ESP SUBARU IMPREZA 2000 2.G Owner's Manual

Maintenance and service10-37
–
CONTINUED –
Replacement of brake pad and lining
CAUTION
If you continue to drive despite the scraping noise from the audi-
ble brake pad wear indicator, it will result in the need for costlybrake rotor repair or replacement.
OM-H0163
The front d isc b rake has an aud ib le wear ind ic ator on the b rake p ad s.
For RS mod els, the rig ht sid e rear d isc b rake also has a aud ib le wear
ind ic ator. If the b rake p ad s wear c lose to their se rvic e limit, the wear ind i-
c ator makes a very aud ib le sc rap ing noise when the b rake p ed al is ap -
p lied .
If you hear this sc rap ing noise eac h time you ap p ly the b rake p ed al,
have the b rake p ad s servic ed b y your SUBARU d ealer as soon as p os-
sib le.
Breaking-in of new brake pads and linings
When rep lac ing the b rake p ad or lining , use only g e nuine SUBARU
p arts. After rep lac ement, the new p arts must b e b ro ken in as follows:
n Brake pad and lining
While maintaining a sp eed of 30 to 40 mp h (50 to 65 km/h), step on
the b rake p ed al lig htly. Rep eat this five or more t imes.

10-44Aluminum wheels (if equipped)
Aluminum wheels c an b e sc ratc hed and d amag ed easily
. Hand le them
c arefully to maintain their ap p earanc e, p erformanc e , and safety.
When any of the wheels is removed and rep lac ed for tire rotation or to
c hang e a flat, always c hec k the tig htness of the wh eel nuts after d riving
ap p roximately 600 miles (1,000 km). If any nut is l oose, tig hten it to the
sp ec ified torq ue. Never ap p ly oil to the thread ed p arts, wheel nuts, or tap ered surfac e
of the wheel. Never let the wheel rub ag ainst sharp p rotrusions o r c urb s.
Be sure to fit tire c hains on uniformly and c omp let ely around the tire,
otherwise the c hains may sc ratc h the wheel. When wheel nuts, b alanc e weig hts, or the c enter c ap are rep lac ed ,
b e sure to rep lac e them with g enuine SUBARU p arts d esig ned for alumi-
num wheels. Fuses
HG0127
HS0202
The fuses are d esig ned to melt d uring an overload t o p revent d amag e to
the wiring harness and elec tric al eq uip ment. The fu ses are loc ated in
two fuse b oxes.
If any lig hts, ac c essories or other elec tric al c ont rols d o not op erate, in-
sp ec t the c orresp ond ing fuse. If a fuse has b lown, rep lac e it.

Consumer information and Reporting safety defects12-3
–
CONTINUED –

Temperature A, B, C
The temp erature g rad es are A (hig hest), B and C, re p resenting the tire’s
resistanc e to g eneration of heat and its ab ility to d issip ate heat when
tested und er c ontrolled c ond itions on a sp ec ified i nd oor lab oratory test
wheel. Sustained hig h temp erature c an c ause the mat erial of the tire to
d eg enerate and red uc e tire life, and exc essive temp erature c an lead to
sud d en tire failure. Grad e C c orresp ond s to a level of p erformanc e
whic h all p asseng er c ar tires must meet und er the F ed eral Motor Vehic le
Safety Stand ard s No. 109. Grad es B and A rep resent hig her levels of
p erformanc e on the lab oratory test wheel than the m inimum req uired b y
law.
WARNING
The temperature grade for a tire is established for one that is
properly inflated and not overloaded. Excessive speed, under
inflation or excessive loading, either separately or in combina-tion, can cause heat buildup and possible tire failure.