lock SUBARU FORESTER 2003 SG / 2.G User Guide

1-19
Seat, seatbelt and SRS airbags
–CONTINUED –
4. To make the lap part tight, pull up on the shoulder
belt.
5. Place the lap belt as low as possible on your hips,
not on your waist.
Adjusting the rear seat shoulder belt anchor
height (window-side seating positions only)
The shoulder belt anchor height should be adjusted to
the position best suited for you.
To lower the anchor height, push the release button
and slide the anchor down.
To raise the anchor height, slide the anchor up. Pull
down on the anchor to make sure that it is locked in
place.
Always adjust the anchor height so that the shoulder
belt passes over the middle of the shoulder without
touching the neck.
4
5
HS1051BC
HS1052BA

1-23
Seat, seatbelt and SRS airbags
–CONTINUED –
3. After confirming that the webbing is not twisted, in-
sert the connector (tongue) attached at the webbing
endintothebuckleontheright-handsideuntilaclick
is heard.
If the belt stops before reaching the buckle, return the
belt slightly and pull it out more slowly. If the belt still
cannot be unlocked, let the belt retract slightly after
giving it a strong pull, then pull it out slowly again. 4. Insert the center seatbelt tongue plate in the center
seatbelt buckle marked “CENTER” on the left-hand
side until it clicks.
HS1059BAHS1060BA

1-27
Seat, seatbelt and SRS airbags
–CONTINUED –
Front seatbelt pretensioners
The driver’s and front passenger’s seatbelts have a
seatbelt pretensioner. The seatbelt pretensioners are
designed to be activated in the event of an accident in-
volving a moderate to severe frontal collision.
The pretensioner sensor also serves as the frontal
SRS airbag sensor. If the sensor detects a certain pre-
determined amount of force during a frontal collision,
the front seatbelt is quickly drawn back in by the re-
tractor to take up the slack so that the belt more effec-
tively restrains the front seat occupant.
When a seatbelt pretensioner is activated, an operat- ing noise will be heard and a small amount of smoke
will be released. These occurrences are normal and
not harmful. This smoke does not indicate a fire in the
vehicle.
Once the seatbelt pretensioner has been activated,
the seatbelt retractor remains locked. Consequently,
the seatbelt can not be pulled out and retracted and
therefore must be replaced.
NOTE
Seatbelt pretensioners are not designed to acti-
vate in minor frontal impacts, in side or rear im-
pacts or in roll-over accidents. The driver

1-33
Seat, seatbelt and SRS airbags
–CONTINUED –
come hot in a vehicle that has been closed up
in sunny weather; they could burn a small child.
Check the child restraint system before you
place a child in it. Do not leave an unsecured child restraint
system in your vehicle. Unsecured child re-
straint systems can be thrown around inside of
the vehicle in a sudden stop, turn or accident; it
can strike and injure vehicle occupants as well
as result in serious injuries or death to the
child.
Installing child restraint systems with
seatbelt
1. Set the child restraint system in the seating posi-
tion.
2. Run the lap and shoulder belt through or around
the child restraint system following the instructions
provided by its manufacturer. If the shoulder belt goes
in front of the child’s face or neck, put it behind the
child restraint system.
3. Insert the tongue plate into the buckle.
4. Take up the slack in the lap belt.
5. Pull out the seatbelt fully from the retractor to
change the retractor over from the Emergency Lock-
HS1073BA

1-34
Seat, seatbelt and SRS airbags
ing Retractor (ELR) to the Automatic Locking Retrac-
tor (ALR) function. Then, allow the belt to rewind into
the retractor. As the belt is rewinding, clicks will be
heard which indicate the retractor functions as ALR.
6. Before having a child sit in the child restraint sys-
tem, move it back and forth to check if it is firmly se-
cured. Sometimes a child restraint can be more firmly
secured by pushing it down into the seat cushion and
then tightening the seatbelt.
7. Pull at the shoulder portion of the belt to confirm
that it cannot be pulled out (ALR properly functioning).
If the child restraint system requires a top tether, latch
the hook onto the top tether anchor and tighten the top
tether. See the “Top tether anchorages” for additional
instructions.
8. To remove the child restraint system, press the re-
lease button on the seatbelt buckle and allow the belt
to retract completely. The belt will return to the ELR mode.
If you have any question concerning this type of child
restraint system, ask your SUBARU dealer.
NOTE
When the child restraint system is no longer in
use, remove it and restore the ELR function of the
retractor. That function is restored by allowing the
seatbelt to retract fully.
When you install a child restraint system, fol-
low the manufacturer

