lock SUBARU FORESTER 2006 Owners Manual

11 - 3 6
Maintenance and service
Replacement of wiper bladesGrease, wax, insects, or other material on
the windshield or the wiper blade results in
jerky wiper operation and streaking on the
glass. If you cannot remove the streaks af-
ter operating the windshield washer or if
the wiper operation is jerky, clean the out-
er surface of the windshield (or rear win-
dow) and the wiper blades using a sponge
or soft cloth with a neutral detergent or
mild-abrasive cleaner. After cleaning,
rinse the windshield and wiper blades with
clean water. The windshield is clean if
beads do not form when you rinse the
windshield with water.If you cannot eliminate the streaking even
after following this method, replace the
wiper blades using the following proce-
dures:„Windshield wiper blades1. Raise the wiper arm off the windshield.
1) Stopper2. Remove the wiper blade assembly by
holding its pivot area and pushing it in the
direction shown by the arrow while de-
pressing the wiper blade stopper.
1) Metal support3. Grasp the locked end of the blade rub-
ber assembly and pull it firmly until the
stoppers on the rubber are free of the met-
al support.
Do not clean the wiper blades with
gasoline or a solvent, such as paint
thinner or benzene. This will cause
deterioration of the wiper blades.
1
B00380
1
B00330
ProCarManuals.com

Maintenance and service
11 - 3 7
– CONTINUED –
1) Metal spines4. If the new blade rubber is not provided
with two metal spines, remove the metal
spines from the old blade rubber and in-
stall them in the new blade rubber. 5. Align the claws of the metal support
with the grooves in the rubber and slide
the blade rubber assembly into the metal
support until it locks.
1) StopperBe sure to position the claws at the end of
the metal support between the stoppers
on the rubber as shown. If the rubber is
not retained properly, the wiper blade may
scratch the windshield.
6. Install the wiper blade assembly to the
wiper arm. Make sure that it locks in place.
7. Lower the wiper arm.„
Rear window wiper blade1. Raise the wiper arm off the rear win-
dow. 2. Turn the wiper blade assembly coun-
terclockwise.
3. Having turned the wiper blade assem-
bly to the angle shown in the illustration,
pull it in the direction of the arrow to re-
move it from the wiper arm.
1
B00331B00059
1
B00332
B00061B00062
ProCarManuals.com

11 - 3 8
Maintenance and service
1) Plastic support4. Pull out the end of the blade rubber as-
sembly to unlock it from the plastic sup-
port.
5. Pull the blade rubber assembly out ofthe plastic support.
1) Metal spines6. If the new blade rubber is not provided
with two metal spines, remove the metal
spines from the old blade rubber and in-
stall them in the new blade rubber.
7. Align the claws of the plastic support
with the grooves in the blade rubber as-
sembly, then slide the blade rubber as-
sembly into place.
Securely lock the end of the plastic sup-
port as shown in the illustration. If the rub-
1B00381B00064
1
B00333
B00066B00067
ProCarManuals.com

Maintenance and service
11 - 3 9
– CONTINUED –
ber is not retained properly, the wiper may
scratch the rear window glass.
8. Install the wiper blade assembly to the
wiper arm. Make sure that it locks in place.
9. Lower the wiper arm.
BatteryyBefore beginning work on or near
any battery, be sure to extinguish
all cigarettes, matches, and light-
ers. Never expose a battery to an
open flame or electric sparks. Bat-
teries give off a gas which is high-
ly flammable and explosive.yFor safety, in case an explosion
does occur, wear eye protection
or shield your eyes when working
near any battery. Never lean over
a battery.yDo not let battery fluid contact
eyes, skin, fabrics, or paint be-
cause battery fluid is a corrosive
acid. If battery fluid gets on your
skin or in your eyes, immediately
flush the area with water thor-
oughly. Seek medical help imme-
diately if acid has entered the
eyes.
If battery fluid is accidentally
swallowed, immediately drink a
large amount of milk or water, and
seek medical attention immediate-
ly.
yTo lessen the risk of sparks, re-
move rings, metal watchbands,
and other metal jewelry. Never al-
low metal tools to contact the pos-
itive battery terminal and anything
connected to it WHILE you are at
the same time in contact with any
other metallic portion of the vehi-
cle because a short circuit will re-
sult.yKeep everyone including children
away from the battery.yCharge the battery in a well-venti-
lated area.yBattery posts, terminals and relat-
ed accessories contain lead and
lead compounds, chemicals
known to the State of California to
cause cancer and reproductive
harm. Batteries also contain other
chemicals known to the State of
California to cause cancer. Wash
hands after handling.
ProCarManuals.com

