battery SUBARU FORESTER 2000 SF / 1.G User Guide

Instruments and controls3-21
–
CONTINUED –
Before turning on the wind shield wip er d eic er, remo
ve any snow from the
wind shield . To turn on the wind shield wip er d eic er, p ush the switc h. The
ind ic ator lig ht loc ated on the switc h lig hts up whi le the wind shield wip er
d eic er is op erating .
The wind shield wip er d eic er will automatic ally shut off after ab out 15 min-
utes. If the wip er b lad es have b een d eic ed c omp lete ly b efore that time,
p ush the switc h to turn it off. It also turns off w hen the ig nition switc h is
turned to the “ACC ” or “LOCK ” p osition. If d eic ing is not c omp lete when
you restart your vehic le, you have to p ush the swit c h to turn the d eic er
on ag ain. Rear window defogger switch
CAUTION
Do not use sharp instruments or window cleaner containing
abrasives to clean the inner surface of the rear window. They may
damage the conductors printed on the window. To prevent the battery from being discharged, do not operate
the defogger continuously for any longer than necessary.
The rear wind ow d efog g er op erates only when the ig n ition switc h is in
the “ON ” p osition.
HS0063
Indicator light
To turn on the d efog g er, p ush the switc h. To turn i t off, p ush the switc h

Instruments and controls3-25
–
CONTINUED –

Remote control mirror switch (if equipped)
The remote c ontrol mirrors op erate only when the ig nition switc h is in
the “ON ” or “ACC ” p osition.
HS0067
Selection switch
Direction control switch L
R
1. Press either end of the selec tion switc h, “L ” for the left and “R ” for
the rig ht.
2. Move the d irec tion c ontrol switc h in the d irec tio n you want to move
the mirror.
3. Return the selec tion switc h to the neutral p ositi on to p revent
unintentional op eration.
The mirrors c an also b e ad justed manually. Outside mirror defogger (if equipped) CAUTION
To prevent the battery from being discharged, do not operate the
defogger continuously for any longer than necessary.
The outsid e mirror d efog g er shares the switc h with rear wind ow
d efog g er.
The outsid e mirror d efog g er op erates only when the ig nition switc h is
in the “ON ” p osition.

Audio5-9
–
CONTINUED –

Automatic tuning (SCN)
Press the “SCN ” b utton to c hang e the rad io to the SCAN mod e. In th is
mod e, the rad io sc ans throug h the rad io b and until a station is found .
The rad io will stop at the station for five sec ond s while d isp laying the fre-
q uenc y, after whic h sc anning will c ontinue until th e entire b and has b een
sc anned from the low end to the hig h end .
Press the “SCN ” b utton ag ain to c anc el the SCAN mod e and to stop o n
any d isp layed freq uenc y.
When the “SCN ” b utton is p ressed for automatic tuning , stations a re
sc anned in the d irec tion of low freq uenc ies to hig h freq uenc ies only.
Automatic tuning may not func tion p rop erly if the s tation rec ep tion is
weakened b y d istanc e from the station or p roximity to tall b uild ing s and
hills. Selecting preset stations
Presetting a station with a p reset b utton allows yo u to selec t that station
in a sing le op eration. Up to six AM and FM stations eac h may b e p reset.
How to preset stations
1. Press the FM/AM selec tion switc h to selec t either FM or AM rec ep tion.
2. Press the “SCN ” b utton or tune the rad io manually until the d esire d
station freq uenc y is d isp layed .
3. Press one of the p reset b uttons for at least two seconds to store the
freq uenc y. The freq uenc y of the station will flash onc e on the d isp lay at
this time. If the b utton is p ressed for less than t wo sec ond s, the p rec ed -
ing selec tion will remain in memory. NOTE
If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stationsstored in the preset buttons are cleared. If this occurs, it is neces-sary to reset the preset buttons.

