lock SUBARU FORESTER 2001 SF / 1.G Service Manual

Instruments and controls3-33
–
CONTINUED –

Outside mirror defogger (if equipped) CAUTION
To prevent the battery from being discharged, do not operate the
defogger continuously for any longer than necessary.
The outside mirror defogger shares the switch with rear window
defogger.
The outside mirror defogger operates only when the ignition switch is in the “ON” position.
HS0063
Indicator light
To turn on the outside mirror defogger, push the switch. To turn it off, push the switch again.
The indicator light located on the switch is on while the outside mirror
defogger is operation. The defogger will automatically shut off after
about 15 minutes. If the mirror clears before that time, push the switch
to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when
you restart your vehicle, you have to push the switch to turn it onagain.
NOTE While the outside mirror defogger is operating, the rear window defogger also operates

5-6Choose desired volume level for each mode by turning the volume
control dial. The control function returns to volume control mode after
about 5 seconds.
To change control modes:
Each brief press of the “AUDIO” button
2 changes control modes in the following sequence starting from vol-
ume control mode. (When the radio is first turned on, the control mode
is in the volume control.)
Volume Bass Treble Fader Balance
The “AUDIO” button 2 is used for selecting the following control
modes:
Display
Control mode
HB5036BA
Turn counterclockwiseTurn clockwise
BASBass controlFor less bassFor more bass
TRETreble controlFor less trebleFor more treble
FA dFader controlTo increase rear speaker
volume and decrease front
speaker volumeTo increase front speaker
volume and decrease rear
speaker volume
BALBalance controlTo increase left speaker
volume and decrease right
speaker volumeTo increase right speakervolume and decrease left
speaker volume
VOLVolume controlFor less volumeFor more volume
Waveband selection
Push the “BAND” button 3 to select FM1, FM2 or AM reception. The
display indicates which one is currently selected.

Audio5-9
–
CONTINUED –

Never expose cassettes to heat, direct sunlight or moisture.
Clean the tape head (once or twice a month) using a wet-type
cleaning cassette .
Cassette slot
Insert a cassette with the exposed tape side facing to the right. After
insertion, playback starts. TAPE button
Press the “TAPE button ”
9 when the cassette left in the cassette slot
is to be played back again. Tape travel indicators
These indicate the direction the cassette tape is moving. : Indicates that the top side of the cassette is being played back.
: Indicates that the bottom side of the cassette is being played
back. Program button (PROG)
When the program button Y is pressed during playback, the tape
travel indicators will switch and the player will begin playing back the opposite side of the tape. The same mechanism is automatically acti-
vated when the end of the tape is reached. This allows the opposite
side of the tape to play, providing continuous playback. Fast-forward button (FF)
To fast-forward the tape, press the “FF” button
E. To stop fast-for-
warding, lightly press the “
” 8 button.
Rewind button (REW)
To rewind the tape, press the “REW” button R. To stop rewinding,
lightly press the “
” 8 button.
Eject button (
)
When “
” button 8 is pressed, playback stops and the cassette
tape is ejected. The ejection function is also active when the ignition switch is in the
“LOCK” position. Always make certain that you remove the cassette
tape.

Audio5-17
–
CONTINUED –
trols when the
“BAL/FAD” button 6 is in the depressed position.
Display
Control mode
HB5036BA
Turn counterclockwiseTurn clockwise
BASBass controlFor less bassFor more bass
TRETreble controlFor less trebleFor more treble
BALBalance controlTo increase left speaker
volume and decrease right
speaker volumeTo increase right speakervolume and decrease left
speaker volume
FA dFader controlTo increase rear speaker
volume and decrease front
speaker volumeTo increase front speaker
volume and decrease rear
speaker volume
VOLVolume controlFor less volumeFor more volume
nTone control
The volume control dial 7 normally function as volume control. The
dial become a control for Bass or Treble when you select the ap-
propriate tone control mode.
Choose desired level for each mode by turning the volume control
dial. The control function returns to volume control mode after about 5seconds.
To change control modes: Each brief press of the “BAS/TRE” button
8 changes control modes in the following sequence starting from
bass control mode. (When the radio is first turned on, the control
mode is in the volume control.)
Bass Treble Volume(BAS) (TRE) (VOL)

Audio5-19
–
CONTINUED –

Manual tuning (TUNE)
HS5005BA
nManual tuning
Turn the tuning knob 4 clockwise and release it immediately to
increase the tuning frequency and turn the tuning knob counterclock-
wise and release it immediately to decrease the tuning frequency.
Each time the knob is turned, the frequency changes 10 kHz in theAM waveband and 0.2 MHz in the FM waveband. n Seek tuning
Turn the tuning knob 4 and hold it for more than a half second. Seek
tuning will operate and stop automatically on the next station.
Continue this operation until you find the desired station. Automatic tuning (SCAN)
Press the “SCAN” button
3 to change the radio to the SCAN mode. In
this mode, the radio scans through the radio band until a station is
found. The radio will stop at the station for five seconds while display-
ing the frequency, after which scanning will continue until the entire
band has been scanned from the low end to the high end.
Press the “SCAN” button again to cancel the SCAN mode and to stop
on any displayed frequency.
When the “SCAN” button is pressed for automatic tuning, stations are
scanned in the direction of low frequencies to high frequencies only.
Automatic tuning may not function properly if the station reception is
weakened by distance from the station or proximity to tall buildings and
hills.
: Increase the tuning
: Decrease the
tuning
❚: Increase the seak
tuning
❚ : Decrease the seak
tuning

