ECU SUBARU IMPREZA 2002 2.G Owner's Manual

Keys and doors
2-9
– CONTINUED –
HB1002BC
1) Positive (+) side facing up
4. Replace with a new battery (Type CR2032 or
equivalent) making sure to install the new battery with the positive (+) side facing up.
5. Install the back half of the transmitter case.
6. Reinstall the two screws on the back of the trans-
mitter case. After the battery is replaced, the transmitter must be synchronized with the keyless entry system ’s
control unit. Press either the “LOCK/ARM” or
“UNLOCK/DISARM” button
six times to synchro-
nize the unit.
CAUTION
Do not let dust, oil or water get on or in the
transmitter when replacing the battery.
Replacing lost transmitters
If you lose a transmitter or want to purchase addi-
tional transmitters (up to four can be programmed),
you should re-program all of your transmitters for
security reasons. It is recommended that you have
your dealer program all of your transmitters into yoursystem.
Programming the transmitters
The keyless entry system is equipped with a special
code learning feature that allows you to programnew transmitter codes into the system or to delete
old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may
be the same or different.

Keys and doors
2-10
To enter the programming mode:
HB1000CA
1. Press “UNLOCK/DISARM” button to disarm the
security system. (If your vehicle is equipped with the
optional security system.)
HB1005BC
2. Open the driver ’s door and sit in the driver ’s seat.
3. Close the driver ’s door.
HB2032BC
1) ON 2) LOCK

Keys and doors
2-12
operates by operating each transmitter. Deleting old transmitter codes
The control unit of the keyless entry system has four
memory locations to store transmitter codes, givingit the ability to operate with up to four transmitters.
When you lose a transmitter, the lost transmitter ’s
code remains in the memory. For security reasons,
lost transmitter codes should be deleted from the
memory.
To delete old transmitter codes, program four trans-
mitter codes into the system. If you have only one
current transmitter, program it four times. If you have
two current transmitters, program each one twice. If
you have three current transmitters, program two of
them once and the third one twice. This process will
leave only current transmitter codes in the system ’s
memory. NOTE
Make sure no one else is operating their keyless entry system within range of your vehicle whenprogramming transmitters. If someone else wereto operate their remote transmitter while you are programming your transmitters, it is possible that their transmitter code will be programmedinto your system, allowing them unauthorized
access to your vehicle. Security system (if equipped)
The security system helps to protect your vehicle
and valuables from theft. The horn sounds and the
parking lights flash if someone attempts to break
into your vehicle. The starter motor is also inter-
rupted to prevent starting the vehicle without a key.
The system can be armed and disarmed with the
remote transmitter.The system does not operate when the key is in-
serted into the ignition switch.
System operation
The security system will give the following alarm in-
dications when triggered: The parking lights will flash and the horn will
sound intermittently. In addition, the starter motor willnot operate. The alarm automatically resets after 30 seconds;
however, the alarm will reactivate if the vehicle is
tampered with again. The alarm will continue for sixtimes if any sensor continues to be activated.
The alarm is triggered by: Opening a door, the rear gate or trunk lid.
Application of physical shock to the vehicle (e.g.

Keys and doors
2-13
– CONTINUED –
breaking glass or forced entry). Note that there are
two alarm levels for shock: warning and alarm. In
warning mode, the alarm detects lower level vibra-
tions and triggers 2 warning chirps on the horn and
two flashes on the lights as a deterrent to would be
vandals. In alarm mode, higher levels of shock are
detected and the system will go into full alarm. Ignition switch being turned on while in armed
state. Arming the system
To arm the system using remote transmitter
1. Close all windows.
2. Remove the key from the ignition switch.
3. Open the doors and get out of the vehicle.
4. Make sure that the engine hood (and the trunk
lid) are locked.
5. Close all doors (and the rear gate on the wagon).
HB1000EC
1) Press to Arm the system.
2) Press to Disarm the system.
HG2017BA
Security system indicator light

