tire size SUBARU FORESTER 2006 User Guide

9-2
In case of emergency
In case of emergency
If you park your vehicle in case of an emergencyThe hazard warning flasher should be
used in day or night to warn other drivers
when you have to park your vehicle under
emergency conditions.
Avoid stopping on the road. It is best to
safely pull off the road if a problem occurs.
The hazard warning flasher can be acti-
vated regardless of the ignition switch po-
sition.
Turn on the hazard warning by pushing
the hazard warning flasher switch. Turn it
off by pushing the switch again.NOTEWhen the hazard warning flasher is on,the turn signals do not work.
Temporary spare tire (if equipped)The temporary spare tire is smaller and
lighter than a conventional tire and is de-
signed for emergency use only. Remove
the temporary spare tire and re-install the
conventional tire as soon as possible be-
cause the spare tire is designed only for
temporary use.
Check the inflation pressure of the tempo-
rary spare tire periodically to keep the tire
300117
Never tow a trailer when the tempo-
rary spare tire is used. The tempo-
rary spare tire is not designed to
sustain the towing load. Use of the
temporary spare tire when towing
can result in failure of the spare tire
and/or less stability of the vehicle
and may lead to an accident.
Never use any temporary spare tire
other than the original. Using other
sizes may result in severe mechani-
cal damage to the drive train of your
vehicle.
ProCarManuals.com

In case of emergency
9-3
– CONTINUED –
ready for use. The correct pressure is 60
psi (420 kPa, 4.2 kg/cm
2) .
When using the temporary spare tire, note
the following.
y Do not exceed 50 mph (80 km/h).
y Do not put a tire chain on the temporary
spare tire. Because of the smaller tire
size, a tire chain will not fit properly.
y Do not use two or more temporary
spare tires at the same time.
y Do not drive over obstacles. This tire
has a smaller diameter, so road clearance
is reduced.
1) Tread wear indicator bar
2) Indicator location marky When the wear indicator appears on the
tread, replace the tire.
1) Spare fuse
2) FWD connectorNOTE(All AWD AT non-turbo models without
Vehicle Dynamics Control system) Be-
fore driving your vehicle with the tem-
porary spare tire, put a spare fuse in-
side the FWD connector in the main
fuse box located in the engine com-
partment and confirm that the Front-
wheel drive warning light “AWD” in the
combination meter comes on. The all
wheel drive capability of the vehicle
has now deactivated. After re-installing
the conventional tire, remove the spare
fuse from the FWD connector in order
to reactivate all wheel drive.
Flat tiresIf you have a flat tire while driving, never
brake suddenly; keep driving straight
ahead while gradually reducing speed.
Then slowly pull off the road to a safe
place.„ Changing a flat tire
900231
1
2
1
2
600435
y Do not jack up the vehicle on an
incline or a loose road surface.
The jack can come out of the jack-
ing point or sink into the ground
and this can result in a severe ac-
cident.yUse only the jack provided with
your vehicle. The jack supplied
with the vehicle is designed only
for changing a tire. Never get un-
der the vehicle while supporting
the vehicle with this jack.
ProCarManuals.com

Maintenance and service
11 - 3 3
– CONTINUED –
Tire wear varies from wheel to wheel. To
maximize the life of each tire and ensure
that the tires wear uniformly, it is best to
rotate the tires every 7,500 miles (12,500
km). Rotating the tires involves switching
the front and rear tires on the right-hand
side of the vehicle and similarly switching
the front and rear tires on the left-hand
side of the vehicle. (Each tire must be kept
on its original side of the vehicle.)
Replace any damaged or unevenly worn
tire at the time of rotation. After tire rota-
tion, adjust the tire pressures and make
sure the wheel nuts are correctly tight-
ened.
After driving approximately 600 miles
(1,000 km), check the wheel nuts again
and retighten any nut that has become
loose.„Tire replacementThe wheels and tires are important and in-
tegral parts of your vehicle’s design; they
cannot be changed arbitrarily. The tires fit-
ted as standard equipment are optimally
matched to the characteristics of the vehi-
cle and were selected to give the best pos-
sible combination of running performance,
ride comfort, and service life. It is essential
for every tire to have a size and construc-
tion matching those shown on the tire placard and to have a speed symbol and
load index matching those shown on the
tire placard.
Using tires of a non-specified size detracts
from controllability, ride comfort, braking
performance, speedometer accuracy and
odometer accuracy. It also creates incor-
rect body-to-tire clearances and inappro-
priately changes the vehicle’s ground
clearance.
All four tires must be the same in terms of
manufacturer, brand (tread pattern), con-
struction, and size. You are advised to re-
place the tires with new ones that are
identical to those fitted as standard equip-
ment.
For safe vehicle operation, SUBARU rec-
ommends replacing all four tires at the
same time.
„
Wheel replacementWhen replacing wheels due, for example,
to damage, make sure the replacement
wheels match the specifications of the
wheels that are fitted as standard equip-
ment. Replacement wheels are available
from SUBARU dealers.yAll four tires must be the same in
terms of manufacturer, brand
(tread pattern), construction, de-
gree of wear, speed symbol, load
index and size. Mixing tires of dif-
ferent types, sizes or degrees of
wear can result in damage to vehi-
cle’s power train. Use of different
types or sizes of tires can also
dangerously reduce controllabili-
ty and braking performance and
can lead to an accident.yUse only radial tires. Do not use
radial tires together with belted
bias tires and/or bias-ply tires. Do-
ing so can dangerously reduce
controllability, resulting in an ac-
cident.
ProCarManuals.com