5-22n
When cassette tape is in the player
When the “TAPE” button E is pressed, the display will show “PLAY”
and the player will start playback. Tape travel indicators
These indicate the direction the cassette tape is moving. : indicates that the top side of the cassette is being played back.
: indicates that the bottom side of the cassette is being played
back. Program switching button (PROG)
When the program switching button “PROG”
U is pressed during
playback, the tape travel indicators will switch and the player will be- gin playing back the opposite side of the tape. The same mechanism
is automatically activated when the end of the tape is reached. This
allows the opposite side of the tape to play, providing continuousplayback. Fast-forward button (FF)
To fast-forward the tape, press the “FF” button
Y. The display will
show “FF”. To stop fast-forwarding, press the “FF” or “TAPE” E button.
Rewind button (REW)
To rewind the tape, press the “REW” button I. The display will indi-
cate “REW” . To stop rewinding, press the “REW” or “TAPE” E button.
Eject button (
)
When “
” button Q is pressed, play back stops and the cassette
tape is ejected. The ejection function also operates when the ignition switch is in the
“LOCK” position. Always make certain that you remove the cassette
tape. Tape program sensor button (TPS)
n Blank skip
When the “TPS” button
R is pressed, the “TPS” indicator will come on
and the player will automatically skip any blank portion of 15 second
or more and play the next program, even if it is on the other side. To
cancel blank skip mode, press the “TPS” button again.

Audio5-27
–
CONTINUED –

To select a song from its beginning and fast forward/fast re- verse
HS5005BA
nForward direction
Turn the “FF/FR and UP/DOWN ” knob G clockwise and release it
immediately to skip to the beginning of the next track. Each time the
knob is turned and released, the indicated track number will increase. n Backward direction
Turn the “FF/FR and UP/DOWN ” knob
G counterclockwise and
release it immediately to skip to the beginning of the current track. If
you continue to turn and release the knob, the indicated truck number
will decrease. n Fast forward
Turn the “FF/FR and UP/DOWN ” knob
G clockwise and hold it contin-
uously for more than 2 seconds to fast forward the disc.
Release the knob to stop fast forwarding. n Fast reverse
Turn the “FF/FR and UP/DOWN ” knob G counterclockwise and hold it
continuously for more than 2 seconds to fast reverse the disc.
Release the knob to stop fast reverse. Repeat playback
Press the “RPT” button H while a song is playing to play the song
repeatedly. The “RPT” indicator will come on and the song will be
❚: Forward direction
❚ : Backward direction
: Fast forward
: Fast reverse

5-30
If you have loaded fewer than 6 discs, any missing disc is
automatically skipped. Selection of a desired disc
Press the desired “Disc select ” buttons
V (numbered from 1 to 6) and
the disc will begin to play. To select a song from its beginning and fast forward/fast re- verse
HS5005BA
nForward direction
Turn the “FF/FR and UP/DOWN ” knob C clockwise and release it
immediately to skip to the beginning of the next track. Each time the
knob is turned and released, the indicated track number will increase. n Backward direction
Turn the “FF/FR and UP/DOWN ” knob
C counterclockwise and
release it immediately to skip to the beginning of the current track. If
you continue to turn and release the knob, the indicated truck number
will decrease. n Fast forward
Turn the “FF/FR and UP/DOWN ” knob
C clockwise and hold it contin-
uously for more than 2 seconds to fast forward the disc.
Release the knob to stop fast forwarding.
If you continue fast forwarding to the end of the disc, the CD changer
will automatically stop fast forwarding and change to the next disc.
❚: Forward direction
❚ : Backward direction
: Fast forward
: Fast reverse

Audio5-31
–
CONTINUED –
n
Fast reverse
Turn the “FF/FR and UP/DOWN ” knob C counterclockwise and hold it
continuously for more than 2 seconds to fast reverse the disc.
Release the knob to stop fast reverse.
If you continue fast reverse to the beginning of the disc, the CD
changer will automatically stop fast reverse and start playback begin-
ning with the first track on the current disc. Repeat
Press the “RPT” button
L while a song is playing to play the song
repeatedly. The “RPT” indicator will come on and the song will be
played continuously. To cancel the repeat mode, press the button
again. Then the “RPT” indicator goes out, and normal playback mode
is restored. Random playback
Press the “RAND” button
X while a disc is being played back to play
all songs on the disc in a random order. The “RAND” indicator will
come on and all songs on the disc will be played in a random order.
To cancel the random mode, press the button again. Then the
“RAND” indicator goes out, and normal playback mode is restored.
Scan (a convenient way to become familiar with a disc)
1. Press the “SCAN” button
K.
– The display shows “SCAN” and the track number being
scanned.– You hear the first 10 seconds of each track.
– The operation is automatically cleared after playing all pro-
grams. Then, normal playback starts.
2. Press the “SCAN” button again when you hear a track you like.
– Normal playback resumes.
To stop playback
To stop playback and switch over to the radio mode, press the
“BAND” button. To stop playback and switch over to the cassette
player mode, press the “TAPE” button.

Audio5-33
–
CONTINUED –

To insert a disc
Be sure to hold a disc with the label side (the side where titles are printed) up.Push the disc into the slot.The disc will be automatically set in position by the auto-loading
mechanism and begin playing.
The disc indicator will turn on as the CD begins playing. n Disc indicator
Lit: A disc is in the slot (When the ignition switch is in the “ON” or
“ACC” position).
OFF: No disc is loaded or the ignition switch is in the “Lock” position.
To remove disc left in slot
Simply press the “Eject button ”
3 and the disc will be ejected. This
procedures is effective even when the ignition switch is in the “LOCK”
position.n Function control
Refer to CD player control operating instructions described in the “ Type A audio set ” section.