service SUBARU FORESTER 2003 SG / 2.G Manual PDF

11 -5 7
Maintenance and service
–CONTINUED –
Front turn signal, side marker light and
parking lights
1) Front turn signal light
2) Parking light
3) Front side marker light
The headlight assembly must be removed before the
parking light and front turn signal light bulbs can be re-
placed. When the headlight assembly has been re-
moved and then reinstalled, it may become necessary
to make a headlight aiming adjustment. It may be dif-
ficult to replace the bulbs. Have your SUBARU dealer
replace the bulbs if necessary.
:Clip
: Hook
1
3 2
HSB073BB
HSB074BA

11 - 5 8
Maintenance and service
0
1. Remove the front grille. Use a screwdriver to de-
tach the four clips at the top and the three hooks on the
left, right and center.
2. Remove the grille side cover by undoing the two
clips and sliding the grille side cover toward the head-
light.
HSB075BAHSB076BA

11 -5 9
Maintenance and service
–CONTINUED –
3. Remove three bolts. 1) Rubber cover
2) Electrical connector
3) “Top” mark
4. Disconnect the connectors from the headlight as- sembly.
HSB078BAHSB070BB
1
2
3

11 - 6 0
Maintenance and service
5. Pull the headlight assembly slightly toward you,
then hold down the lock release tabs on the connec-
tors for the front turn signal light, parking light, and
front side marker light and pull out the headlight as-
sembly completely.
6. Remove the bulb socket from the headlight assem-
bly by turning it counterclockwise.
HSB079BAHSB073CA

11 -6 1
Maintenance and service
–CONTINUED –
7. Pull the bulb out of the socket. Install a new bulb.
8. Set the bulb socket into the headlight assembly and
turn it clockwise until it locks.
9. Reinstall all the removed parts by following the re-
moval sequence in reverse. Front fog light
It may be difficult to replace the bulbs. Have your
SUBARU dealer replace the bulbs if necessary. Rear combination lights
1. Remove the upper and lower screws. Then, slide
the rear combination lamp assembly to the rear and remove it from the vehicle.
HSB080BA
HSB085BA

11 - 6 2
Maintenance and service
1) Tail/stop light
2) Rear turn signal light
3) Backup light
4) Tail/stop light
2. Remove the bulb holder from the rear combination
light assembly by turning it counterclockwise.
3. Pull the bulb from the holder. Install a new bulb.
4. Set the bulb holder into the rear combination light
assembly and turn it clockwise until it locks.
5. Reinstall the rear combination light assembly.
License plate light
0
1. Remove the mounting screws using a phillipsscrewdriver.
2. Remove the cover and lens.
3. Pull the bulb out of the socket. Install a new bulb.
4. Reinstall the lens and cover.
5. Tighten the mounting screws.
3
2
1
4
HSB086BB
HSB087BA

11 -6 3
Maintenance and service
–CONTINUED –
Dome light, map light and cargo area light
1. Remove the lens by prying the edge of the lens with
HSB088BA
HSB089BA
HSB090BA

11 - 6 4
Maintenance and service
a regular screwdriver.
2. Pull the bulb out of the socket. Install a new bulb.
3. Reinstall the lens.
High mount stop light
0
1. Remove the mounting screw covers by prying the
edge with a screwdriver.
2. Remove the mounting screws using a phillips
screwdriver and then remove the high mount stop lightcover.
3. Pull the bulb from the socket. Install a new bulb.
4. Reinstall the cover.
5. Tighten the mounting screws then reinstall the cov- ers.
NOTE
Other bulbs may be difficult to replace. Have your
SUBARU dealer replace these bulbs if necessary.
HSB091BA

13-2
Consumer information and Reporting safety defects
Consumer information and Reporting safety defectsFor U.S.A.
The following information has been compiled accord-
ing to Code of Federal Regulations “Title 49, Part
575”.
Uniform tire quality grading stan-
dards
This information indicates the relative performance of
passenger car tires in the area of treadwear, traction,
and temperature resistance. This is to aid the consum-
er in making an informed choice in the purchase of tires.
Quality grades can be found where applicable on the
tire sidewall between tread shoulder and maximum
section width. For example:
Treadwear 200 Traction AA Temperature A
The quality grades apply to new pneumatic tires for
use on passenger cars. However, they do not apply to
deep tread, winter type snow tires, space-saver or
temporary use spare tires, tires with nominal rim diam-
eters of 12 inches or less, or to some limited produc-
tion tires.
All passenger car tires must confirm to Federal Safety
Requirements in addition to these grades.
Treadwear
The treadwear grade is a comparative rating based on
the wear rate of the tire when tested under controlled
conditions on a specified government test course.
For example, a tire graded 150 would wear one and
one-half (1-1/2) times as well on the government
course as a tire graded 100. The relative performance
of tires depends upon the actual conditions of their
use, however, and may depart significantly from the
norm due to variations in driving habits, service prac-
tices and differences in road characteristics and cli- mate. Traction AA, A, B, C
The traction grades, from highest to lowest, are AA, A,
B and C. Those grades represent the tire's ability to
stop on wet pavement as measured under controlled
conditions on specified government test surfaces of
asphalt and concrete. A tire marked C may have poor
traction performance.
The traction grade assigned to this tire is based