Specifications
12-5
„Tires
„ Wheel alignmentTire size
P215/60R16 94H
P215/55R17 93H
Wheel size
16 × 6
1/2 JJ
17 × 7 JJ
Pressure
Front
Light load
29 psi (200 kPa, 2.0 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Full load
29 psi (200 kPa, 2.0 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Rear
Light load
28 psi (190 kPa, 1.9 kgf/cm
2)
30 psi (210 kPa, 2.1 kgf/cm
2)
Full load
36 psi (250 kPa, 2.5 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Trailer towing
41 psi (280 kPa, 2.8 kgf/cm
2)
36 psi (250 kPa, 2.5 kgf/cm
2)
Temporary spare tire
Size
T135/80D16
T135/90D16
Pressure
60 psi (420 kPa, 4.2 kgf/cm
2)
Item
2.5-liter non-turbo models
2.5-liter turbo models
Drive system
AWD
Toe
Front
0 ± 0.12 in (0 ± 3 mm)
Rear
0.079 ± 0.12 in (2 ± 3 mm)
Camber
Front
–0°25’ ± 45’
Rear
–0 °50’ ± 45’
–0 °55’ ± 45’
ProCarManuals.com

13-2
Consumer information and Reporting safety defects
Consumer information and Reporting safety defects
For U.S.A.
The following information has been com-
piled according to Code of Federal Regu-
lations “Title 49, Part 575”.
Tire information„Tire labelingMany markings (e.g. Tire size, Tire
Identification Number or TIN) are
placed on the sidewall of a tire by tire
manufacturers. These marking can
provide you with useful information on
the tire.T
Tire size
Your vehicle comes equipped with P-
Metric tire size. It is important to un-
derstand the sizing system in select-
ing the proper tire for your vehicles.
Here is a brief review of the tire sizing
system with a breakdown of its indi-
vidual elements.
V
P Metric
With the P-Metric system, Section
Width is measured in millimeters. To
convert millimeters into inches, divide
by 25.4. The Aspect Ratio (Section
Height divided by Section Width)
helps provide more dimensional infor-
mation about the tire size. Example:
(1) P = Certain tire type used on light
duty vehicles such as passenger cars
(2) Section Width in millimeters
(3) Aspect Ratio (= section height
÷
section width).
(4) R = Radial Construction
(5) Rim diameter in inches
V
Load and Speed Rating Descrip-
tions
The load and speed rating descrip-
tions will appear following the size
designation.
They provide two important facts
about the tire. First, the number des-
ignation is its load index. Second, the
letter designation indicates the tire’s
speed rating.
Example:
(6) Load Index: A numerical codeP 215 / 60 R 16(1) (2) (3) (4) (5)P 215 / 60 R 16 94 H
Size designation (6) (7)
ProCarManuals.com

Consumer information and Reporting safety defects
13-3
– CONTINUED –
which specifies the maximum load a
tire can carry at the speed indicated
by its speed symbol, at maximum in-
flation pressure.
For example, “94” means 1,477 lbs
(670 kg).(7) Speed Rating: An alphabetical
system describing a tire’s capability to
travel at established and predeter-
mined speeds.
For example, “H” means 130 mph
(210 km/h)
T
Tire Identification Number (TIN)
Tire Identification Number (TIN) is
marked on the intended outboard
sidewall. The TIN is composed of four
groups. Here is a brief review of the
TIN with a breakdown of its individual
elements. (1) Manufacturer’s Identification
Mark
(2) Tire Size
(3) Tire Type Code
(4) Date of Manufacture
The first two figures identify the week,
starting with “01” to represent the first
full week of the calendar year; the
second two figures represent the
year. For example, 0101 means the
1st week of 2001.
T
Other markings
The following makings are also
placed on the sidewall.
V
Maximum permissible inflation
pressure
The maximum cold inflation pressure
to which this tire may be inflated. For
example, “300 kpa (44 PSI) MAX.
PRESS”
V
Maximum load rating
The load rating at the maximum per-
missible weight load for this tire. For
example, “MAX. LOAD 670 kg (1477
LBS) @ 300 kpa (44 PSI) MAX.
PRESS.”
Load indices apply only to the
tire, not to the vehicle. Putting a
load rated tire on any vehicle
does not mean the vehicle can
be loaded up to the tire’s rated
load.
ySpeed ratings apply only to
the tire, not to the vehicle. Put-
ting a speed rated tire on any
vehicle does not mean the ve-
hicle can be operated at the
tire’s rated speed.yThe speed rating is void if the
tires are worn out, damaged,
repaired, retreaded, or other-
wise altered from their original
condition. If tires are repaired,
retreaded, or otherwise al-
tered, they may not be suitable
for original equipment tire de-
signed loads and speeds.
DOT XX XX XXX XXXX
(1) (2) (3)(4)
ProCarManuals.com

