light SUBARU FORESTER 2003 SG / 2.G Workshop Manual

3-29
Instruments and controls
–CONTINUED –
Mirrors
Always check that the inside and outside mirrors are
properly adjusted before you start driving. Inside mirror
1) Tab
The inside mirror has a day and night position. Pull the
tab at the bottom of the mirror toward you for the night
position. Push it away for the day position. The night
position reduces glare from headlights.
Auto-dimming mirror/com pass (if equipped)
1) Left button
2) Auto dimming indicator
3) Photosensor
4) Right button
The inside electronic compass mirror has an anti-glare
feature which automatically reduces glare coming
from headlights of vehicles behind you. It also con-
tains a built-in compass. By pressing and releasing the left button, the auto-
matic dimming function is toggled on or off. When the
automatic dimming function is on, the auto dimming in-
dicator light (green) located to the right of the button
1HS3036BB
1
23 4
HS3037BB

3-30
Instruments and controls
will illuminate.
By pressing and releasing the right button, the com-
pass display is toggled on or off. When the compass is
on, an illuminated compass reading will appear in the
lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror sur-
face turns bright if the transmission is shifted into re-
verse. This is to ensure good rearward visibility during reversing. Photosensors
The mirror has a photosensor attached on both the
front and back sides. If the glare from the headlights of
vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror
dimmer to help prevent you from being blinded. For
this reason, use care not to cover the sensors with
stickers, or other similar items. Periodically wipe the
sensors clean using a piece of dry soft cotton cloth or
an applicator.
Compass calibration
1. For optimum calibration, switch off all nonessential
electrical accessories (rear window defogger, heater/
air conditioning system, spotlight, etc.) and ensure all
doors are shut.
2. Drive to an open, level area away from large metal-
lic objects or structures and make certain the ignition
switch is in the “ON” position.
3. Press and hold the left button for 3 seconds then re-
lease, and the compass will enter the calibration
mode. “CAL” and direction will be displayed.
4. Drive slowly in a circle until “CAL” disappears from
the display (about two or three circles).
5. The compass is now calibrated. Further calibration
is not required. The compass will automatically cali-
brate from this point forward.
HS3038BA

3-32
Instruments and controls
determine the actual size and distance of ob-
jects that you view in convex mirror.
Remote control mirror switch
1) Selection switch
2) Direction control switch
The remote control mirrors operate only when the ig-
nition switch is in the “ON” or “ACC” position.
1. Press either end of the selection switch, “L” for the
left, “R” for the right.
2. Move the direction control switch in the direction
youwanttomovethemirror. 3. Return the selection switch to the neutral position
to prevent unintentional operation.
The mirrors can also be adjusted manually.
Outside mirror defogger
1) Outside mirror defogger switch (if equipped)
2) Outside mirror defogger and Windshield wiper deicer switch (if equipped)
The outside mirror defogger operates only when the
ignition switch is in the “ON” position.
To turn on the outside mirror defogger, push the
switch. To turn it off, push the switch again. The indi-
cator light located on the switch lights up while the out-
MIRRMIRROROR
LR1
2
HS3041BB
12
HS3046AB

4-1
4
Climate control
Ventilator ...................................................... 4-2 Air flow selection ............................................ 4-2
Center and side ventilators ............................ 4-3
Manual climate control system ................... 4-4 Control panel ................................................... 4-4
Heater operation ............................................. 4-6
Air conditioner operation (if equipped) ........ 4-9
Automatic climate control system
(if equipped) ................................................. 4-10 Temperature sensors ..................................... 4-15
Operating tips for heater and air
conditioner ................................................... 4-16 Cleaning ventilation grille .............................. 4-16
Efficient cooling after parking in direct
sunlight ............................................................ 4-17
Lubrication oil circulation in the refrigerant
circuit ............................................................... 4-17
Checking air conditioning system before
summer season .............................................. 4-17
Cooling and dehumidifying in high humidity
and low temperature weather conditions ..... 4-17
Air conditioner compressor shut-off when
engine is heavily loaded ................................ 4-17
Refrigerant for your climate control system 4-17
Air filtration system (if equipped) ............... 4-18 Replacing an air filter ..................................... 4-18

4-5
Climate control
– CONTINUED –
conditioner button will not come on. At the same
time, the air inlet selection is automatically set to
“outside air” mode.
In this state, you cannot select “recirculation”
mode by manually pressing the air inlet selection button.
Also, you cannot stop the air conditioner com-
pressor by pressing the air conditioner button. Air conditioner button (if equipped)
The air conditioner operates only when the engine is
running.
Push the air conditioner button while the fan is in op-
eration to turn on the air conditioner. The indicator light will come on.
Push it again to turn off the air conditioner.
Air inlet selection button
ON position (Recirculation): Interior air is recirculat-
ed inside the vehicle. Push the air inlet selection but-
ton to the ON position. The indicator light will come on.
OFF position (Outside air): Outside air is drawn into
the passenger compartment. Push the air inlet selec-
tion button again to the OFF position. The indicator
light will go off.
HS4012BA
HS4012CA