Keys and doors
2-15
– CONTINUED –
Disarming the system
Briefly press the “UNLOCK/DISARM” button (for less
than two seconds) on the remote transmitter. The
driver’ s door will unlock, the horn will sound two
times, the parking lights will flash two times and the
indicator light will go off.
To unlock all doors (and the rear gate on the
wagon), briefly press the “UNLOCK/DISARM” button
a second time.
Emergency disarming
If you cannot disarm the system using the transmit-
ter (i.e. the transmitter is lost, broken or the transmit-
ter battery is too weak), you can disarm the system
without using the transmitter.
To disarm the system:
1. Unlock the door with the key and then open the
door.
2. The alarm will sound.
3. Insert the key into the ignition switch and cycle it
from the “LOCK” to the “ON” position three (3) times
within 5 seconds .
Sounding a panic alarm
To activate the alarm, keep the “LOCK/ARM” button
pressed for more than two seconds .To deactivate it, press the
“LOCK/ARM” button or
“UNLOCK/DISARM” button.
The parking lights will also flash when the alarm is activated.
Unless a button on the remote is pressed, the alarm
will be deactivated after approximately 30 seconds. Valet mode
When you choose the valet mode, the security sys-
tem does not operate. In valet mode, the remotetransmitter is used only for locking and unlocking
the doors (and rear gate on the wagon) and panicactivation.
To enter the valet mode, open the driver ’s door and
keep the “UNLOCK/DISARM” button depressed for
more than two seconds . The indicator light repeat-
edly flashes two times while the system is in valet mode.
To exit valet mode, open the driver ’s door and keep
the “UNLOCK/DISARM” button pressed for more
than two seconds. The indicator will stop flashing.
Passive arming
When passive arming mode has been programmed
by the dealer, arming of the system is automatically
accomplished without using the remote transmitter.

Keys and doors
2-18
CAUTION
In passive mode, the system will automatically
activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you
must either lock them as indicated in step 4
below or with the key once they have been
closed. Failure to lock the doors manually willresult in a higher security risk.
Disarming the system
To disarm the system, briefly press the “UNLOCK/
DISARM” button on the transmitter.
n Tripped sensor identification
If the horn sounds four times and the parking lights
flash four times when you disarm the system, this in-
dicates that the alarm was triggered. The number oftimes the indicator light flashes indicates what sen-
sor caused the alarm condition.
To enter identification mode:
1. Open the driver ’s door and leave it open.
2. Turn the ignition switch to the “ON” position two
times. ( “LOCK” “ON” “LOCK” “ON”
“LOCK”)
3. The indicator light will start flashing. The indicator light provides the following indications.Flashing one time:
Any door, the rear gate or the
trunk lid has been opened.Flashing three times: The impact sensor in the sys-
tem’ s unit has been activated. This may indicate that
your vehicle has been shocked or tampered with by
some outside force and/or unauthorized person. Flashing four times: The ignition switch has been
turned on or the battery has been disconnected.
To exit this mode, close the door and turn the igni-
tion switch to the “ON” position.

Keys and doors
2-25
– CONTINUED –
Trunk lid release handle
The trunk lid release handle is a device designed to
open the trunk lid from inside the trunk. In the event
children or adults become locked inside the trunk,the handle allows them to open the lid. The handle islocated on the inside of the trunk lid.
To open the trunk lid from inside the trunk, press the
yellow handle downward as indicated by the arrow on the handle.
HBS070BA
This operation unlocks the trunk lid. Then, push up the lid.
The handle is made of material that remains lumi-
nescent for approximately an hour in the dark trunk
space after it is exposed to ambient light even for a short time.
WARNING
Never allow any child to get in the trunk and
play with the release handle. If the driver starts the vehicle without knowing that a child
is inside the trunk and the child opens the lidusing the release handle, the child could fallout and be killed or seriously injured.
CAUTION

Do not close the lid while gripping the re-
lease handle. The handle may be damaged. Do not use the handle as a hook to fasten
straps or ropes to secure your cargo in the trunk. Such use may result in damage of the handle. Load the trunk so that cargo can not strike
the release handle. If the cargo hits the handlewhile the vehicle is being driven, the handlemay be pushed down and the trunk lid may open. That may cause cargo to fall out of the trunk, which could create a traffic safety haz-ard.

Instruments and controls
3-30
Tilt steering wheel
HB4002BA
1. Adjust the seat position. Refer to the “Front seat ”
section (chapter 1).
2. Pull the tilt lock lever down.
3. Move the steering wheel to the desired level.
4. Push the lever up to lock the steering wheel inplace.
5. Make sure that the steering wheel is securely locked by moving it up and down.
WARNING
Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle
control and result in personal injury.

Interior equipment
6-11
– CONTINUED –
Floor mat (if equipped)
A retaining pin is located on the drivers side of the
vehicle next to the fuel filler door release.
HB6016BA
The floor mat is secured using the built-in grommet,
by placing the grommet over the pin and pushing
downward.
CAUTION
Make sure the driver ’s floor mat is placed
back in its proper location and correctly se- cured on its retaining pin. If the floor mat slips
forward and interferes with the movement ofthe pedals during driving, it could cause anaccident.
HB6015BA

Interior equipment
6-14
Cargo anchorage eyelets (if equipped)
HG6011BA
The cargo area is equipped with four anchorage
eyelets so that luggage can be secured with a lug-
gage net or ropes.
When using the anchorage eyelets, turn them down
out of the storing recesses. When not in use, put the
eyelets up into the storing recesses.
CAUTION
The cargo anchorage eyelets are designed only for securing light luggage. Never try to secure luggage that exceeds the capacity of the hooks. The maximum load capacity is 44lb (20 kg) per an eyelet.