Audio5-13
–
CONTINUED –

Display mode
You c an selec t either the time d isp lay mod e or func tion d isp lay mod e b y
p ressing the “DISP/CLK ” b utton when the ig nition switc h is either “ACC ”
or “ON ” p osition.
Time display mode
When the time d isp lay mod e is selec ted , the time d i sp lay takes p rior-
ity of the func tion d isp lay. The time is shown on t he d isp lay whenever
the ig nition switc h is “ACC ” or “ON ” p osition.
When the rad io is turned on or the station is c hang ed d uring the time
d isp lay mod e, the time d isp lay is rep lac ed b y the f req uenc y d isp lay.
However, after the freq uenc y has b een d isp layed for five sec ond s, it
is rep lac ed b y the time d isp lay ag ain. Function display mode
When the func tion d isp lay mod e is selec ted , the tim e is not shown on
the d isp lay. The d isp lay ind ic ates the c urrent func tion only.
When the rad io is turned off d uring the func tion d i sp lay mod e, the
b ac k-up lig ht on the d isp lay g oes out.
Setting the time
1. Turn the ig nition switc h to “ACC ” or “ON ”.
2. To adjust hour: Press the “DISP ” b utton and the “TUNING ” b utton
ind ic ated with “ ” tog ether to ad vanc e the hours in one-hour inc remen ts.
Keep ing the b uttons p ressed ad vanc es the hours q uic kly.
3. To adjust minute: Press the ”DISP ” b utton and the “TUNING ” b utton
ind ic ated “
 ” tog ether to ad vanc e the minutes in one-minute inc r ements.
Keep ing the b uttons p ressed ad vanc es the minutes q u ic kly.
NOTE
If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, the time set-ting will be cleared. If this occurs, it is necessary to reset the time.

6-10
HS6006BB
1. Turn on the ig nition switc h to the “ACC ” p osition and the d isp lay
shows the d efault Eng lish measurement units.
2. Dep ress the “ADJ ” switc h for 5 sec ond s or more and the d isp lay
will show “DEVIATION ” tog ether with the “5 ” and “W ”.
HS6007BB
3. Chang e the measurement units b y p ressing the “MODE ” switc h
until the p rop er mod e ap p ears.
4. Press the “ADJ ” switc h to save your selec tion.
NOTE If the setting is not completed in 30 seconds, the display will
return to the initial mode. When the battery is disconnected, you may have to perform
this operation again to reset to the desired units.

Interior equipment6-19
–
CONTINUED –

Use of an electric appliance in the accessory socket or dual
power socket for a long period of time while the engine is not running can cause battery discharge. Before driving your vehicle, make sure that the plug and the
cord on your electrical appliance will not interfere with your shift-ing gears and operating the accelerator and brake pedals. If theydo, do not use the electrical appliance while driving.
HS6001BA
HS6000BA
Elec tric al p ower (12V DC) from the b attery is on ta p at the soc ket when
the ig nition switc h is either in the “ACC ” or “ON ” p osition.
You c an use an in-c ar use elec tric al ap p lianc e b y c onnec ting it to the
soc ket.

Starting and operating7-19
–
CONTINUED –
Automatic transmission
WARNING
Do not shift from the “P” or “N” position into the “D”, “3”, “2”,
“1” or “R” position while depressing the accelerator pedal. This
may cause the vehicle to jump forward or backward.
CAUTION
Shift into the “P” or “R” position only after the vehicle is com-
pletely stopped. Shifting while the vehicle is moving may cause
damage to the transmission. Do not race the engine for more than five seconds in any posi-
tion except the “N” or “P” position when the brake is set or the
tires are on blocks. This may cause the automatic transmissionfluid to overheat. Avoid shifting from one of the forward driving positions into
the “R” position or vice versa until the vehicle has completely
stopped. Such shifting may cause damage to the transmission.
The automatic transmission is elec tronic ally c ontro lled with 4-forward
sp eed s and 1-reverse sp eed .
NOTE
Immediately after a disconnected battery is reconnected or ATF (au- tomatic transmission fluid) is replaced, you may feel that the auto-matic transmission operation is somewhat unusual.This results from erasure or invalidation of data which the on-boardcomputer has collected and stored in memory to allow the transmis-sion to shift at the most appropriate times for the current conditionof your vehicle. Optimized shifting will be restored as the vehiclecontinues to be driven for a while.