4-6
Climate control
Continued operation with the air inlet selection
button in the ON position may fog up the win-
dows. Switch to the OFF position as soon as
the outside dusty condition clears.
Heater operation
Defrosting or defogging the windshield
To direct warm air to the windshield and front door win-
dows: 1. Set the air flow control dial to the “ ” position.
2. Turn the temperature control dial all the way to the
right.
3. Set the fan speed control dial to the highest speed.
If your vehicle is equipped with an air conditioner,
when the “ ” or “ ” position is selected, the air
conditioner compressor automatically operates re-
gardless of the position of the air conditioner button to
defog the windshield quickly.
However, the air conditioner indicator light does not
come on at this time.
NOTE
Warm air also comes out from the right and left air
outlets. To stop warm air flow from these outlets,
turn the corresponding
thumb-wheel down.
HS4013AA

4-7
Climate control
– CONTINUED –
Heating and defrosting
To direct warm air toward the floor and the windshield:
1. Set the air flow control dial to the “ ”position.
2. Set the temperature control dial to the most com-
fortable level.
3. Set the fan speed control dial to the desired speed.
If your vehicle is equipped with an air conditioner,
when the “ ” or “ ” position is selected, the air
conditioner compressor automatically operates re-
gardless of the position of the air conditioner button to
defog the windshield quickly.
However, the air conditioner indicator light does not
come on at this time.NOTE
Warm air also comes out from the right and left air
outlets. To stop warm air flow from these outlets,
turn the corresponding thumb-wheel down. Heating
To direct warm air toward the floor:
1. Set the air inlet selection button to the OFF position
2. Set the air flow control dial to the “ ” position.
3. Set the temperature control dial to the most com-
fortable level.
4. Set the fan speed control dial to the desired speed.
HS4014AA
HS4015AA

4-8
Climate control
NOTE
Warm air also comes out from the right and left air
outlets. To stop warm air flow from these outlets,
turn the corresponding thumb-wheel down.
Bi-level heating
This setting allows you to direct air of different temper-
atures from the instrument panel and foot outlets. The
air from the foot outlets is slightly warmer than from the
instrument panel outlets.
1. Set the air inlet selection button to the OFF posi- tion.
2. Set the air flow control dial to the “ ” position.
3. Set the temperature control dial to the desired tem- perature level.
4. Set the fan speed control dial to the desired speed.
Setting the temperature control dial fully turned to the
red area or blue area decreases the temperature dif-
ference between the air from the instrument panel out-
lets and the air from the foot outlets.
Ventilation
To force outside air through the instrument panel out-
lets:
1. Set the air inlet selection button to the OFF posi- tion.
2. Set the air flow control dial to the “ ” position.
3. Set the temperature control dial all the way left.
HS4016AA
HS4017AA

4-10
Climate control

Defrosting or defogging
To direct warm air to the windshield and front door win-
dows:
1. Set the air flow control dial to the “ ” position.
2. Set the temperature control dial to the red side.
3. Set the fan speed control dial at the highest speed.
The air conditioner compressor automatically oper-
ates when the air flow control dial set in the “ ” or
“ ” position to provide better defogging perfor-
mance.
However, the air conditioner indicator light does not
come on at this time. Automatic climate control system (if
equipped)
NOTE
Operate the automatic climate control system
when the engine is running. When the engine coolant is cold, the blower
does not run. In the “AUTO” mode, when the air temperature
in the passenger compartment is sufficiently cool,
the air conditioner compressor does not operate.
For efficient defogging or dehumidifying in cold
weather, press the “A/C” switch on. Even when cooling is not necessary, setting the
temperature much lower than the current outlet air
temperature turns on the air conditioner compres-
sor automatically and the “A/C” indicator light on
the control panel comes on.
The automatic climate control system automatically
controls outlet air temperature, fan speed, air flow dis-
tribution air-inlet control, and air conditioner compres-
sor operation. It activates when the “AUTO” switch is
pressed, and is used in conjunction with the Temper-
ature control dial to maintain a constant, comfortable
climate within the passenger compartment.
The temperature can be set within a range of 65 –
HS4013AA

4-11
Climate control
– CONTINUED –
85°F(18–32 °C).
NOTE
The temperature is shown in units of Fahrenheit
for the US model and in Centigrade for the Canadi-
an model. Control panel
1) Temperature control dial
2) AUTO switch
3) Fan speed control dial
4) Air conditioner switch
5) Air flow control dial
6) Defroster switch
7) Rear window defogger switch (Refer to the “Rear win- dow defogger switch” in chapter 3.)
8) Air inlet selection switch
9) OFF/BRIGHT switch
AUTO switch
AUTO mode operation:
When the “AUTO” switch is pressed, the indicator light
on the switch illuminates, indicating that the Automatic
Climate Control system is operating in the automatic
mode. In the automatic mode, the system maintains
the desired cabin air temperature (this is set using the
temperature control dial) by automatically controlling
the fan speed, air flow mode, air inlet selection, and air
conditioner compressor operation.
123456
7
8
9
HS4019BB
HS4023BA