Maintenance and service
11 - 4 1
in the main fuse box cover in the engine
compartment.1) Good
2) BlownIf any lights, accessories or other electri-
cal controls do not operate, inspect the
corresponding fuse. If a fuse has blown,
replace it.
1. Turn the ignition switch to the “LOCK”
position and turn off all electrical accesso-
ries.
2. Remove the cover.
3. Determine which fuse may be blown.
The back side of each fuse box cover and
the “Fuses and circuits” section in chapter
12 in this manual show the circuit for each
fuse.4. Pull out the fuse with the fuse puller.
5. Inspect the fuse. If it has blown, re-
place it with a spare fuse of the same rat-
ing.
6. If the same fuse blows again, this indi-
cates that its system has a problem. Con-
tact your SUBARU dealer for repairs.
Main fuseMain fuse boxThe main fuses are designed to melt dur-
ing an overload to prevent damage to the
wiring harness and electrical equipment.
Check the main fuses if any electrical
component fails to operate (except the
starter motor) and other fuses are good. A
melted main fuse must be replaced. Use
only replacements with the same speci-
fied rating as the melted main fuse. If a
main fuse blows after it is replaced, have
the electrical system checked by your
nearest SUBARU dealer.
12
B00338
600160
600444
ProCarManuals.com

Maintenance and service
11 - 4 5
– CONTINUED –
„Headlights (Except Canada-
spec. 2.5XT)Before replacing the left-hand (battery-
side) low- or high-beam light bulb, remove
the screw that retains the windshield
washer nozzle and tip the windshield
washer nozzle sideways.
NOTEyIf headlight aiming is required, con-
sult your SUBARU dealer for proper
adjustment of the headlight aim.
y It may be difficult to replace the
bulbs. Have your SUBARU dealer re-
place the bulbs if necessary. T
Low beam light bulbs
1. Remove the bulb cover, by turning it
counterclockwise.
2. Remove the retainer spring, then pull
out the bulb and electrical connector unit.
B00393
Halogen headlight bulbs become
very hot while in use. If you touch
the bulb surface with bare hands or
greasy gloves, finger prints or
grease on the bulb surface will de-
velop into hot spots and cause the
bulb to break. If there are finger
prints or grease on the bulb surface,
wipe them away with a soft cloth
moistened with alcohol.
B00385B00386
ProCarManuals.com

11 - 4 6
Maintenance and service
3. Disconnect the electrical connector
from the bulb.
4. Install a new bulb into the electrical
connector, then set the retainer spring se-
curely.
5. Install the bulb cover.T
High beam light bulbs
1. Disconnect the electrical connector
from the bulb.
2. Remove the bulb from the headlight
assembly by turning it counterclockwise. 3. Replace the bulb with new one.
4. Reconnect the electrical connector. At
this time, use care not to touch the bulb
surface.
5. To install the bulb to the headlight as-
sembly, turn it clockwise until it clicks.
„
Rear combination lights1. Remove the upper and lower screws.
Then, slide the rear combination lamp as-
sembly to the rear and remove it from the
vehicle.
B00387
700093B00388
B00389
ProCarManuals.com

Maintenance and service
11 - 4 7
– CONTINUED –
1) Tail/stop light
2) Backup light
3) Rear turn signal light
4) Tail/stop light2. Remove the bulb holder from the rear
combination light assembly by turning it
counterclockwise.
3. Pull the bulb from the holder. Install a
new bulb.
4. Set the bulb holder into the rear combi-
nation light assembly and turn it clockwise
until it locks.
5. Reinstall the rear combination light as-
sembly.
„License plate light
0
1. Remove the mounting screws using a
Phillips screwdriver.
2. Remove the cover and lens.
3. Pull the bulb out of the socket. Install a
new bulb.
4. Reinstall the lens and cover.
5. Tighten the mounting screws.
„Dome light and map lightDome light
Map light1. Remove the lens by prying the edge of
1234
B00390
B00391
B00090B00091
ProCarManuals.com

12-6
Specifications
Fuses and circuits„Fuse panel located behind the instrument pan-
el
1 234 56
789101112
1413 15 16 17 18 19
20 21 22 23
C00000
Fuse panel
Fuse rating
Circuit
1
15A
y
Heater fan
2
15A
y
Heater fan
3
15A
y
Power door lock
y
Remote keyless entry
4
15A
y
Cigarette lighter
y
Remote controlled rear view mirrors
5
10A
y
Tail light
y
Parking light
6
15A
y
SRS airbag
7
15A
y
Fog light
8
30A
y
ABS
y
Vehicle Dynamics Control system
(models with Vehicle Dynamics
Control system only)
9
15A
y
Radio
10
Empty
11
15A
y
Engine ignition system
y
SRS airbag
y
AT control system
12
10A
y
Illumination brightness control
13
20A
y
Wiper deicer
y
Outside mirror defogger
ProCarManuals.com

12-8
Specifications
Fuse panel
Fuse rating
Circuit
1
30A
y
Radiator cooling fan (Main)
2
30A
y
Radiator cooling fan (Sub)
3
50A
y
Vehicle Dynamics Control system
(Models with Vehicle Dynamics
Control system only)
30A
y
ABS motor
4
30A
y
Engine sensor (Non-turbo models
only)
5
20A
y
Rear window defogger
6
15A
y
Hazard warning flasher
y
Horn
7
15A
y
Turn signal lights
8
10A
y
Automatic transmission control unit
9
10A
y
Alternator
10
15A
y
Headlight (right side)
11
15A
y
Headlight (left side)
12
20A
y
Lighting switch
13
15A
y
Clock
y
Interior light
14
10A
y
Secondary air combination valve
(Turbo models only)
Fuse panel
Fuse rating
Circuit
ProCarManuals.com