In case of emergency8-3
–
CONTINUED –

If steam is coming from the engine compartment
Turn the eng ine off and g et everyone away from the vehic le until it
c ools d own. If no steam is coming from the engine compartment
1. Keep the eng ine running at id ling sp eed .
2. Op en the hood to ventilate the eng ine c omp artment .
Confirm that the c ooling fan is turning . If the fan is not turning , im-
med iately turn the eng ine off and c ontac t your auth orized d ealer for
rep air.
3. After the eng ine c oolant temp erature has d rop p ed , turn off the en-
g ine.
If the temp erature g aug e stays at the overheated zo ne, turn the en-
g ine off.
4. After the eng ine has fully c ooled d own, c hec k the c oolant level in
the reserve tank.
If the c oolant level is b elow the “MIN ” mark, ad d c oolant up to the
“ MAX ” mark.
5. If there is no c oolant in the reserve tank, ad d c oolant to the reserve
tank. Then remove the rad iator c ap and fill the rad iator with c oolant.
If you remove the rad iator c ap from a hot rad iator, first wrap a thic k
c loth around the rad iator c ap , then turn the c ap c o unterc loc kwise
slowly without p ressing d own until it stop s. Releas e the p ressure from
the rad iator. After the p ressure has b een fully rel eased , remove the
c ap b y p ressing d own and turning it.
Jump starting
WARNING
Battery fluid is SULFURIC ACID. Do not let it come in contact
with the eyes, skin, clothing or the vehicle. If battery fluid gets on you, thoroughly flush the exposed area
with water immediately. Get medical help if the fluid has enteredyour eyes.

8-4If battery fluid is accidentally swallowed, immediately drink a
large amount of milk or water, and obtain immediate medicalhelp.
Keep everyone including children away from the battery.
The gas generated by a battery explodes if a flame or spark is
brought near it. Do not smoke or light a match while jump start-ing. Never attempt jump starting if the discharged battery is frozen.
It could cause the battery to burst or explode. Whenever working on or around a battery, always wear suit-
able eye protectors, and remove metal objects such as rings,
bands or other metal jewelry. Be sure the jumper cables and clamps on them do not have
loose or missing insulation.Do not jump start unless cables in suitable condition are avail-able. A running engine can be dangerous. Keep your fingers, hands,
clothing, hair and tools away from the cooling fan, belts and anyother moving engine parts. Removing rings, watches and ties isadvisable.
When your vehic le d oes not start d ue to a run d own (d isc harg ed ) b at-
tery, the vehic le may b e jump started b y c onnec ting your b attery to
another b attery (c alled the b ooster b attery) with j ump er c ab les.
Jump starting is d ang erous if it d one inc orrec tly. If you are unsure ab out
the p rop er p roc ed ure for jump starting , c onsult a c omp etent mec hanic .
How to jump start
1. Make sure the b ooster b attery is 12 volts and the neg ative terminal
is g round ed .
2. If the b ooster b attery is in another vehic le, d o not let the two ve-
hic les touc h.
3. Turn off all unnec essary lig hts and ac c essories.
4. Connec t the jump er c ab les exac tly in the seq uenc e illustrated .

In case of emergency8-5
–
CONTINUED –
HS0147
14 2
3
Booster battery
Engine lifting bracket
1 Connec t one jump er c ab le to the p ositive (+ ) termin al on the
d isc harg ed b attery. 2 Connec t the other end of the jump er c ab le to the p o sitive (+ )
terminal of the b ooster b attery.3 Connec t one end of the other c ab le to the neg ative (– ) terminal
of the b ooster b attery.4 Connec t the other end of the c ab le to the eng ine li fting b rac ket.
Make sure that the c ab les are not near any moving p arts and that
the c ab le c lamp s are not in c ontac t with any other metal.
5. Start the eng ine of the vehic le with the b ooster b attery and run it at
mod erate sp eed . Then start the eng ine of the vehic l e that has the d is-
c harg ed b attery.
6. When finished , c arefully d isc onnec t the c ab les in exac tly the re-
verse ord er.