pump SUBARU BRZ 2023 Owners Manual

Flat Tires
310Sealant bottle
1) Hose
2) Valve1) Expiration date
▼How to seal the flat tireTo seal the flat tire, perform the following
steps.
 First, pump in the sealant and air. Drive
the vehicle for approximately 10 minutes or 3 miles (5 km) so that the sealant can

seal the damaged area.
 Stop the vehicle again, check and, if
necessary, adjust the pressure of the
damaged tire.
 After that, you can continue to drive
carefully no faster than 50 mph (80 km/h)
and within the maximum distance of 125
miles (200 km).
Inform all other users of the vehicle that
the tire has been temporarily sealed with
the flat tire repair kit and make them aware
of the special driving conditions to be
observed.
WARNING
 Do not drink the sealant. If the
sealant is accidentally swal-
lowed, seek medical attention
immediately. If the sealant splashes onto your
skin or eyes, wash it away imme-
diately with plen ty of water. If
necessary, seek medical atten-
tion immediately. Keep the flat tire repair kit out of
the reach of children.
900858
1
2
If a person who is allergic to
natural rubber comes in contact
the sealant, allergy symptoms
may occur.
CAUTION
Replace the sealant bottle with a
new one before the expiration date
passes.
900883
1
BRZ_U.book 310 ページ ２０２２年３月２９日　火曜日　午後３時５９分

Replacement of Wiper Blades
367
Maintenance and Service11
– CONTINUED –
If you fill the windshield washer tank with
a fluid with a different concentration from
the one used previously, purge the old
fluid from the piping between the wind-
shield washer tank and washer nozzles by
operating the washer for a certain period
of time. Otherwise, if the concentration of
the fluid remaining in the piping is too low
for the outside temperature, it may freeze
and block the nozzles.
11-24. Replacement of Wiper BladesGrease, wax, insects, or other material on
the windshield or the wiper blade results in
jerky wiper operation and streaking on the
glass. If you cannot remove the streaks
after operating the windshield washer or if
the wiper operation is jerky, clean the
outer surface of the windshield using a
sponge or soft cloth with a neutral deter-
gent or mild-abrasive cleaner. Do not,
however, use detergent to clean the blade
rubbers. Use only a sponge or soft cloth
(and no neutral deterge nt or mild abrasive
cleaner) when you clean the blade
rubbers. If you wipe the rubber of the
blade strongly, the black coating compo-
nent will peel off, which will cause the
wiper to judder. Also, after wiping it off,
check that the rubber has not come loose.
After cleaning the window glass and wiper
blade rubbers, be sure to rinse them with
clean water. Rinse the window until the
water does not form beads on the glass.
This indicates that the glass is clean.
CAUTION
Never use engine coolant as washer
fluid because it could cause paint
damage.
CAUTION
 Adjust the washer fluid concen-
tration appropriately for the
outside temperature. If the
concentration is inappropriate,
sprayed washer fluid may freeze
on the windshield and obstruct
your view, and the fluid may
freeze in the windshield washer
tank. Be careful foreign matter does
not contaminate the washer fluid
when filling the tank. Contamina-
tion could cause malfunctions,
such as clogging the pump.
 State or local regulations on vola-
tile organic compounds may
restrict the use of methanol, a
common windshield washer anti-
freeze additive. Washer fluids
containing non-methanol anti-
freeze agents should be used
only if they provide cold weather
protection without damaging
your vehicle’s paint, wiper blades
or washer system.
CAUTION
 Do not clean the wiper blades
with gasoline or a solvent, such
as paint thinner or benzine. This
will cause deterioration of the
wiper blades.
BRZ_U.book 367 ページ ２０２２年３月２９日　火曜日　午後３時５９分