2-1
2
Keys and doors
Keys .............................................................. 2-2 Key number ..................................................... 2-2
Door locks .................................................... 2-3 Locking and unlocking from the outside ..... 2-3
Locking and unlocking from the inside ........ 2-4
Power door locking switches ..................... 2-5
Remote keyless entry system (if equipped) 2-6 Locking the doors ........................................... 2-7
Unlocking the doors ....................................... 2-7
Illuminated entry ............................................. 2-8
Vehicle finder function ................................... 2-8
Sounding a panic alarm ................................. 2-8
Selecting audible signal operation ............... 2-8
Replacing the battery ..................................... 2-9
Replacing lost transmitters ........................... 2-10
Security system (if equipped) ..................... 2-14 System operation ............................................ 2-14
Arming the system ......................................... 2-14
Disarming the system .................................... 2-16
Valet mode ....................................................... 2-17
Passive arming ............................................... 2-17
Child safety locks ........................................ 2-20
Windows ....................................................... 2-21 Power windows ............................................... 2-21
Rear gate ....................................................... 2-24
Moonroof (if equipped) ................................ 2-26 To open the moonroof .................................... 2-26
To close the moonroof ................................... 2-26
Anti-entrapment function ............................... 2-26

2-2
Keys and doors
Keys and doors
Keys
1) Master key
2) Submaster key
3) Valet key
4) Key number plate
Three types of keys are provided for your vehicle:
Master key, submaster key and valet key.
The master key and submaster key fit all locks on your
vehicle. Ignition switch
Driver’s door
Glove box The valet key fits only the ignition switch and driver’s
door lock. You can keep the glove box locked when
you leave your vehicle and valet key at a parking facil-
ity.
Key number
The key number is stamped on the metal plate at-
tached to the key set. Write down the key number and
keep it in another safe place, not in the vehicle. This
number is needed to make a replacement key if you
lose your key or lock it inside the vehicle.
1 2
3
4
HS2011BA

2-3
Keys and doors
– CONTINUED –
Door locks Locking and unlocking from the out- side
1) Lock
2) Unlock
To lock the door from the outside with the key, turn the
key toward the rear. To unlock the door, turn the key
toward the front (Driver’s side only).
Pull the outside door handle to open the unlocked
door. 1) Rotate the lock lever rearward.
2) Close the door.
To lock the door from the outside without the key, ro-
tate the lock lever rearward and then close the door.
To lock the door from the outside using the power door
locking switch, push the front side of the switch
(“LOCK” side) and then close the door. In this case, all
closed doors and the rear gate are locked at the same
time.
Always make sure that all doors and the rear gate are
locked before leaving your vehicle.
1
2
HS2012BB
1
2
HS2013BB

2-4
Keys and doors
NOTE
Make sure that you do not leave the key inside the
vehicle when locking th
e doors from the outside
without the key. Locking and unlocking from the inside
1) Lock
2) Unlock
To lock the door from the inside, rotate the lock lever
rearward. To unlock the door from the inside, rotate
the lock lever forward.
The red mark on the lock lever appears when the door is unlocked.
Pull the inside door handle to open an unlocked door.
Always make sure that all doors and the rear gate are
closed before starting to drive.
Keep all doors locked when you drive, especial-
ly when small children are in your vehicle.
Along with the proper use of seat belts and
child restraints, locking the doors reduces the
chance of being thrown out of the vehicle in an
accident.
It also helps prevent passengers from falling
out if a door is accidentally opened, and intrud-
ers from unexpectedly opening doors and en-
tering your vehicle.
HS2014BB
1
2

2-5
Keys and doors
– CONTINUED –
Power door locking switches
1) Lock
2) Unlock
All doors and the rear gate can be locked and un-
locked by the power door locking switches located at
the driver’s side and the front passenger’s side doors.
To lock the doors, push the front side of the switch.
To unlock the doors, push the rear side of the switch.
When you close the doors after you set the door locks,
the doors remain locked.NOTE
Make sure that you do not leave the key inside the
vehicle before locking the doors from the outside
using power door locking switches.
1
2
HS2015BB