Consumer information and Reporting safety defects
13-5
– CONTINUED –
„Recommended tire inflation pressureT
Recommended cold tire inflation pressure
Recommended cold tire inflation pressure for your vehicle’s tires is as follows,Tire size
P215/60R16 94H
P215/55R17 93H
Wheel size
16 × 6
1/2 JJ
17 × 7 JJ
Pressure
Front
Light load
29 psi (200 kPa, 2.0 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Full load
29 psi (200 kPa, 2.0 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Rear
Light load
28 psi (190 kPa, 1.9 kgf/cm
2)
30 psi (210 kPa, 2.1 kgf/cm
2)
Full load
36 psi (250 kPa, 2.5 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Trailer towing
41 psi (280 kPa, 2.8 kgf/cm
2)
36 psi (250 kPa, 2.5 kgf/cm
2)
Temporary spare
tire
Size
T135/80D16
T135/90D16
Pressure
60 psi (420 kPa, 4.2 kgf/cm
2)
ProCarManuals.com

13-6
Consumer information and Reporting safety defects
T
Vehicle placard
The vehicle placard is affixed to the
driver’s side door pillar.
Example: The vehicle placard shows original
tire size, recommended cold tire infla-
tion pressure on each tire at maxi-
mum loaded vehicle weight, seating
capacity and loading information.
T
Adverse safety consequences
of under-inflation
Driving at high speeds with exces-
sively low tire pressures can cause
the tires to flex severely and to rapidly
become hot. A sharp increase in tem-
perature could cause tread separa-
tion, and failure of the tire(s). Possible
resulting loss of vehicle control could
lead to an accident.
T
Measuring and adjusting air
pressure to achieve proper infla-
tion
Check and, if necessary, adjust the
pressure of each tire (including the
spare) at least once a month and be-
fore any long journey. Check the tire
pressures when the tires are cold.
Use a pressure gauge to adjust the
tire pressures to the specific values.
Driving even a short distance warms
up the tires and increases the tire
pressures. Also, the tire pressures are affected by the outside tempera-
ture. It is best to check tire pressure
outdoors before driving the vehicle.
When a tire becomes warm, the air in-
side it expands, causing the tire pres-
sure to increase. Be careful not to
mistakenly release air from a warm
tire to reduce its pressure.
„
Glossary of tire terminologyyCold tire pressure
The pressure in a tire that has been
driven less than 1 mile or has been
standing for three hours or more.yMaximum inflation pressure
The maximum cold inflation pressure
to which a tire may be inflated.yRecommended inflation pres-
sure
The cold inflation pressure recom-
mended by a vehicle manufacturer.yIntended outboard sidewall
1)The sidewall that contains a
whitewall, bears white lettering or
bears manufacturer, brand, and/or
model name molding that is higher
or deeper than the same molding
on the other sidewall of the tire, or
2)The outward facing sidewall of an
800221D00115
ProCarManuals.com

GAS STATION REFERENCE
Fuel:TNon-turbo models
Use only unleaded gasoline with an octane rating of 87 AKI or
higher.
T Turbo models
Use premium unleaded gasoline with an octane rating of 91 AKI or
higher. If premium unleaded gasoline is not available, regular un-
leaded gasoline with octane rating of 87 AKI or higher may be tem-
porarily used. For optimum engine performance and driveability, it
is required that you use premium grade unleaded gasoline.„ Fuel octane ratingThis octane rating is the average of the Research Octane and Mo-
tor numbers and is commonly referred to as the Anti Knock Index (AKI). Refer to “Fuel” section in this manual.
Fuel capacity:15.9 US gal (60 liters, 13.2 Imp gal)Engine oil:Use only API classification SM with the words “ENERGY CON-
SERVING” and the ILSAC certification mark (starburst mark) dis-
played on the container (ILSAC GF-4).Engine oil capacity:4.2 US qt (4.0 liters, 3.5 Imp qt)
Cold tire pressure:Tire size
P215/60R16 94H
P215/55R17 93H
Wheel size
16
× 6
1/2 JJ
17 × 7 JJ
Pressure
Front
Light load
29 psi (200 kPa, 2.0 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Full load
29 psi (200 kPa, 2.0 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Rear
Light load
28 psi (190 kPa, 1.9 kgf/cm
2)
30 psi (210 kPa, 2.1 kgf/cm
2)
Full load
36 psi (250 kPa, 2.5 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Trailer towing
41 psi (280 kPa, 2.8 kgf/cm
2)
36 psi (250 kPa, 2.5 kgf/cm
2)
Temporary
spare tire
Size
T135/80 D16
T135/90 D16
Pressure
60 psi (420 kPa, 4.2 kgf/cm
2)
ProCarManuals.com